User's Manual

ManualsBrandsShure ManualsAudio ConferencingMXW2 Handheld Transmitter with Beta 58A Microphone Capsule

Table Of Contents

Table of Contents
MXW Microflex® Wireless
IMPORTANT SAFETY INSTRUCTIONS
Overview
Overview
- General Description
- Features
  - Legendary Shure Quality
  - Advanced Networking and Control
- MXW Wireless System
  - Components of the MXW System
  - System Design and Technology
Hardware Description
- Audio Network Interface (ANI)
  - Front Panel
  - Back Panel
- Access Point Transceiver (APT)
  - Model Variations
  - Directional Antennas
- Networked Charger (NCS)
  - Model Variations
  - Connecting Microphones
- Microphone Transmitters
  - Description
    - Status LED Table
  - Microphone Transmitters
- Rechargeable Batteries
Installation
- Additional Equipment
- Connecting MXW Components
  - Single Group System (1 Access Point)
  - Multiple Group System (>1 Access Point)
    - Large Single-Room Installation
    - Local System Star Setup
- Rack Installation
- Securing the Charging Station
- Two-Channel Charger Wall Mount
  - Installation
  - NCS2 Mount Dimensions
- Mount the Access Point Transceiver
- Power the Hardware
  - Fully Charge the Transmitters
    - Battery Charge Times
      - Approximate Charge Times
- Open the MXW Control Software
  - Operating System Requirements
System Set Up
System Set Up
- Group Devices to Form Audio Channels
- Channel Routing between Devices
  - Charging Station Examples
  - Audio Output Examples
    - 8-Channel Group
    - 4-Channel Group
- Link Microphones to Group Channels
- Preparing a Backup Microphone
  - One Active Mic per Channel
  - Procedure
- Exchanging or Removing a Component
  - Exchanging a Transmitter
  - Remove a Device from a Group
- Link a Microphone Over the Network
Large Installations
- Shure SystemOn Software For Managing Large Systems
- High Density Mode
  - Density Mode Comparison
  - Setting the Density Mode
- Configurations: Managing Multiple Groups
  - Primary Access Point
  - Creating Separate Configurations
Wireless Management
- Overview of Channel Coordination
  - Maximum Channel Count
- Scanning Available RF Spectrum
  - Performing a Scan
- PHS Detection
  - Excluding PHS Bands
- Identifying PHS Detection Errors
  - Resolving PHS Detection Errors
    - Running Spectrum Scans
- Setting RF Power
  - RF Power Levels
- Using Multiple 2- or 4-Channel Access Points
  - Requirements
  - Set Up
Networking
Networking
- Networking Best Practices
- Configuring IP Settings
  - Network Audio and Shure Control Data
    - Network Settings for Each MXW Device
  - Manually Assigning Static IP Address
- Advanced Setup
Software
- MXW System Control Software
- Control Software for the MXW Audio Network Interface
- Dante Software by Audinate
- Firmware Updates
  - Firmware Release Requirements
Troubleshooting
- Audio
- System Setup and MXW Groups
- Network and Device Monitoring
- Additional Resources
- Factory Reset
  - From the Hardware
  - From the Control Software
Accessories and Model Variations
- Lavalier Options
- Gooseneck Options
- IEC Power Cable
- USB Charger
Microflex Wireless Specifications
Microflex Wireless Specifications
- System
- Transmitters
- Access Point Transceiver (APT)
- Networked Charging Station (NCS)
- Audio Network Interface (ANI)
- Transmitter Output Power
  - Bands: Z10, Z11, Z14, Z15
  - Band: Z12
    - MXW1, MXW6, MXW8
    - MXW2
- Wiring Diagram
  - TA4M Connector
  - Audio Network Interface (ANI)
Safety Information
- SAFETY PRECAUTIONS
- WARNING
- WARNING
Important Product Information
- Information to the user
Certifications
- Trademarks

Shure Incorporated

16/97

Model Variations

MXWNCS8

Accepts eight boundary, bodypack, or handheld microphones

or four gooseneck bases

MXWNCS4

Accepts four boundary, bodypack, or handheld microphones

or two gooseneck bases

MXWNCS2

Accepts two boundary, bodypack, or handheld microphones.

MXW8 Gooseneck bases are not supported on this charger

① Charging Slots (USB 3.0 Type A)

Recharge and link microphones by connecting them to the USB slots on the charger. When the charger is associated to a

group, the slots are mapped to access point channels (See Audio Channel Assignment for details).

Note: Any microphone can charge in any charger, regardless of Group association or network connection.

② Power LED

Illuminates green when the unit is powered on.

③ Microphone Link LED

Indicates the status of the Linking procedure:

Color Indicator

Off (default) No Link has been initiated.

Flashing Green Link procedure is in process.

Green Microphones have been successfully linked to channels.

Red

Linkprocedureunsuccessful(RFissue,networkfailure,ormicrophonesremovedduringpro

cedure)

Amber Link procedure cannot start because the station is not associated to a group.