MXW Microflex® Wireless The Shure microflex wireless system, MXW, user guide.
Shure Incorporated Table of Contents MXWMicroflex® Wireless 4 IMPORTANT SAFETY INSTRUCTIONS 4 Overview 4 General Description 5 Features 5 MXW Wireless System 7 Shure SystemOn Software For Managing Large Systems 5 2 High Density Mode 52 Configurations: Managing Multiple Groups 53 Wireless Management 54 Overview of Channel Coordination 54 Scanning Available RF Spectrum 55 PHS Detection 57 10 Identifying PHS Detection Errors 57 Audio Network Interface (ANI) 11 Setting RF Power 59
Shure Incorporated Audio Network Interface (ANI) 96 Transmitter Output Power 98 Wiring Diagram 99 WARNING Important Product Information Information to the user Safety Information 100 100 101 100 SAFETY PRECAUTIONS 100 WARNING 100 Certifications 101 Trademarks 102 3/102
Shure Incorporated MXW Microflex® Wireless IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. READ these instructions. KEEP these instructions. HEED all warnings. FOLLOW all instructions. DO NOT use this apparatus near water. CLEAN ONLY with dry cloth. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturer’s instructions.
Shure Incorporated Overview General Description The Shure Microflex Wireless Series (MXW) is a complete microphone solution for flexible meeting rooms and boardrooms. It features automatic RF channel management, rechargeable wireless microphones with encryption (AES256), and digital audio networking using Dante™. The MXW Access Point (APT) mounts to a ceiling or wall for discreet communication between the wireless microphones and the digital audio network.
Shure Incorporated Rechargeable Micro phones Each MXW microphone is powered from a rechargeable Lithium-ion battery, which can be charged at any time without removal from the microphone. Battery statistics are viewable from the control software (battery runtime, time to full charge, charge cycle count and battery capacity). Discreet, Professional De sign Modern, lowprofile wireless microphone designs elegantly integrate into diverse AV environ ments.
Shure Incorporated MXW Wireless System ① Wireless Microphones ② System processor and wireless transceiver ③ Microphone linking and charging station ④ Analog output device with gigabit network switch ⑤ Shielded Cat5e cables (not included) Components of the MXW System Microphone Transmitters MXW microphones transmit an encrypted, wireless audio signal to the access point. Four form factors are available: Hybrid Bodypack (MXW1) The bodypack secures to a belt or strap for hands-free, mobile communication.
Shure Incorporated Access Point Transceiver (MXWAPT2, MXWAPT4, MXWAPT8) The Access Point Transceiver (2, 4 and 8 channel units) mounts to a wall or ceiling to manage encrypted, wireless audio con nections with microphones. As a system hub, it transports digital audio between the wireless microphones and other Dante de vices on the same network. The APT includes a webserver that hosts the MXW System control software, used for monitoring, configuration, and remote control of the system.
Shure Incorporated Networked Charging Station (MXWNCS2, MXWNCS4, MXWNCS8) The Networked Charging Station (2, 4 and 8 slot varieties) is capable of simultaneous charging MXW microphones. It also links microphones to access point channels and networks battery statistics to the control software. Note: The MXWNCS2 does not work with the MXW8 gooseneck microphones. MXW Control Software The MXW control software offers comprehensive remote control of key setup, monitoring and management functions.
Shure Incorporated Important: Desktop Gooseneck Base Microphones (MXW8) occupy two charging slots. For example, eight MXW8 micro phones require two MXWNCS8 charging stations (16 charging slots total). System Design and Technology Technology Overview of the Audio Path The MXW System combines Shure legendary audio quality with advanced digital networking technology.
Shure Incorporated Hardware Description Audio Network Interface (ANI) Front Panel ① Input Channels Adds analog line- or aux-level signals to the digital network. When the device is associated to an MXW Group, inputs are automatically routed to Linked microphone channels (Input A to channels 1-4; Input B to 5-8). ② Output Channels Converts digital network audio to an analog output for each channel. When associated to an MXW group, access point channels are automatically routed to the outputs of the ANI.
Shure Incorporated ⑦ Input Level Selector Set the selected channel to line- or aux-level to match the input signal. ⑧ Output Level Selector Set the selected channel to an output level that matches the connecting device: ◦ line: +4 dBu ◦ aux: -10 dBV ◦ mic: -30 dBV ⑨ Output Attenuation Control Use the up/down buttons to attenuate the channel output from 0 dB (no attenuation) to -24 dB in 1 dB increments, and from -24 to -78 in 3 dB increments.
Shure Incorporated Back Panel ① AC Power IEC connector 100 - 240 V AC. ② Power Switch Powers the unit on or off. ③ Output Block Connectors (1-8) Three-pin, low-voltage differential connector provides a line-, aux- or mic-level analog output for each channel. ④ Chassis Ground (1-8) Use to directly ground the cable shield to the chassis. ⑤ Input Block Connectors (A,B) Three-pin, low-voltage differential input connector adds line- or aux-level analog signals to the digital network.
