QLX-D Wireless System Shure QLXD wireless system user guide. Includes dimensions, frequency bands, error codes, and more.
Shure Incorporated Table of Contents QLX-DWireless System 4 IMPORTANT SAFETY INSTRUCTIONS 4 WARNING 5 Important Product Information 5 LICENSING INFORMATION 6 Information to the user 6 Australia Warning for Wireless 6 System Overview 6 Features 7 System Components 7 Quick Start 9 Step 1: Power and Antenna Connection 9 Step 2: Scanning for the Best Available Channel 9 Step 3: Install Batteries into Transmitter 10 Step 4: IR Sync to Create an Audio Channel 10 Step 5: Sound Check
Shure Incorporated Downloading and Updating Firmware 37 QLXD4 50 Updating the Receiver 37 QLXD1 51 Updating the Transmitter 37 QLXD2 52 Receiver Output Connectors 54 TA4M Input Connector Diagram 54 Frequency Range and Transmitter Output Power 54 Troubleshooting Error Codes and Solutions Single and Dual Rackmount Assembly 38 40 40 Securing the AC Power Cord 41 Installing Footpads 42 Accessories Optional Accessories Specifications Frequencies for European Countries 56 Certification
Shure Incorporated QLX-D Wireless System IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. READ these instructions. KEEP these instructions. HEED all warnings. FOLLOW all instructions. DO NOT use this apparatus near water. CLEAN ONLY with dry cloth. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturer’s instructions.
Shure Incorporated Caution: risk of electric shock Caution: risk of danger (See note.) Direct current Alternating current On (Supply) Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION Stand-by Equipment should not be disposed of in the normal waste stream WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel.
Shure Incorporated Important Product Information LICENSING INFORMATION Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment.
Shure Incorporated software compatibility for advanced frequency coordination. AES-256 encryption comes standard and can be easily enabled for secure wireless transmission. QLXD also adds Shure rechargeable power options to provide dramatic longterm cost savings and extended transmitter bat tery life over alkaline batteries, and battery metering that reports remaining runtime in hours and minutes.
Shure Incorporated ④ 2 ft. BNC Cables with Bulkhead Adapters (2) ⑤ Choice of QLXD1 Bodypack Transmitter or QLXD2 Handheld Transmitter ⑥ AA Alkaline Batteries (not included in Argentina) ⑦ Rackmount Hardware Model Variations Model variations with additional components are available to meet specific performance situations.
Shure Incorporated • Zipper Bag (2) Quick Start Step 1: Power and Antenna Connection ① Connect an antenna to each of the antenna connectors. ② Connect the power supply to the receiver and plug into an AC power source. ③ Connect the receiver audio output to a mixer or amplifier. ④ Press and hold the power button to turn on the receiver. Step 2: Scanning for the Best Available Channel 1. Press the menu button on the receiver to access the scan function. 2. Press the enter button to start a frequency scan.
Shure Incorporated Step 3: Install Batteries into Transmitter ① Accessing the Battery Compartment Press the side tabs on the bodypack or unscrew the cover on the handheld as shown to access the battery compartment.
Shure Incorporated Note: If the IR sync fails, repeat the IR sync procedure, carefully maintaining alignment between the IR windows of the transmitter and receiver. Step 5: Sound Check and Gain Adjustment 1. Test the transmitter at performance levels while monitoring the audio meter and the audio LED. The audio meter should display at least 3 bars and the audio LED should be green. Reduce the gain if there is audible distortion of the audio. 2.
Shure Incorporated Hardware Interface Receiver Front and Back Panels ① Display Shows menu options, receiver and transmitter settings. ② Arrow Buttons Adjust gain setting or change menu parameters. ③ Enter Button Press to save menu or parameter changes. ④ Sync Button Press to activate IR sync. ⑤ Power Switch Powers receiver on or off.
Shure Incorporated ⑩ Sync LED ◦ Blinking: IR sync mode is enabled ◦ On: Receiver and transmitter aligned for IR sync ⑪ Power Cord Strain Relief Secures power cord. ⑫ Power Supply Jack Connection point for DC power supply. ⑬ Ethernet Port For network connection. ◦ Amber LED (network speed): off = 10 Mbps, on = 100 Mbps ◦ Green LED (network status): off = no network link, on = network link active flashing = rate corresponds to traffic volume ⑭ Receiver Reset Press to restore receiver default settings.
