LX Wireless System User Guide LX Wireless System ©2003, Shure Incorporated 27D8654 (Rev. 6) Printed in U.S.A.
LX Wireless System READ ME FIRST! To get your system up and running in just a few minutes, follow the simple instructions on this page. For more detailed information, refer to the sections of this guide that apply to your system. RECEIVER CONNECTIONS 1. Attach the antennas to the receiver antenna connectors. 2. Connect the AC power adapter to the receiver power connector; then plug it into an ac electrical outlet. 3.
English TABLE OF CONTENTS TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SYSTEM COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 SYSTEM FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 LX1 BODY-PACK TRANSMITTER FEATURES, CONTROLS AND INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LX Wireless System SYSTEM COMPONENTS WIRELESS RECEIVER LX3 LX1 AUDIO RF SQUELCH LEVEL POWER LX2 MARCAD DIVERSITY LX4 RF A RF B AUDIO SQUELCH LEVEL POWER LX WIRELESS MICROPHONE SYSTEM COMPONENTS FIGURE 1 Your LX Wireless Microphone System features a MARCAD® fixed frequency diversity receiver operating in the VHF band between 169 and 240 MHz. Up to 12 LX wireless systems can be operated simultaneously in a single installation.
English SYSTEM FEATURES Shure LX Wireless Systems offer a number of exceptional features, including: • Exclusive Shure MARCAD Circuitry (LX4). MARCAD (MAximum Ratio Combining Audio Diversity) circuitry constantly monitors signals from both receiver sections and combines them to create a single output signal. The result is improved reception and exceptional freedom from dropouts. Half-Rack Receiver Size.
LX Wireless System LX1 BODY-PACK TRANSMITTER FEATURES, CONTROLS AND INDICATORS LX1 BODY-PACK TRANSMITTER FEATURES, CONTROLS AND INDICATORS FIGURE 2 Antenna. A flexible wire antenna is permanently attached to the bottom of the LX1 body-pack transmitter. For best operation, the antenna must hang in the vertical position, and should not be coiled or bundled. Battery Compartment. Hinged cover on bottom surface exposes the battery.
English LX2 HANDHELD MICROPHONE-TRANSMITTER FEATURES, CONTROLS AND INDICATORS LX2 MICROPHONE-TRANSMITTER FEATURES, CONTROLS, AND INDICATORS FIGURE 3 Grille. Protects the microphone cartridge and helps reduce breath sounds and wind noise. The grilles for the various microphone heads differ in appearance. Power Switch. Turns transmitter power on and off. Power/Battery Fuel Gauge.
LX Wireless System LX3 RECEIVER FEATURES, CONTROLS AND INDICATORS FRONT WIRELESS RECEIVER SQUELCH LEVEL POWER AUDIO RF OUTPUT HI Z REAR POWER ANT 12.5 – 18.9 VDC LX3 RECEIVER CONTROLS, FEATURES, AND INDICATORS FIGURE 4 RF Presence Indicators. Glows amber when the antenna is receiving usable RF (radio frequency) signals. Audio Level Indicators. Five lights glow to indicate audio signal strength. Green lights indicate normal operation.
English LX4 DIVERSITY RECEIVER FEATURES, CONTROLS AND INDICATORS MARCAD DIVERSITY SQUELCH LEVEL RF A HI Z ANT POWER AUDIO RF B OUTPUTS BAL POWER B ANT A MIC LINE 쐅 12.5 – 18.9 VDC 쐈 LX4 DIVERSITY RECEIVER FEATURES, CONTROLS AND INDICATORS FIGURE 5 Diversity Signal Indicators for A and B Antennas. These lights glow amber when A, B, or both antennas are receiving usable RF (radio frequency) signals. RF Level Indicators.
LX Wireless System RECEIVER MOUNTING SINGLE RACK-MOUNTED RECEIVER (FIGURE 6) If the receiver is to be located on a table or other horizontal surface, attach the four adhesive bumpers to the bottom corners of the receiver. If the receiver is to be mounted in an audio equipment rack, identify the rack-mount kits supplied with your system and follow the appropriate assembly directions below. 1. Remove two screws from each side of the receiver. 2.
English RECEIVER CONNECTIONS 1. Attach the supplied quarter-wave antenna(s) to the antenna connector(s) on the receiver back panel. For best performance, the LX4 receiver antennas should be oriented with the tips pointing away from each other at a 45° angle from vertical. The LX3 receiver antenna should be vertical. 2. Connect the receiver output to the mixer or amplifier input, using a standard audio cable with a female 3-pin XLR connector or 1/4-inch phone plug. 3.
LX Wireless System TRANSMITTER SETUP LX1 BODY-PACK TRANSMITTER BATTERY INSTALLATION 1. With the transmitter POWER PWR/OFF switch in the OFF position, press down on the OPEN side of the battery compartment cover, slide it back and flip it open. 2. Insert a new 9V alkaline battery in the compartment. Observe proper battery polarity (“+/–”). LX1 BODY-PACK TRANSMITTER BATTERY INSTALLATION FIGURE 9 IMPORTANT: A fresh 9V alkaline battery should provide 18 to 20 hours of operation. However, an 8.
English CHECKING THE TRANSMITTER BATTERY Turn the transmitter PWR/OFF switch to the PWR position and observe that one or two of the three lights on the transmitter glows. The amount of battery life remaining will be indicated by the color of the light(s), as shown in the following table.