Shure Incorporated Port Description Ports 2 and 3 Standard gigabit ports enable the connection of another MXW network, additional MXWANIs, a MXWNCS charging stations or an external control system. Port 4 (Uplink) Normal mode (default): this port functions the same as ports 2 and 3. Uplink Mode: only transports control data. This mode blocks network audio and data for Shure Web Discovery Application, Dante Controller and Dante Virtual Soundcard.
Shure Incorporated Color Status Green All routed receive channels are OK (receiving digital audio as expected). Flashing Green One or more connected receive channels experiencing a subscription error or is unresolved (trans mitting device is off, disconnected, renamed or has incorrect network setting). Receiving an Identification signal from the control software (simultaneous flash with Link Status LED). The device is performing a spectrum scan (alternating flash with Link Status LED).
Shure Incorporated Directional Antennas The access point contains multiple directional antennas to provide steady, reliable wireless communication with the micro phones. It sends and receives the RF signal in a cardioid pattern with the greatest sensitivity toward the face of the device. Al ways aim this side toward the microphone coverage area. Cardioid RF Pattern Networked Charger (NCS) The MXW networked charging station enables battery charging and channel linking from a single location.
Shure Incorporated ① Charging Slots (USB 3.0 Type A) Recharge and link microphones by connecting them to the USB slots on the charger. When the charger is associated to a group, the slots are mapped to access point channels (See Audio Channel Assignment for details). Note: Any microphone can charge in any charger, regardless of Group association or network connection. ② Power LED Illuminates green when the unit is powered on.
Shure Incorporated Monitors the charge status of the connected microphone in increments of <10, 10, 25, 50, 75, 100% (see Batteries for more detail). Additionally, the five LEDs flash for several seconds when the microphone has been successfully linked to the chan nel. ⑥ Locking DC Power Supply Secures the PS60 power supply to the input jack of the station. ⑦ Power Switch Powers the unit on or off.
Shure Incorporated MXW1, MXW2: Press and hold the Mute/Active button for five seconds to turn the transmitter on or off. ② Mute/Active Button Changes the audio status from Active to Mute, or Mute to Active. The button behavior for each transmitter type can be set independently from the Preferences tab. The following describes the function of each setting: ◦ ◦ ◦ ◦ Toggle: Press and release the button to change the status to Active or Mute. Push-to-talk: Hold button to pass audio.
Shure Incorporated Status LED Table Status LED Description Active Green Ready to pass audio to network. Mute Red Audio is muted. Standby Red Pulsing (long off, short on) Audio is muted and the transmitter is in a hibernation state to con serve the battery. Identify Flashing Yellow The Identify button has been pressed from the control software. The transmitter is initializing and acquiring the RF connection to the linked access point.
Shure Incorporated Wearing the Bodypack Transmitter • Clip the transmitter to a belt or pocket. • For best results, the belt should be pressed against the base of the clip. Handheld (MXW2) The handheld enables presenters to communicate using legendary Shure SM58, SM86, BETA58 and VP68 microphone car tridges.
Shure Incorporated Correct Microphone Placement • Hold the microphone within 12 inches from the sound source. For a warmer sound with increased bass presence, move the microphone closer. • Do not cover grille with hand. Boundary (MXW6/C, MXW6/O) The boundary transmitter sits on a table or desk to transmit speech while discreetly blending into any conference environment. Cardioid and omnidirectional versions are available.
Shure Incorporated Desktop Gooseneck Base (MXW8) The gooseneck base is compatible with 5, 10, and 15” Microflex gooseneck microphones.
Shure Incorporated MX405, MX410 & MX415 Bi-color Status Indicator MX405R, MX410R & MX415R Light Ring Rechargeable Batteries MXW lithium-ion rechargeable batteries use advanced chemistry that maximizes transmitter runtime. Power management from the control software provides detailed visibility to critical battery parameters such as charge status, battery capacity, and cycle count. Batteries charge to 50% capacity in one hour and to full capacity in two hours using the MXW Networked Charging Station.
Shure Incorporated Microphone Type Battery Model MXW8 gooseneck base MXW2 handheld SB902A Networked Charging Station (NCS) Slide the transmitter into the charging slot until it secures into place. The charge LEDs illuminate when the charge cycle begins. Regardless of Group association or network connection, any microphone can recharge in any NCS. • Handheld, boundary and bodypack: use the main vertical slots in the recessed bays. • Gooseneck base: uses the top row's horizontal connectors.
Shure Incorporated Note: The LEDs do not illuminate in Energy Efficient Mode. NCS Power Modes The charging station can be operated in different power modes other than standard charging mode: Energy Efficient Mode Operate the charger in a low-energy mode to reduce power consumption. In this mode, only one LED indicator illuminates per channel after powering on. To change to Energy Efficient Mode: 1. 2. 3. 4. 5. Open the MXW control software to the Utility page.
