User's Manual

ManualsBrandsShure ManualsComputers & AccessoriesWireless Access Point

Revision: 1.3 (12/21/10)

Showlink 2.4 GHz Detachable

Antenna

Showlink Data Status LED

Power Status LED

Ethernet Status LED

Threaded mounting point

External Power Supply Connector

Reset Settings Button

Ethernet Port

 Scanning Antenna for Channel

Agility

AXT610 Showlink Wireless Access Point

The AXT610 ShowLink wireless access point delivers real-time wireless control of the Axient transmitters. The access point uses

the 2.4 GHz spectrum to relay parameter changes made at the receiver or in Wireless Workbench 6 to the transmitter. All parameter

changes occur instantly without interrupting the performer.

A single access point can support up to 16 transmitters. Multiple access points can be used to extend the control range or increase

transmitter capacity.

Features

Included Accessories

• Expanded coverage range - coverage range is equal to the

broadcasting range of the transmitters

• Automatic network addressing - DHCP IP addressing automatically

configures the network address

• Reliable performance - the access point uses channel agility to scan

and monitor the quality of the 2.4 GHz communication channel.

If channel quality deteriorates, the access point automatically switches

to a clear frequency

• Remote monitoring - remotely monitor access point status and change

settings using Wireless Workbench (WWB) software

• Real-time wireless control of transmitters - make parameter changes

without interrupting performers

• Simple interface - LEDs instantly show the health of the Showlink

connection, Ethernet data, and the power supply

• High transmitter capacity - control 16 transmitters with a single access

point

• Build an expandable network - increase capacity and coverage by

adding more access points to the network

• Convenient power options - uses power over Ethernet (PoE) supplied

by other Axient components for fewer cables

• WA371 wireless microphone clip for mounting on a mic stand

• Euro thread adapter for WA371

• C825 shielded 25-foot Ethernet cable for ShowLink access point, RJ45 to EtherCon connector

AXT610

Axient Wireless

Showlink Acces Point

PUSH













 



DRAFT

Summary of content (5 pages)

PAGE 1
AXT610 Showlink Wireless Access Point The AXT610 ShowLink wireless access point delivers real-time wireless control of the Axient transmitters. The access point uses the 2.4 GHz spectrum to relay parameter changes made at the receiver or in Wireless Workbench 6 to the transmitter. All parameter changes occur instantly without interrupting the performer. A single access point can support up to 16 transmitters. Multiple access points can be used to extend the control range or increase transmitter capacity.
PAGE 2
Showlink Basics ShowLink Channels and 2.4 GHz Spectrum ShowLink channels that enable remote control of Axient transmitters operate in the 2.40 to 2.484 GHz portion of the RF spectrum in accordance with the IEEE 802.15.4 protocol. Within the 2.4 GHz spectrum, 16 channels are available for ShowLink communication. Available spectrum, low interference, and global availability make the 2.4 GHz spectrum an ideal choice for hosting ShowLink channels. Devices that share the 2.
PAGE 3
Positioning the Access Point • Provide a clear line of site between the access point and transmitters: mount the access point on a microphone stand or wall to elevate above crowd level • Position the antenna vertically for optimal performance.
PAGE 4
Specifications Antenna Type Omnidirectional Access Point Capacity 16 transmitters Modulation Type OQPSK Channel Width 5 MHz Mounting Type WA371 Mic Clip Operating Temperature Range -18°C (0°F) to 63°C (145°F) Storage Temperature Range -29°C (-20°F) to 74°C (165°F) Dimensions 186 mm x 101 mm x 46 mm (7.34in.3.960in.1.825in. Weight 476.3 g (16.8 oz.
PAGE 5
Certification AXT610: Certified under FCC Part 15 (FCC ID: DD4AXT610). Certified by IC in Canada under RSS-210 (IC: 616A-AXT610). Transmitters must be installed to provide a minimum separation distance of 20 cm from all persons. The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.