Shure Incorporated ⑱ 1/4" Instrument/Auxiliary Output Impedance Balanced (Tip: audio, Ring: no audio, Sleeve: ground) Receiver Display ① Group Displays group setting. ② Channel Displays channel setting. ③ Active Antenna Indicator Illuminates to indicate which antenna is active. ④ RF Signal Meter Number of bars displayed corresponds to RF signal level - OL = overload. ⑤ Audio Meter Number of bars displayed corresponds to audio level.
Shure Incorporated Illuminates when encryption is enabled. ⑩ Scan Displayed when scan function is active. ⑪ Network Scan Displayed when network scan function is active in multi-receiver systems. ⑫ Network Connection Indicator Illuminates when additional Shure components are detected on the network. ⑬ TV Channel Displays the number of the TV channel containing the selected frequency. ⑭ Transmitter Battery Icon Indicates remaining battery life.
Shure Incorporated Edit the receiver group settings ④ Channel Edit the receiver channel settings ⑤ Lock Choose a control lock option ⑥ Encryption Use the arrow buttons to enable encryption (on) or disable encryption (off) ⑦ Frequency Use the arrow buttons to edit the frequency value Advanced Menu Starting from the main menu home screen, press menu while holding the enter button to access the advanced menu.
Shure Incorporated ⑥ IP Settings Use to select and edit IP settings and subnet masks ⑦ Network Reset Returns network settings and IP address to default setting ⑧ Factory Reset Restores factory settings For application and configuration details, see the related guide topic for each advanced feature.
Shure Incorporated Secures batteries when powering transmitter with AA batteries instead of Shure SB900 battery. ⑧ Bodypack Antenna For RF signal transmission. ⑨ Handheld Integrated Antenna For RF signal transmission. ⑩ Microphone Cartridge See Optional Accessories for a list of compatible cartridges. ⑪ TA4M Input Jack Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable.
Shure Incorporated Transmitter Display ① Battery Indicator Bars displayed indicate remaining battery life. ② Home Screen Display: Group and Channel/Frequency/SB900 Battery Runtime Use the arrow keys to select one of the following home screen displays: Group and Channel SB900 battery runtime Frequency ③ Encryption Status Icon displayed when encryption is enabled. ④ Lock Displayed when transmitter controls are locked. ⑤ RF Power RF power setting (Lo or Hi).
Shure Incorporated Transmitter controls • To increase, decrease or change a parameter, use the ▼▲ buttons • To save a menu change, press enter • To exit a menu without saving a change, press the menu button Bodypack Handheld Transmitter Menu Options and Navigation The transmitter features individual menu screens for setting up and adjusting the transmitter. To access the menu options from the home screen, press the menu button. Each additional press of the menu button advances to the next menu screen.
Shure Incorporated ⑥ rf power Select an rf power setting: ◦ Lo = 1 mW ◦ Hi = 10 mW ⑦ mic offset dB Use to match audio levels between two transmitters used in a combo system. Range is 0 to 21 dB (3 dB increments). Ad justments occur in realtime. ⑧ battery type Use to set the battery type to match the installed AA battery type to ensure accurate battery metering. Menu is not dis played when Shure SB900 batteries are installed.
Shure Incorporated Locking and Unlocking the Receiver Controls The receiver has the following control lock options which can be used separately or in any combination: • gain: locks the arrow buttons to prevent changes to the audio gain settings • menu: prevents access to menu items and IR sync (gain controls and power switch remain active) • power: disables power switch (gain and menu controls remain active) To lock a receiver control: 1. Press the menu button to navigate to the lock settings. 2.
Shure Incorporated Battery Installation ① Accessing the Battery Compartment Press the side tabs on the bodypack or unscrew the cover on the handheld as shown to access the battery compartment.
Shure Incorporated AA Battery Installation Fully insert the batteries as shown to ensure proper battery contact and to allow the door to latch securely. Shure SB900 Rechargeable Battery Shure SB900 lithium-ion batteries offer a rechargeable option for powering the QLX-D transmitters. Batteries quickly charge to 50% capacity in one hour and reach full charge within three hours. Single chargers and multiple bay chargers are available to recharge the Shure batteries.
Shure Incorporated Color Status Green Charging Complete Amber Flashing Fault: check connections and battery Off No battery in bay Multiple Bay Chargers Shure offers two models of multiple bay chargers: • SBC-200 two bay charger • SBC-800 eight bay charger Multiple bay chargers can charge individual batteries or batteries installed in transmitters. 1. Plug the charger into an AC power source. 2. Insert batteries or transmitters into the charging bay. 3.