Shure Incorporated Battery Statistics on Control Software The MXW control software is used to manage battery information. Use the Monitor tab to view battery charging status: Monitoring Battery Charge Status In the Charging Station Displays the remaining time until the microphone battery is fully charged. During Use Displays the remaining battery runtime of the microphone.
Shure Incorporated Caution: Securely hold the microphone while pressing the button to avoid damaging the USB ports on the charging station. Maximizing Battery Life While the rechargeable LiIon batteries for MXW transmitters are designed to last up to 9 hours on a charge, variance in bat tery health and use-case may result in significant differences in battery runtime. Specifically, consistency and overall runtime decrease with the number of charge cycles.
Shure Incorporated Important: After installing a new battery, reset the battery health statistics that are stored in the microphone following the steps in Reset the Microphone Battery Statistics in the previous section. MXW1, MXW6, MXW8 Battery Replacement 1. 2. 3. 4. 5. 6. Unscrew and open the battery door on the bottom of the transmitter. Remove battery by gently disconnecting the battery connector from the transmitter. Connect the replacement battery's connector to the transmitter.
Shure Incorporated For systems with more than one APT, a DHCP router is recommended to connect equip ment. Ensure that it meets the following requirements: Gigabit DHCP Router (sys tems with >1 APT) • • • • • Gigabit ports Provides Class 0 PoE with at least 6.5W (for powering the MXWAPT) Quality of Service (QoS) with 4 queues Diffserv (DSCP) QoS, with strict priority If the router features Energy Efficient Ethernet (or Green Ethernet), ensure it is disabled from the ports dedicated for the MXW system.
Shure Incorporated *When Port 4 is set to Uplink mode, Shure Discovery Application support is restricted. Multiple Group System (>1 Access Point) When an installation requires more than eight channels, additional MXW components can be connected to expand the system. A gigabit router is required to connect all components to the same network. The following are several topologies for multiple group systems. Use the Spectrum Scanner to ensure that there is sufficient RF availability for the installation.
Shure Incorporated 3. 4. 5. 6. Connect the router to Port 2, 3, or 4 on the Audio Network Interface Connect the Access Point Transceiver to the Port 1 of the Audio Network Interface. Connect the Network Charging Station(s) to an open port(s) on the Audio Network Interface. Repeat steps 2 - 4 for additional equipment. Rack Installation Rackmount the device using the screws and washers supplied in the Hardware Kit.
Shure Incorporated Required Thread Exposure Use counterbore and washers as necessary depending on thickness of table NCS Mounting Template Two-Channel Charger Wall Mount The two-channel charger includes a wall-mount to provide quick microphone access and storage in a classroom or conference room.
Shure Incorporated NCS2 Secures to a Classroom Wall Tip: Paint the mount to match the wall for a less obtrusive installation. Installation 1. Determine the orientation and placement of the mount. Placement Orientation Wall Drawer or tray 2. Leave room around the mount for cabling to the charging station.
Shure Incorporated 3. Attach the mount to the wall. Use one set of screw holes depending on the orientation of the mount. Mount Screw Holes 4. Align the charger on the mount and secure with the screws. Tip: Improve cable management using the cable tie holes on the mount.
Shure Incorporated NCS2 Mount Dimensions Side View 36/102
Shure Incorporated Top View 37/102
Shure Incorporated Overall Dimensions Mount the Access Point Transceiver The directional antennas of the APT send and receive the RF signal in a cardioid pattern with the greatest sensitivity toward the face of the device. Always aim this side toward the microphone coverage area. Select a Location The access point is typically mounted to a ceiling or wall near the microphone coverage area.
Shure Incorporated • Keep at least eight feet between access points. • Mount with its reset button accessible, as it may be useful for troubleshooting. Important: Always perform a "walk around" test to verify coverage before using a wireless system during a speech or perfor mance. Experiment with antenna placement to find the optimum location. If necessary, mark "trouble spots" and ask presenters or performers to avoid those areas.
Shure Incorporated External Cover for Painting The Access Point is supplied with an external cover that can be painted to match the decor of the installation. After it has been painted and dried, it snaps onto the front plate of the device. Power the Hardware ① Audio Network Interface (ANI) Connect the IEC power cable from the back panel to an AC power source. Turn on the power switch. ② Access Point Transceiver (APT) Connect a shielded Cat5e cable from the MXWAPT to network Port 1 of the MXWANI.
Shure Incorporated ③ Networked Charging Station (NCS) Connect the PS60 external power supply from the charger to an AC power source. Turn on the power switch. Fully Charge the Transmitters Whenever possible, charge to full the MXW transmitters before an event. Transmitters can be charged in any networked charg ing station, even if it is associated to another Group or on a separate network.
