DH5 DuraPlex™ Omnidirectional Headset The Shure Omnidirectional DuraPlex Headset user guide. Version: 1.
Shure Incorporated Table of Contents DH5 DuraPlex™ Omnidirectional Headset General Description Features 9 3 Optional Accessories 9 Replacement Parts 9 4 Attaching the Windscreen 8 Furnished Accessories Adjusting the Headband and Microphone Frequency Response Accessories 3 3 Presence Cap 8 3 Care and Maintenance Reversing the Boom Using the Collar Clip 5 7 7 7 Threaded Mount Instructions 10 Wiring and Termination 10 Typical Wiring Table 11 MTQG Connector Assembly 11 Specificati
Shure Incorporated DH5 DuraPlex™ Omnidirectional Headset General Description The DuraPlex DH5 omnidirectional headset microphone is ideal for both speech and performance applications that require durability and minimal visibility. The bendable lightweight headset features switchable boom mounting placement and a neutral clear design to be used with any DH5 color variant.
Shure Incorporated Care and Maintenance The DuraPlex omnidirectional microphone has been IP57 dust-protected, waterproof rated by extensive internal tests, so you can clean it using distilled water and a mild detergent when necessary. Adjusting the Headband and Microphone ➀ Adjust headband width. ➁ Adjust the earhooks, slide the boom arm in the boom pivot, and twist the pivot to adjust height and length.
Shure Incorporated ➂ Bend boom arm into place. Adjust position. ➃ Use presence cap or leave off. Important: Use slide-fit windscreen with the presence cap Use snap-fit windscreen without the presence cap Reversing the Boom The microphone boom can be positioned on the left or right side of the head.
Shure Incorporated 1. Squeeze the earpiece towards the headband.
Shure Incorporated 2. 3. 4. 5. Push out the boom arm and boom pivot. On the other side, repeat the steps to remove the boom pivot. Move the boom arm to the preferred side, ensuring that the boom arm is placed in the slot in the boom pivot. Squeeze each earpiece towards the headband to push boom pivots back into place. Presence Cap Frequency Response Attaching the Windscreen There are two windscreens for use with the DuraPlex microphone: 1.
Shure Incorporated 2. A snap-fit windscreen for use without the presence cap Note: Do not use the snap-fit windscreen with the presence cap--the presence cap can become caught inside the snap-fit windscreen.
Shure Incorporated Accessories Furnished Accessories Furnished Accessories DH5 Black DH5 Tan DH5 Cocoa Single Tie Clip 95A43715 95A43715 95A43715 Presence Cap 65A44182 65B44182 65C44182 Snap-Fit Windscreen 95A16167 95B16167 95C16167 Foam Windscreen 95A43438 95B43438 95C43438 Sticky Mount 66A44183 66A44183 66A44183 Case 95A44075 95A44075 95A44075 Threaded TA4F Adapter 95A29490 95A29490 95A29490 Accessories are available in Black (/B), Tan (/T), AND Cocoa (/C) color varieties.
Shure Incorporated Description Black Tan Cocoa Microphone Boom Arm and Cable Assembly, Lemo Con nector RPMDH5B/OLM3 RPMDH5T/OLM3 RPMDH5C/OLM3 Microphone Boom Arm and Cable Assembly, MTQG Con nector RPMDH5B/OMTQG RPMDH5T/OMTQG RPMDH5C/OMTQG 5 Boom Pivot, qty. 4 RPMDH5PIVOT RPMDH5PIVOT RPMDH5PIVOT 6 Boom Mount, qty. 4 RPMDH5BM RPMDH5BM RPMDH5BM 7 Headset Frame, qty. 1 RPMDHSF RPMDHSF RPMDHSF Single Tie Clip, qty. 3 RPMDL4STC/B RPMDL4STC/T RPMDL4STC/C Dual Tie Clip, qty.
Shure Incorporated Wiring and Termination Typical Wiring Table Series Cable Con struc tion DL4LEMO 1.6mm cable with single con ductor and shield DL4MTQG 1.
Shure Incorporated Note: Make sure to solder the shield to ground collar. Assembled View Specifications Note: • All specification values are based on using a typical bodypack with 5 V bias input or the RPM400MTQG preamplifier. When using the RPM400LEMO amplifier, refer to the RPM400LEMO specifications. • All specifications measured with a 48 Vdc phantom power supply. The microphone operates at lower voltages, but with slightly decreased headroom and sensitivity.
Shure Incorporated Bias Voltage Recommended Operating Voltage 5 V DC, 2.6 V DC minimum Housing Molded ABS Polarity MTQG Positive pressure on diaphragm produces positive voltage on pin 3 with respect to pin 1 LEMO Positive pressure on diaphragm produces positive voltage on pin 3 with respect to pin 1 Cable Diameter 1.6 mm Cable Length 66 in. (1.67 m) Net Weight DL4 15.0 g(0.53 oz.) DH5 20.0 g(0.7 oz.
Shure Incorporated DH5-MTQG, DH5LEMO Cable Length Cable Diameter Microphone Length Microphone Diameter Boom Length 66 in. (1.67M) 1.6MM 14.5MM 5.2MM 13.6CM Certifications This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking. The CE Declaration of Conformity can be obtained from: www.shure.