Shure Incorporated • During storage, check batteries every 6 months and recharge to 40% of capacity as needed Low Battery Alert The receiver display can be configured to flash when the battery runtime for a transmitter is less than 30 minutes.
Shure Incorporated and receivers that share an encryption key form a protected audio path, preventing unauthorized access by other receivers. To maintain security, components remain encrypted when turned off and on. Creating an Encrypted Audio Channel 1. Press the menu button to navigate to the encryption menu, indicated by the key icon. 2. Use the arrow buttons to select an encryption option: ◦ on = encryption enabled ◦ OFF = encryption disabled 3. Press enter to save.
Shure Incorporated System Set Up Creating Audio Channels A wireless audio channel is formed when a receiver and transmitter are tuned to the same frequency. To ease setup, frequen cies available to the QLX-D system are organized into groups and channels. Each group contains a number of channels, and each channel is assigned to a specific preset frequency.
Shure Incorporated 6. Press enter to deploy the frequencies or press menu to cancel the deployment. 7. The front panel LEDs on each receiver will blink when a deployed frequency has been assigned. Note: Full frequency deployment may not occur if the number of receivers in the network exceeds the number of available frequencies in the selected group. Try another group or rescan after turning off unused receivers.
Shure Incorporated Manual Frequency Selection Manual frequency selection can be used instead of groups and channels to set the transmitter and receiver to a specific fre quency. For example, an audio channel can be created by setting the receiver and transmitter to same frequency. Setting the Receiver Frequency 1. Press menu to navigate to the frequency setting option. 2. Use the arrow buttons to adjust the frequency. Press and hold for faster scrolling. 3. Press enter to save.
Shure Incorporated Matching Audio Levels with Mic Offset When linking two transmitters to a receiver, there may be a difference in volume levels between microphones or instruments. If this occurs, use the Mic Offset function to match the audio levels and eliminate audible volume differences between transmit ters. If using a single transmitter, set Mic Offset to 0 dB. 1. Turn on the first transmitter and perform a sound check to test the audio level. Turn off the transmitter when finished. 2.
Shure Incorporated Shure AXT600 Spectrum Manager Compatibility QLXD receivers are compatible with the Axient AXT600 Spectrum Manager. Networked receivers will appear in the device in ventory and frequencies from the Compatible Frequency List can be deployed and monitored by the Spectrum Manager. For more information regarding the Spectrum Manager, see the Axient System Guide.
Shure Incorporated Custom Groups Specific channels and frequencies can be selected and placed into custom groups. Custom groups are commonly used to as sign networked receivers to a specific range of frequencies or to pre-configure receivers for rental applications. Once a custom group has been created, it can be loaded to the receiver using the group menu. When network scan is used to assign frequencies from a receiver with a custom group selected, all of custom groups (U1, U2, U3, etc...
Shure Incorporated Transmitter IR Sync from a Custom Group To ensure accurate display of group and channel information, IR sync the transmitter from the Custom Group menu screen: 1. 2. 3. 4. Press menu while holding the enter button to access the Custom Group screen. Turn on the transmitter and press the sync button on the receiver. Align the IR sync windows of the transmitter and receiver. sync good appears on the display when IR sync is complete.
Shure Incorporated • Use multiple Ethernet switches to extend the network for larger installations Network Troubleshooting • • • • Use only one DHCP server per network All devices must share the same subnet mask All receivers must have the same level of firmware revision installed Look for the illuminated network icon on the front panel of each device: If the icon is not illuminated, check the cable connection and the LEDs on the Ethernet port.
Shure Incorporated 6. When group 4 has been edited, the display will show the subnet mask menu. Use the arrow buttons to scroll and select a preset value for each of the subnet mask groups. 7. When finished, press enter to save settings. Note: To restore automatic DHCP IP addressing, enter the IP menu and select AU (automatic). The Network Reset menu option can also be used to restore DHCP addressing. Wireless Workbench 6 1. 2. 3. 4. Open the Channel Properties tab in WWB6.
Shure Incorporated Firmware Updates Firmware is embedded software in each component that controls functionality. Periodically, new versions of firmware are devel oped to incorporate additional features and enhancements. Firmware Versioning When updating receiver firmware, update transmitters to the same firmware version to ensure consistent operation. The firmware version is numbered in the form of MAJOR.MINOR.PATCH (e.g., 1.2.14).