Shure Incorporated There are two different control interfaces for MXW devices: • MXW system (hosted in APT): For comprehensive control of key setup, monitoring and management functions for the MXW system. Accessed from the Access Point Transceiver (APT). • Audio Inputs and Outputs (hosted in ANI): For sending audio channels on and off the Dante network. Accessed from the Audio Network Interface (ANI). 1. Get the Shure Web Device Discovery application.
Shure Incorporated Start with the APT and select the corresponding devices: • Chargers: for linking microphones • Audio outputs: for routing audio to analog outputs Group Components from the Network Once the group formed, microphones can be linked to channels using the charging station. Select Devices for the Group Use the MXW control software to view devices on the network and assign them to a group. Tip: Use the ID button to identify a device. This flashes the component LEDs for easy identification.
Shure Incorporated 1. Go to the Configuration Tab 2. Select the Access Point Transceiver (APT) for Group 1 Assign the devices to groups from the Configuration tab of the MXW control software. Select an APT to determine group channel count (2, 4 or 8). Group 1 automatically uses the APT opened from the Web Discovery application. Other networked (and open) APTs are available for additional groups. Select one or two Network Charging Station (NCS) to the access point.
Shure Incorporated Device Availability When setting up a group or managing devices, it is important to understand the difference between open and associated de vices. Open Device A device that is not associated to a group is considered 'open.' Open devices are available for association by selecting the drop-down window in a Group row. The device will show Open in the Group column of the Utility page. Associated Device A device is considered 'associated' once it has been selected in a group row.
Shure Incorporated 2. Perform a factory reset on the devices (see the Factory Default section). 3. On the front panel of the ANI, press both input level selection buttons at the same time and hold for five seconds. The Channel Select LEDs will illuminate green and the audio meter will flash to indicate that the association is successful. Channel Routing between Devices Channels are routed when charging stations and output devices are selected to fill the APT group (2-, 4-, or 8-channels).
Shure Incorporated Gooseneck Microphones This setup is used to fill an 8-channel group with gooseneck microphones. Channels are rerouted when an additional charger is added to the group. (The gooseneck base is larger and covers two charger slots.) Mixture of Gooseneck and Boundary Microphones When 4-channel and 8-channel chargers are selected, group channels five through eight are automatically routed to the back row of the 8-channel charger.
Shure Incorporated Audio Output Examples 8-Channel Group 8-Channel SCM820 Digital Automatic Mixer Channels are routed to the eight outputs of the mixer. Two 4-Channel Audio Network Interfaces Channels are routed across both interfaces to fill the group. 4-Channel Group 8-Channel Audio Network Interface Channels are routed to the first four outputs of the interface. Link Microphones to Group Channels Use the Networked Charging Station (NCS) to Link microphones to Access Point channels.
Shure Incorporated Microphones are Linked to access point channels according to the arrangement in the charger. Note: 2-channel chargers do not support gooseneck microphones. 1. Arrange microphones in the charger. Connecting the Microphone to the Charger Slot Use the control software or the charging station to Link the microphones to APT channels. If desired, this feature can be disabled on the charging station so that Linking can only be per formed from the control software: 2.
Shure Incorporated Preparing a Backup Microphone Prepare an alternate microphone for each channel for more reliable and flexible events. Two MXW microphone transmitters can be linked to the same channel, providing the option of either microphone for use. Link a mic to the secondary slot to anticipate needs that may arise during events: Microphone Preference Give presenters a choice between two different microphone types, such as handheld or bodypack microphones.
Shure Incorporated One Active Mic per Channel Only one microphone will operate on the channel at a time, blocking the second microphone from interfering with the RF and audio performance. The backup microphone briefly flashes the LED to indicate the channel is occupied, and automatically turns off to conserve the battery. To use the second microphone, simply turn off the first microphone. Two Microphones Ready for the Audio Channel The system allows one live microphone per channel.
Shure Incorporated Remove a Device from a Group To remove a device from a group, open the MXW Control Software and go to the Configuration tab. In the group row, select the device drop-down window that contains the desired device. Select 'none' to clear the device association. Note: A factory reset will also remove the any association or Link status.
Shure Incorporated Density Mode Comparison Feature Standard Density High Density Channels available* Up to 40 Up to 80 Audio latency 18 ms 28 ms Microphone battery life Up to 7 hours Up to 8 hours EQ filters Optional Always on Backchannel audio (headphone out put on the microphone) Available Unavailable *For Americas region. See Maximum Channel Count table for availability worldwide. Setting the Density Mode Set the mode for each APT from the device properties: 1.
Shure Incorporated 2. Select the Access Point that will be used for the new Configuration and open its control software. The APT must be open (not already assigned to a group) in order to start a new configuration. 3. Go to the Configuration tab. 4. Select that Access Point from the drop down list in Row 1. Use the ID button to ensure the correct Access Point is se lected. 5. Select the charging station(s) and output device(s) to complete the Group. 6. Repeat 4-5 for up to 10 Groups in the Configuration.
