User's Manual

ManualsBrandsShure ManualsAudio ConferencingMXW2 Handheld Transmitter with Beta 58A Microphone Capsule

Table Of Contents

Table of Contents
MXW Microflex® Wireless
IMPORTANT SAFETY INSTRUCTIONS
Overview
Overview
- General Description
- Features
  - Legendary Shure Quality
  - Advanced Networking and Control
- MXW Wireless System
  - Components of the MXW System
  - System Design and Technology
Hardware Description
- Audio Network Interface (ANI)
  - Front Panel
  - Back Panel
- Access Point Transceiver (APT)
  - Model Variations
  - Directional Antennas
- Networked Charger (NCS)
  - Model Variations
  - Connecting Microphones
- Microphone Transmitters
  - Description
    - Status LED Table
  - Microphone Transmitters
- Rechargeable Batteries
Installation
- Additional Equipment
- Connecting MXW Components
  - Single Group System (1 Access Point)
  - Multiple Group System (>1 Access Point)
    - Large Single-Room Installation
    - Local System Star Setup
- Rack Installation
- Securing the Charging Station
- Two-Channel Charger Wall Mount
  - Installation
  - NCS2 Mount Dimensions
- Mount the Access Point Transceiver
- Power the Hardware
  - Fully Charge the Transmitters
    - Battery Charge Times
      - Approximate Charge Times
- Open the MXW Control Software
  - Operating System Requirements
System Set Up
System Set Up
- Group Devices to Form Audio Channels
- Channel Routing between Devices
  - Charging Station Examples
  - Audio Output Examples
    - 8-Channel Group
    - 4-Channel Group
- Link Microphones to Group Channels
- Preparing a Backup Microphone
  - One Active Mic per Channel
  - Procedure
- Exchanging or Removing a Component
  - Exchanging a Transmitter
  - Remove a Device from a Group
- Link a Microphone Over the Network
Large Installations
- Shure SystemOn Software For Managing Large Systems
- High Density Mode
  - Density Mode Comparison
  - Setting the Density Mode
- Configurations: Managing Multiple Groups
  - Primary Access Point
  - Creating Separate Configurations
Wireless Management
- Overview of Channel Coordination
  - Maximum Channel Count
- Scanning Available RF Spectrum
  - Performing a Scan
- PHS Detection
  - Excluding PHS Bands
- Identifying PHS Detection Errors
  - Resolving PHS Detection Errors
    - Running Spectrum Scans
- Setting RF Power
  - RF Power Levels
- Using Multiple 2- or 4-Channel Access Points
  - Requirements
  - Set Up
Networking
Networking
- Networking Best Practices
- Configuring IP Settings
  - Network Audio and Shure Control Data
    - Network Settings for Each MXW Device
  - Manually Assigning Static IP Address
- Advanced Setup
Software
- MXW System Control Software
- Control Software for the MXW Audio Network Interface
- Dante Software by Audinate
- Firmware Updates
  - Firmware Release Requirements
Troubleshooting
- Audio
- System Setup and MXW Groups
- Network and Device Monitoring
- Additional Resources
- Factory Reset
  - From the Hardware
  - From the Control Software
Accessories and Model Variations
- Lavalier Options
- Gooseneck Options
- IEC Power Cable
- USB Charger
Microflex Wireless Specifications
Microflex Wireless Specifications
- System
- Transmitters
- Access Point Transceiver (APT)
- Networked Charging Station (NCS)
- Audio Network Interface (ANI)
- Transmitter Output Power
  - Bands: Z10, Z11, Z14, Z15
  - Band: Z12
    - MXW1, MXW6, MXW8
    - MXW2
- Wiring Diagram
  - TA4M Connector
  - Audio Network Interface (ANI)
Safety Information
- SAFETY PRECAUTIONS
- WARNING
- WARNING
Important Product Information
- Information to the user
Certifications
- Trademarks

Shure Incorporated

97/97

The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact

information please visit www.shure.com

The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance

Authorized European representative:

Shure Europe GmbH

Headquarters Europe, Middle East & Africa

Department: EMEA Approval

Jakob-Dieffenbacher-Str. 12

75031 Eppingen, Germany

Phone: +49-7262-92 49 0

Fax: +49-7262-92 49 11 4

Email: info@shure.de

Authorized under the FCC verification provision per Part 15b.

Industry Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B)

Note: See the label located on the bottom side of the charger enclosure for the FCC marking, the CE marking, the RCM marking, and the electrical ratings.

Certified under FCC Part 15.

FCC: DD4MXW1, DD4MXW2, DD4MXW6, DD4MXW8, DD4MXWAPT4, DD4MXWAPT8.

Meets applicable requirements of RSS-213.

IC: 616A-MXW1, 616A-MXW2, 616A-MXW6, 616A-MXW8, 616A-MXWAPT4, 616A-MXWAPT8.

Trademarks

Audinate , the Audinate logo and Dante are trademarks of Audinate Pty Ltd.