LX Wireless System ATTACHING THE LX1 TO A BELT OR GUITAR STRAP Attach the LX1 body-pack transmitter clip to a belt, waistband, or guitar strap by depressing the tab marked PRESS and slipping the belt or strap between the transmitter body and the belt clip, as shown in Figure 11. The clip holds tightest if the material is drawn to the clip's top wire (especially thinner guitar straps).
English WH20 HEADSET WM98 MIC AND AK98KCS MOUNT LAVALIER MICROPHONE WA302 INSTRUMENT ADAPTER CABLE RECEIVER FIGURE 14 LX1 BODY-PACK SYSTEM SETUP AND OPERATION OPERATING LX1 BODY-PACK SYSTEMS 1. Clip the LX1 body pack transmitter to your belt, waistband, or guitar strap. 2. Connect the lavalier microphone, headset or instrument adapter cable to the bodypack transmitter. 3. If you are using a lavalier microphone, clip the mic to your tie, lapel, or other garment.
LX Wireless System OPERATING THE LX2 HAND-HELD SYSTEM LX2 TRANSMITTER RECEIVER LX2 HAND-HELD MICROPHONE SYSTEM OPERATION FIGURE 15 1. Slide the transmitter PWR/OFF switch to the PWR position. One of the three lights on the transmitter illuminates. 2. Press the POWER button on the receiver. The green power on indicator and the RF light(s) illuminates. 3. Slide the transmitter ON/MUTE switch to the ON position and begin speaking or playing your instrument.
English GAIN AND SQUELCH ADJUSTMENT ADJUSTING THE TRANSMITTER AUDIO GAIN LEVEL The transmitter audio gain level has been factory pre-set to provide satisfactory output in most applications. However, for loud singers or high-output musical instruments, the preset level may be too high, as indicated by the constant glow of the red light on the receiver audio level meter.
LX Wireless System ADJUSTING THE RECEIVER SQUELCH CONTROL The receiver squelch control is factory preset at the 12 o'clock position for optimum performance. No further adjustment is normally required. However, it is possible to adjust the squelch control to emphasize either signal quality or system range. • To raise the squelch threshold, rotate the control clockwise. This causes the receiver to demand a higher quality signal (less noise before muting), but it reduces the operating range.
English TROUBLESHOOTING 18 Problem Solution No sound; receiver RF light(s) and AUDIO lights not glowing. Make sure POWER switches on transmitter and receiver are on. Check transmitter Power/Battery Fuel Gauge to ensure that battery is providing power. Replace battery if necessary. Check receiver squelch setting. Check receiver antenna connection(s). Make sure at least one antenna is in the line of sight of the transmitter. If necessary, reduce the distance between transmitter and receiver.
LX Wireless System SPECIFICATIONS RF Carrier Frequency Range 169.445 to 240.000 MHz (available frequencies depend on the applicable regulations in the country where the system is used) Working Range 91 m (300 ft) under typical conditions. NOTE: Actual working range depends on RF signal absorption, reflection and interference. Audio Frequency Response 50 to 15,000 Hz, +2 dB. NOTE: Overall system frequency response depends on the microphone element.
English Overall Dimensions LX1: 83 mm H x 64 mm W x 26 mm D (31/4 x 21/2 x 11/32 in.) LX2/58, LX2/BETA 58: 241 mm L x 51 mm Dia. (91/2 x 2 in.) LX2/87, LX2/BETA 87: 216 mm L x 51 mm Dia. (81/2 x 2 in.) LX3, LX4: 43 mm H x 214 mm W x 183 mm D (111/16 x 87/16 x 73/16 in.) Net Weight LX1: 79 g (2.8 oz.) without battery LX2/58, LX2/BETA 58: 295 g (10.4 oz.) without battery LX2/87, LX2/BETA 87: 193 g (6.8 oz.) without battery LX3: 1,049 g (2 lbs, 5 oz.) LX4: 1,105 g (2 lbs, 7 oz.
LX Wireless System Antenna/Power Distribution System, 230 Vac . . . . . . . . . . . . . . . . . . . . . . . . . WA405E 1.8 Meter (6 ft.) Receiver-Mixer Cable (1/4" phone to XLR) . . . . . . . . . . . . . . . .WA410 6.1 Meter (20 ft.) Antenna Extension Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . .WA421 Antenna Rack Mount Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .WA440 Passive Antenna Splitter . . . . . . . . . . . . . . . . . . . . . . . . . . .
English LICENSING INFORMATION Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the user's responsibility, and licensability depends on the user's classification and application, and on the selected frequency.
LX Wireless System FULL TWO YEAR WARRANTY Shure warrants this product to be free in normal use of any defects in workmanship and materials for two (2) years from the date of purchase. If your Shure product fails within this period, call 1-800-516-2525 in the United States for details on repair, replacement, or refund. In Europe, contact Shure Incorporated Europe GMBH at +49 (7131) 7214-0 or +49 (7131) 7214-30 (service hotline) or contact your authorized Shure distributor.
English 112
Trademark Notices: The stylized Shure logo, and the word “Shure” are registered trademarks of Shure Incorporated in the United States. “Pelican” is a registered trademark of Pelican Products, Inc. SHURE Incorporated Web Address: http://www.shure.com 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A. In U.S.A.