Shure Incorporated Maximum Channel Count The following table shows the maximum MXW channel count available in each region. Use the spectrum scanner to view how many of these channels are available to you at your installation.
Shure Incorporated Spectrum Meter During a Scan Displays the percentage of available spectrum Radio Frequency Interference (RFI) The scanner analyzes the spectrum and divides the data into three categories: No/Low (Green) Clean RF available for MXW system. Moderate (Yellow) Some moderate interference is detected, still usable by the MXW system. High (Red) Busy RF occupied by other devices.
Shure Incorporated Conservative (More Robust) Reference this channel estimate for maximum channel stability. It includes extra usable spectrum for optimal interference avoidance, allowing multiple microphones to find available frequencies simultaneously. Aggressive (More Channels). Reference this estimate to get the most channels on air. It reserves only the minimum required extra spectrum for interfer ence avoidance.
Shure Incorporated Some applications may be outside of the range of the PHS mobile network and can benefit from use of the additional channels. To overcome PHS detection from a nearby MXW system, run a spectrum scan to find new, non-restricted frequencies. Resolving PHS Detection Errors Before you begin, use the Web Device Discovery application to confirm all APTs are online and connected to the same subnet.
Shure Incorporated Setting RF Power The RF radius of a configuration can be limited to allow another MXW system to reuse the frequency timeslots. It is best prac tice to use the lowest setting that supports the installation. Perform a walk-around test with the transmitters to ensure that the coverage setting is sufficient. The RF Power is set from the Preferences tab of the control software. The setting applies to each access point in the Configu ration.
Shure Incorporated Place the Access Point in the center of the installation for best coverage Using Multiple 2- or 4-Channel Access Points The MXW access point uses two sets of antennas to cover the operating spectrum. Each antenna set covers half of the times lots used for MXW channels. Eight-channel units use both antenna sets simultaneously; two- and four-channel units use one set at a time, operating on half of the available timeslots.
Shure Incorporated 4. Note that the APT is set to Mode A by default (Device View > RF Mode Settings > RF Coordination Mode). Close out of the window. 5. Open the Device Properties for the adjacent APT2 or APT4. 6. Set the unit to Mode B (Device Propterties > RF Mode Settings > RF Coordination Mode). 7. Select Add Updates to save the setting and close the window. 8. Make sure any additional APTs are set to alternating RF Coordination modes. 9.
Shure Incorporated Networking Networking Best Practices Use the following best practices when setting up a network to ensure reliable communication: • Always use a "star" network topology by connecting each component directly to the switch or router. • Connect networked MXW gear to the same network and set to the same subnet. This ensures best system performance and maximum microphone count. • Use only 1 DHCP server per network. Disable DHCP addressing on additional servers.
Shure Incorporated 5. Repeat for any additional components. 6. To send updates to the devices, select Apply All to the Pending Changes field of the Utility page. 7. The computer may temporarily lose connection to the control software during the updates process. When the device has been reconfigured, reopen the software using the Shure Device Discovery application. Go to Utility > Device Properties to manage the interfaces of each MXW device on the network.
Shure Incorporated Network Audio This network carries both the Dante digital audio and the control data for Dante Controller. This data is transmitted be tween the APT, the output device and the computer. The network audio requires a wired, gigabit Ethernet connection to operate. The two data types are configured differently for each MXW device. Go to Utility > Device Properties to view and edit the IP settings for MXW devices.
Shure Incorporated 4. Go to the Preferences tab. 5. Under the Network panel, change Port 4 Mode to Uplink. Managing Large Systems on a Single Network To manage large systems on a single network, lock the configuration after setting it up. This improves network performance and stability, allowing a greater number of MXW systems to operate on the same network. This is especially important if there are more than 15 total MXW APTs on a subnet.
Shure Incorporated Setting Latency Latency is the amount of time for a signal to travel across the system to the outputs of a device. To account for variances in la tency time between devices and channels, Dante has a predetermined selection of latency settings. When the same setting is selected, it ensures that all Dante devices on the network are in sync. The latency setting for Dante devices should be set according to the number of switches in the network.
Shure Incorporated Port TCP/UDP Protocol Description Factory De fault 843* tcp Flash Required for web application Open 2202 tcp ASCII Required for 3rd party control strings Open 5353 udp mDNS† Required for device discovery Open 5568 udp SDT† Required for inter-device communication Open 8023 tcp Telnet Debug console interface Password 8180* tcp Flash Required for web application Open 8181* tcp Flash Required for web application Open 8427 udp Multcast SLP† Required
Shure Incorporated 2. The Shure device will send a response packet over unicast UDP to the controller, using a destination UDP port identical to the source port of the query packet. The payload of the response packet follows this format: Bytes Content 0-3 IP address, as 32-bit unsigned integer in network order 4-7 Subnet mask, as 32bit unsigned integer in network or der 8-13 MAC address, as array of 6 bytes Note: The Shure device should respond in less than one second on a typical network.
