User's Manual
Table Of Contents
- Table of Contents
- AD4DDual Channel Receiver
- IMPORTANT SAFETY INSTRUCTIONS
- Australia Warning for Wireless
- AD4D Axient Digital Two-Channel Wireless Receiver
- Included Components
- Mounting Instructions
- Hardware
- Menus and Configuration
- Radio Frequency (RF) Settings
- Setting the RF Tuning Band
- IR Sync
- Setting the Frequency Manually
- Channel Scan and Group Scan
- Requesting a New Frequency from a Spectrum Manager
- Transmission Modes
- Assigning Transmitters to Transmitter Slots
- Interference Management
- Channel Quality Meter
- Frequency Diversity
- Antenna Bias
- RF Cascade Ports
- Firmware
- Audio Settings
- Networking
- Operation
- Troubleshooting
- Specifications
- System Specifications
- RF Carrier Frequency Range
- Working Range
- RF Tuning Step Size
- Channel-to-Channel Spacing
- Channel-to-Channel Spacing
- Image Rejection
- RF Sensitivity
- Latency Analog Output
- Audio Frequency Response
- Signal-to-Noise Ratio(Dynamic Range)
- Total Harmonic Distortion
- System Audio Polarity
- Operating Temperature Range
- Storage Temperature Range
- Audio Output
- Gain Adjustment Range
- Configuration
- Impedance
- Full Scale Output (200K Ω load)
- Mic/Line Switch
- Phantom Power Protection
- Dimensions
- Weight
- Housing
- Power Requirements
- Thermal Power Dissipation
- DC Power Requirements
- Network Interface
- Network Addressing Capability
- Maximum Cable Length
- Cascade Output
- Connector Type
- Configuration
- Impedance
- Insertion Loss
- RF Input
- Spurious Rejection
- Connector Type
- Impedance
- Bias Voltage
- RF Carrier Frequency Range model dependent
- Tables and Diagrams
- Receiver Frequency Bands
- Certifications
- Certifications
- Contact Customer Support
Shure Incorporated
4/41
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
AD4D
Dual Channel Receiver
IMPORTANT SAFETY INSTRUCTIONS
READ these instructions.
KEEP these instructions.
HEED all warnings.
FOLLOW all instructions.
DO NOT use this apparatus near water.
CLEAN ONLY with dry cloth.
DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance
with the manufacturer’s instructions.
DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (in
cluding amplifiers) that produce heat. Do not place any open flame sources on the product.
DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace
ment of the obsolete outlet.
PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
ONLY USE attachments/accessories specified by the manufacturer.
USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
UNPLUG this apparatus during lightning storms or when unused for long periods of time.
REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the
apparatus.
The MAINS plug or an appliance coupler shall remain readily operable.
The airborne noise of the Apparatus does not exceed 70dB (A).
Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connec
tion.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
Operate this product within its specified operating temperature range.