Model PSM200 User Guide PSMR200 Personal Monitor System User Guide >>E2 2002, Shure Incorporated 27B8792 (BJ) >>P2R >>P2T Printed in U.S.A.
ENGLISH WARNING! USING THIS SYSTEM AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A VOLUME AS POSSIBLE. In order to use this system safely, avoid prolonged listening at excessive sound pressure levels. Please use the following guidelines established by the Occupational Safety Health Administration (OSHA) on maximum time exposure to sound pressure levels before hearing damage occurs.
ENGLISH TABLE OF CONTENTS QUICK SET-UP GUIDES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PSM200 Wireless System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 P2R Receiver Quick Set-Up Guide . . . . . . . . . . . . . . . . . . . . .
ENGLISH QUICK SET-UP GUIDES PSMR200 Wireless System The following set-up illustration is for the complete PSM200 Wireless System, which includes the P2T TransMixer, the P2R Receiver, and the E2 Earphones. If you have purchased the P2R as a stand-alone wired personal monitor, see page 4. 1. Plug in the power supply and connect it to the DC input on the rear panel of the P2T TransMixer. 2. Insert a 9 Volt battery into the P2R Receiver, observing proper polarity.
ENGLISH P2R Receiver Quick Set-Up Guide: When Used as a Wired Stand-Alone Personal Monitor Mixing Console 1. Insert a 9 Volt battery into the P2R Receiver, observing proper polarity. 2. Connect an audio source to the 1/4-inch MIX IN jack on the side of the P2R. 3. Turn the P2R volume knob on (past the click). Keep the volume at a low setting. 4. Set the CHANNEL to “A” with the SELECT Button. See the Wired Mode section on page 8 for details. 5.
ENGLISH INTRODUCTION Thank you for buying the PSM200. Like all Shure PSM personal monitoring products, the PSM200 provides the many advantages of in-ear monitoring including: Improved Sound Quality —high fidelity without the risk of feedback, Increased Mobility —your mix moves with you, Personal Control —create a personal mix, and control your own levels. For information on this and other Shure products, visit www.shure.com on the World Wide Web.
ENGLISH THE P2T TRANSMIXER Controls and Features 1 2 4 5 FRONT PANEL: 6 3 BACK PANEL: 7 1. 2. 3. 4. 9 8 MIC/LINE INPUT Jacks: Electronically balanced inputs that accommodate both XLR and 1/4-inch connectors at mic or line levels. Signal/Clip LEDs: Color indicates the signal status of the corresponding MIC/LINE input, as explained in the Audio Inputs and Outputs section below. INPUT Knobs: Control the level of their corresponding inputs.
ENGLISH P2R RECEIVER Controls and Features 12 11 2 1 3 7 4 5 8 9 10 6 13 1. POWER LED: Lights to indicate the unit is powered on and blinks to indicate low battery. When this LED starts blinking, you have approximately 15 minutes of battery time remaining, depending on volume level and battery brand. 2. On/Off/Volume Knob: Turn clockwise past click to power on. Continue to turn clockwise to increase volume, counterclockwise to decrease volume. 3.
ENGLISH Wireless Mode When you are using the P2R as a wireless receiver, or as a combination wired and wireless receiver, use the SELECT button on the side of the P2R Receiver to set the frequency channel (1-8). To Select a Frequency Channel: 1. 2. 3. Press and hold the SELECT button until the CHANNEL LED indicator begins to flash. When the LED indicator is flashing, press the SELECT button to scroll to the desired frequency channel. Release the button.
ENGLISH SET-UP Wireless System Set-Up To configure the P2T TransMixer and P2R Receiver for wireless operation: 1. Plug the power supply into the DC INPUT connector on the 5. rear panel of the P2T, then plug it into a power outlet. 2. Connect audio sources to the combo XLR/1/4-inch jacks on the front panel. 6. 3. Select a frequency channel (1-8). See the Selecting a Frequency Channel section on page 6 for details. 7. IMPORTANT: Never set more than ONE 8.
ENGLISH SYSTEM APPLICATIONS This section presents three typical applications for the PSM200. For more ideas, visit Shure’s website at www.shure.com. APPLICATION ONE: Wireless Set-Up for a Vocalist This is the basic wireless configuration of the PSM200 system for a single user, either instrumental or vocal: 1. Connect the vocal mic to INPUT 1 of the P2T TransMixer. 2. Connect SPLIT OUT 1 from the P2T to the Mixing Console. 3. Connect the instrumental mix line out to INPUT 2 of the P2T. 4.
ENGLISH APPLICATION THREE: Two PSM200 Wireless Systems Used Simultaneously* The following configuration uses two PSM200 systems simultaneously, and utilizes the SPLIT OUT feature of the TransMixer. In this example, the musicians keep the TransMixers on stage with them, in order to control their personal mixes independent of the house engineer. 1. Connect the vocal mic to INPUT 1 of the Vocal Mix TransMixer and connect SPLIT OUT 1 (the vocals) to the Mixing Console. 2.
ENGLISH TROUBLESHOOTING PROBLEM SOLUTION No sound at the receiver Check the power cord on the TransMixer and make sure it is powered on. Make sure both the TransMixer and the P2R Receiver are set to the same frequency channel. Make sure the earphones are plugged in to the receiver and the volume is up. Make sure the Receiver is on and the battery is good. Check the incoming audio connections on the TransMixer.
ENGLISH P2T Audio Input XLR/1/4-inch Connector Type: P2T Audio Outputs Passive connection parallel with input.
ENGLISH Certifications PS20: Conforms to applicable U.S. and Canadian electrical and safety standards. PS20E/PS20UK: Conforms to European low voltage directive 72/23/EEC. Eligible to bear CE marking. P2T: Certified to FCC Part 74 (FCC ID No. DD4P2T). Certified in Canada by IC to RSS-123 and RSS-102 (Certification No. 616A-P2T). This class B digital apparatus complies with Canadian ICES–003. EP2T/UKP2T: Meets essential requirements of European R&TTE DiO682 rective 99/5/EC, eligible to bear the CE mark: .
Declaration of Conformity EU DECLARATION OF CONFORMITY We of Shure Incorporated 222 Hartrey Ave. Evanston IL 60202-3696 U.S.A. 847-866-2200 We, of Declare under our sole responsibility that the following products declare under our sole responsibility that the following products, Model: P2R Name: P2R Receiver were tested and found to comply with Part 15 of the FCC rules.
SHURE Incorporated Web Address: http://www.shure.com 5800 W. Touhy Avenue, Niles, IL 60714–4608, U.S.A.