Shure Incorporated 7. Same Subnet: Yes = The device and computer are set to the same subnet. No = The device and computer are set to different subnets. Unknown = The firmware of the device does not support this feature. Update the device firmware to view the additional connection information with this app. MXW System Control Software The MXW control software allows comprehensive system control and monitoring from a computer.
Shure Incorporated Selects the language for the GUI. This setting will be saved to the computer. ⑤ Log On Button Press the button to log onto the control software. Note: Default password is 'admin' Control Bar ① Tabs ◦ ◦ ◦ ◦ Monitor: Adjust microphone status and view RF spectrum availability.
Shure Incorporated Monitor Tab ① Access Point Selection Determines which Access Point displays on the tab. ② Density Mode Selection Displays the density mode as selected in the APT device properties. ③ Spectrum Scanner Opens the Spectrum Scanner window. See Scanning Available RF Spectrum section for more details. ④ Global Mic Control Controls the status of all microphones in the configuration (all groups made from the Configuration tab).
Shure Incorporated Selects the which microphone displays on the channel strip. Note: One microphone is on-air per channel, though an alternate microphone can be prepared in the secondary link slot. ⑦ Identify Button Commands the microphone to flash its LEDs to easily identity which device corresponds to the channel. ⑧ Microphone Status and Control View or change the microphone state: ◦ ◦ ◦ ◦ Active: On and passing audio to the network. Mute: On but the audio is muted.
Shure Incorporated Displays the microphone type. ⑯ Link/Unlink Buttons For setting up a single audio channel. Links the microphone to the primary or secondary link slot (as selected at the top of the channel strip). ◦ Link: Links the microphone from the corresponding charging slot. ◦ Unlink: Unlinks the microphone from the audio channel.
Shure Incorporated ③ Link Button Links all microphones in the charger to channels in the associated Group. ④ Configuration Lock Increases the number of MXW components that can operate on the same network. It is best practice to lock the configura tion after setup to greatly reduce network traffic from MXW equipment. When systems exceed 15 APTs on the same net work, configuration locking is required for stable performance.
Shure Incorporated Utility Tab ① Export Button Exports MXW device data to a text file (.csv). ② Configuration Filter When checked, the table displays data for only the devices that belong to the Configuration or are open for association. Uncheck the filter to view all MXW devices on the subnet. Note: The filter is checked when the configuration is locked from the Configuration tab.
Shure Incorporated The device model number. ⑥ Name Displays device name as defined in the Configuration tab or channel name as defined in the Monitor tab. ⑦ IP Address Control Displays the IP Address of the control network interface (Shure control data). ⑧ IP Address Network Audio Displays the IP Address of the Network Audio network interface (Dante digital audio data). ⑨ Battery Capacity The microphone battery's percentage of charge capacity as compared to a new battery.
Shure Incorporated APT4 Properties Window ① Device Name Device names can be customized with up to 31 characters. ② Push to Dante Name Uses the device and channel name from the MXW web interface to overwrite the names in the Dante Controller (DC) soft ware by Audinate. Note: Use with caution, as this could break the routing configuration previously made in DC, causing audio interruptions.
Shure Incorporated ④ Reboot The unit performs a power cycle. ⑤ Factory Reset Resets the device to default settings, clearing any MXW Group and Link associations. The password to access the control software will reset to admin. ⑥ Network Interface(s) View and adjust IP settings for the device's network interface(s). Network settings are different for each device. See the Networking section for configuring each MXW device.
Shure Incorporated Preferences Tab All preferences apply to each device in the Configuration. ① Switch Behavior Customize the switch on each transmitter type. ◦ ◦ ◦ ◦ Toggle (default): Press and release the button to change the status to Active or Mute. Push-to-talk: Hold button to pass audio. Push-to-mute: Hold button to mute the audio. Disabled: The button does not affect the audio.
Shure Incorporated Active Mute Solid Red Off External LED Control *Not available for MX400R series gooseneck microphones ④ Mute Preference ◦ Local Mute - Individual (default): Each transmitter is muted individually. ◦ Local Mute - All: All transmitters mute when any transmitter is muted. ◦ External Mute: Transmitter audio is on, and muted from a 3rd-party controller. ⑤ RF Power Determines the RF coverage of an access point.
Shure Incorporated Tech: Monitoring with limited editing access. Guest: Monitoring only. ⑬ Save/Load Preferences Saves the preferences of the Configuration as a file to the computer. The file can be loaded and will overwrite the settings for all devices in the Configuration. ⑭ Register the Product Link Links to Shure website for product registration.
Shure Incorporated ② Identify Button This button sends a command to the hardware to flash front-panel LEDs for easy identification. ③ Security Level Displays the access level of the user: Administrator, Technician, or Guest. ④ Log Off Logs the user out of the software. ⑤ Language Selection Selects the language for the control software interface. This setting will be saved to the computer. Inputs/Outputs Tab ① Channel Name Channel name is customizable by clicking in the text box.