Shure Incorporated 2. The receiver displays the type of transmitter firmware it has available. The receiver holds one type of firmware at a time. ◦ HH BP = handheld or bodypack firmware ◦ BN GN = gooseneck or boundary firmware 3. Press enter to start the update. 4. When the red IR LED flashes, align the receiver and transmitter IR sync ports. The red LED will remain illuminated to indicate correct alignment and the download will automatically start. 5.
Shure Incorporated Adjust the system gain on the front of the receiver. Ensure the mic/line switch setting (XLR output only) on the back of the re ceiver corresponds to the input of the mixing console, amplifier, or processor. Cables Check that all cables and connectors are fully engaged or locked into position. Inspect cables for damage. Replace if neces sary. Interface Locks The transmitter and the receiver can be locked to prevent accidental or unauthorized changes.
Shure Incorporated ◦ Eliminate RF overload (see below).
Shure Incorporated Single and Dual Rackmount Assembly Securing the AC Power Cord 41/61
Shure Incorporated Installing Footpads Accessories Optional Accessories Batteries and Chargers Shure Lithium-Ion Rechargeable Battery SB900 8-Pack Shure Lithium-Ion Rechargeable Batteries SB900-8 8-Bay Shure Battery Charger SBC800-US Dual Docking Charger With PS45US Power Supply SBC200-US Dual Docking Charger, Power Supply Not Included SBC200 Single Battery Charger SBC100 Axient Charging Module SBC-AX 2-Bay Portable Battery Charger With PS50US Power Supply SBC210 Bodypack Power Insert SBC
Shure Incorporated Active Antenna Splitters Antenna Distribution System UA845 E Antenna Distribution System UA845 E "B" Antenna Distribution System UA845J Antenna UHF-R 470-952 MHz UA845-SWB Antenna,Power Dist UHF-R 470-952 MHz UA845-SWB-AZ Antenna UHF-R 470-952 MHz UA845-SWB-BR Antenna,Power Dist UHF-R 470-952 MHz UA845-SWB-C Antenna,Power Dist UHF -R 470-952 MHz UA845-SWB-E Antenna UHF-R 470-952 MHz UA845-SWB-K Antenna, Power Dist UHF-R 470-952 MHz UA845US UHF Antenna Power Distributi
Shure Incorporated UABIAST-K UABIAST-J UABIAST-AZ UABIAST-TW In-Line Amplifiers and Antennas In-Line Antenna Amplifier, 792-810 MHz UA830A In-Line Antenna Amplifier, 470-698MHz UA830USTV In-Line Antenna Amplifier, 500-900 MHz UA830WB In-Line Antenna Amplifier UA830X Active Directional Antenna 470-790MHZ UA874E Active Directional Antenna 470-698MHZ UA874US Active Directional Antenna 470-900MHZ UA874WB Active Directional Antenna 925-952MHZ UA874X Directional Wideband Antenna for PSM Systems
Shure Incorporated Coaxial Cable, BNC-BNC, RG213/U TYPE, 50 OHM, 100 FT Length (30 M) UA8100 Ethernet Jumper Cable, 8" C8006 Ethernet Cable, 3 FT. C803 Ethernet Cable, 10 FT. C810 Ethernet Cable, Ruggedized, 100 FT. C8100 Ethernet Cable, Ruggedized, 25 FT. C825 Ethernet Cable, Ruggedized, 50 FT.
Shure Incorporated Cable, Instrument, 2-foot (0.7m), 4-pin Mini Connector (TA4F) with Right-Angle 1/4-inch Connector, used with Shure Wireless Bodypack Transmitters WA304 Premium Guitar Cable TQG Threaded Connector WA305 Premium Guitar Cable TQG Latching Connector WA306 Cable, Microphone, 4-foot (1.3m), 4-pin Mini Connector (TA4F) to XLR Connector (F), used with Shure Bodypack Transmitters. WA310 In-line audio mute switch for Shure wireless bodypack transmitters with a TA4F connector.
Shure Incorporated 6 foot (1.8m) BNC to BNC Coaxial Cable for Remote Antenna Mounting for ULX Wireless System UA806 25 ft. BNC-BNC Coaxial Cable UA825 50 ft. BNC-BNC Coaxial Cable UA850 100 ft.