Shure Incorporated ③ Firmware Version Displays the current firmware version of the device. ④ Reset Button Reboots the device with factory default settings. ⑤ Register This Product Link Click to register the device at www.shure.com to receive product and software updates. ⑥ Audio Routing Mode ◦ MXW Mode: Enables automatic channel routing when the device is a part of an MXW group (assigned from the MXW Sys tem control software).
Shure Incorporated Dante Controller Dante Controller (DC) is free software by Audinate that is used to configure and manage a network of Dante devices. Use it to route channels between Dante-enabled devices and to monitor the status of the device, clock, and network. Important: The MXWAPT must be the Dante clock master for the network. Do not change the clock master from the MXWAPT (default selection) to another device. Note: DC software is not required for routing audio within the MXW system.
Shure Incorporated Audio Problem No or distort ed audio Audio is cut ting in an out (intermittent) Indicator Network Audio LED on the Au dio Network In terface or SCM820 Solution Green Check cables Check that transmitters are on and channels are un-muted Check that the input meters are OK on the Monitor tab of the MXW control software. Attenuate if the channel is clipping. Check the output meters on the Audio Network Interface (ANI) front panel and in the ANI control software.
Shure Incorporated Network and Device Monitoring Problem Indicator Solution Device not appearing in Shure Web Device Discovery application Ensure the devices are powered Ensure PC and equipment are on the same network and set to the same subnet Turn off other network interfaces not used to connect to the device (includ ing WiFi) Check that DHCP server is functioning (if applicable) Ensure Bonjour is running on the PC If connected via Port 4 of the Audio Network Interface (ANI), ensure it is set to Swi
Shure Incorporated From the Hardware Access Point Transceiver Press and hold the recessed reset button for 10 seconds. The network audio status LED will briefly turn off to indicate the unit is rebooting. CAUTION: A factory reset deletes all Group associations and microphone Links saved in the device. Audio Network Interface Press and hold the reset button for 10 seconds. The front panel LEDs will flash to indicate the unit is rebooting. Networked Charging Station 1. 2. 3. 4. Turn off the power switch.
Shure Incorporated Accessories and Model Variations MXW Device Access Point Transceiver Description Part Number 8-Channel Access Point Transceiver MXWAPT8 4-Channel Access Point Transceiver MXWAPT4 2-Channel Access Point Transceiver MXWAPT2 Mounting Plate 65A20096 Paintable Cover 65A20030 8-Channel Audio Network Interface MXWANI8 4-Channel Audio Network Interface MXWANI4 Hardware Kit 90A20081 IEC Cable Varies by region; see table 8-Channel Audio Network Interface MXWNCS8 4-Channel A
Shure Incorporated MXW Device Description Gooseneck Base Part Number Black MXW gooseneck base trans mitter (without gooseneck micro phone) MXW8 White MXW gooseneck base transmitter (without gooseneck microphone) MXW8W Gooseneck microphone see table Battery SB901A USB Charger Varies by region; see table Mono Earpiece/Volume Control DH 6125+VC Anti-Roll Ring for MXW2 A1K Lavalier Options Microphone Description Part Number ® Microflex 5mm Subminiature Lavalier, Omnidirectional, Black ®
Shure Incorporated Microphone Description Light ring indicator Polar Pattern Length Part Number Supercardioid 10" (25.4 cm) MX410LP/S Cardioid 15" (38.1 cm) MX415LP/C Supercardioid 15" (38.1 cm) MX415LP/S 5" (12.7 cm) MX405RLP/N 10" (25.4 cm) MX410RLP/N 15" (38.1 cm) MX415RLP/N Cardioid for any length R185B Supercardioid for any length R184B 5" (12.7 cm) MX405WLP/N 10" (25.4 cm) MX410WLP/N 15" (38.1 cm) MX415WLP/N 5" (12.7 cm) MX405WRLP/N 10" (25.
Shure Incorporated USB Charger USB Charger by Region Part Number USA SBC10-USB-A UK SBC10-USBUK-A Europe SBC10-USBE-A Australia SBC10-USBAZ-A Japan and Taiwan SBC10-USBJTW-A Brazil SBC10-USBR-A India SBC10-USBIN-A Microflex Wireless Specifications System RF Carrier Frequency Range Band Region Frequency Range Z10 USA , Canada , Mexico 1920– 1930 MHz Z11 Europe , Asia , Middle-East 1880– 1900 MHz Z12 Japan 1893– 1905 MHz Z15 Taiwan 1880– 1895 MHz Z14 Brazil 1910– 1920 MHz Au
Shure Incorporated Signal-to-Noise Ratio <90 dB Aweighted Cable Requirements Cat 5e or higher Dimensions 61 x 150 x 168 mm Weight 650 g Operating Temperature Range 5℃ (41℉) - 40℃ (104℉) Transmitters Gain Adjustment Range −25 to +15 dB (in 1 dB steps) Maximum Input Level Mic gain @ −16 dB −9 dBV Headphone Output 3.5 mm (1/8"), dual mono (will drive stereo phones) Maximum Headphone Output Power 1kHz @ 1% distortion, peak power, @16Ω 17.
Shure Incorporated Housing Molded Plastic Recommended Storage Temperature Range 0°C (32°F) to 25°C (77°F) MXW1 Hybrid Bodypack Transmitter Microphone Connector 4-Pin male mini connector (TA4M), See drawing for details Input Impedance @ 1 kHz >20 kΩ Internal Microphone Omnidirectional (20 Hz – 20 kHz) Dimensions 22 mm x 45 mm x 99 mm (0.9 in. x 1.8 in. x 3.9 in.) H x W x D Weight 85 g (3.0 oz.
Shure Incorporated MXW6 Boundary Transmitter Microphone Capsule MXW6/O R183B MXW6/C R185B Dimensions 23 mm x 44 mm x 114 mm (0.9 in. x 1.75 in. x 4.5 in.) H x W x D Weight 108 g (3.8 oz.) with batteries MXW8 Gooseneck-Base Transmitter Microphone Connector 6-pin connector for Shure MX405/10/15 Configuration Unbalanced Input Impedance @ 1 kHz >20 kΩ Gooseneck Options See accessories list Dimensions 36 mm x 71 mm x 124 mm (1.4 in. x 2.8 in. x 4.9 in.) H x W x D Weight 193 g (6.8 oz.
Shure Incorporated Antenna Type Internal, Spatial Diversity, Circular Polarization Antenna Gain Average 0.5 dBi Peak 3.0 dBi Housing Molded Plastic, Cast Zinc Dimensions 24 mm x 170 mm x 170 mm (1.35 in. x 6.7 in. x 6.7 in.), H x W x D Without mounting plate or cover Weight APT8 856 g (1.9 lbs) APT2, APT4 845 g (1.9 lbs) Paintable Cover 85 g (0.2 lbs) Mounting Bracket 68 g (0.
Shure Incorporated NCS4 1.7 kg (3.7 lbs) NCS2 0.8 kg (1.8 lbs) Audio Network Interface (ANI) Audio Network Interface (ANI) Audio Frequency Response 20 Hz to 20 kHz (+1, −1.5 dB) Dynamic Range 20 Hz to 20 kHz, A-weighted, typical Analog-to-Dante 113 dB Dante-to-Analog 110 dB Output Noise 20 Hz to 20 kHz, A-Weighted, typical Line Aux Mic −84.5 dBV −95.2 dBV −106.5 dBV THD+N 20 Hz to 20 kHz +4dBu analog input, −10 dBFS digital input <0.
Shure Incorporated Analog Connections Outputs Clipping Level (minimum) Configuration Active Balanced Impedance 310 Ω Line Aux Mic +26.2 dBV +16.2 dBV −3.8 dBV Input(s) Clipping Level (minimum) Configuration Active Balanced Impedance 10.6 kΩ Line Aux +23.8 dBV +10.8 dBV Headphone Output 6.35 mm (1/4") TRS, 100 mW, 350 Ω, dual mono (will drive stereo phones) 0 dBV=1 V RMS 0 dBu=0.775 V RMS 0 dBV=2.
Shure Incorporated Network Addressing Capability DHCP, link-local, static Transmitter Output Power Bands: Z10, Z11, Z14, Z15 MXW1 Setting dBm mW Low -2 1 Medium 5 3 High 12 16 Maximum 17 50 Setting dBm mW Low 0 1 Medium 7 5 High 12 16 Maximum 17 50 Setting dBm mW Low -2 1 Medium 5 3 High 12 16 Maximum 19 80 MXW2 MXW6, MXW8 Band: Z12 MXW1, MXW6, MXW8 Setting dBm mW Low 0 1 Medium 5 3 High 9 8 98/102
Shure Incorporated Maximum 12 16 MXW2 Setting dBm mW Low 0 1 Medium 7 5 High 9 8 Maximum 12 16 Wiring Diagram TA4M Connector Audio Network Interface (ANI) 99/102
Shure Incorporated Safety Information SAFETY PRECAUTIONS The possible results of incorrect use are marked by one of the two symbols—"WARNING" and "CAUTION"—depending on the imminence of the danger and the severity of the damage. WARNING: Ignoring these warnings may cause severe injury or death as a result of incorrect operation. CAUTION: Ignoring these cautions may cause moderate injury or property damage as a result of incor rect operation.
Shure Incorporated Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment. Please follow your regional recycling scheme for batteries, packaging, and electronic waste. Note: This device is not intended to be connected directly to a public internet network. Information to the user This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Shure Incorporated 2. This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; 2.