Shure Incorporated UHF Antenna Power Distribution System UA844SWB/LC-AR UHF Antenna Power Distribution System UA844SWB/LC-BR UHF Antenna Power Distribution System UA844SWB/LC-AZ UHF Antenna Power Distribution System UA844SWB/LC-C UHF Antenna Power Distribution System UA844SWB/LC-E UHF Antenna Power Distribution Amplifier UA844SWB/LC-J UHF Antenna Power Distribution Amplifier UA844SWB/LC-K UHF Antenna Power Distribution Amplifier UA844SWB/LC-UK Active Antenna Splitters Antenna Distribution S
Shure Incorporated Black Bodypack Pouch WA582B Specifications RF Carrier Frequency Range 470–937.5 MHz, varies by region (See Frequency Range and Output Power table) Working Range 100 m (328 ft) Note: Actual range depends on RF signal absorption, reflection and interference. RF Tuning Step Size 25 kHz, varies by region Image Rejection >70 dB, typical RF Sensitivity -97 dBm at 10-5 BER Latency <2.
Shure Incorporated Storage Temperature Range -29°C (-20°F) to 74°C (165°F) Note: Battery characteristics may limit this range. Battery Life SB900A alkaline 1/10 mW 1/10 mW 470 to 865 >9:30 hours 8 hours 902 to 928 >8:30 hours >6 hours 174 to 216 >9:30 hours >8:30 hours 1240 to 1800 >8:00 hours >6 hours QLXD The values in this table are typical of fresh, high quality batteries. Battery runtime varies depending on the manufacturer and age of the battery.
Shure Incorporated Configuration 1/4" (6.35 mm) Impedance balanced (Tip=audio, Ring=no audio, Sleeve=ground) XLR balanced (1=ground, 2=audio +, 3=audio −) Impedance 1/4" (6.35 mm) 100 Ω (50 Ω Unbalanced) XLR 100 Ω Full Scale Output 1/4" (6.35 mm) +12 dBV XLR LINE setting= +18 dBV, MIC setting= -12 dBV Mic/Line Switch 30 dB pad Phantom Power Protection 1/4" (6.
Shure Incorporated Housing Cast aluminum Audio Input Connector 4-Pin male mini connector (TA4M), See drawing for details Configuration Unbalanced Impedance 1 MΩ, See drawing for details Maximum Input Level 1 kHz at 1% THD 8.5 dBV (7.
Shure Incorporated Battery Type Shure SB900 Rechargeable Li-Ion or AA batteries 1.5 V Dimensions 269 mm x 51 mm (10.6 in. x 2.0 in.) L x Dia. Weight 307 g (12.1 oz.
Shure Incorporated Receiver Output Connectors TA4M Input Connector Diagram ① Ground ② Bias Voltage ③ Audio Input ④ Ground Frequency Range and Transmitter Output Power Power ( mW RMS )* Band Frequency Range (MHz) G50 470 to 534 1 / 10 G51 470 to 534 1 / 10 G52 479 to 534 1 / 10 G62 510 to 530 1 / 10 H50 534 to 598 1 / 10 H51 534 to 598 1 / 10 H52 534 to 565 1 / 10 (Lo/Nm/Hi) 54/61
Shure Incorporated Power ( mW RMS )* Band Frequency Range (MHz) H53 534 to 598 1 / 10 J50 572 to 636 1 / 10 J51 572 to 636 1 / 10 JB 806 to 810 1 / 10 K51 606 to 670 1 / 10 K52 606 to 670 1 / 10 L50 632 to 696 1 / 10 L51 632 to 696 1 / 10 L52 632 to 694 1 / 10 L53 632 to 714 1 / 10 M19 694 to 703 (Thailand) 1 / 10 P51 710 to 782 1 / 10 P52 710 to 782 1 / 10 Q12 748 to 758 (Thailand) 1 / 10 Q51 794 to 806 10 S50 823 to 832, 863 to 865 1 / 10 V50 174 to 216
Shure Incorporated Note: Frequency bands might not be available for sale or authorized for use in all countries or regions. For the band Z17 (1492-1525 MHz), it must be used indoors only. For the Band Z19 (17851800MHz) used in Australia, per Radio Communications Low Interference Potential Devices Class Li cense 2015; item 30 note C: the system must be operated within the range of 1790-1800MHz when used outdoors. เครื่องโทรคมนาคมและอุปกรณ์นี้มีความสอดคล้องตามมาตรฐานหรือข้อกำหนดทางเทคนิคของ กสทช.
Shure Incorporated Country Code Frequency Range Code de Pays Gamme de frequences Codice di paese Gamme di frequenza Código de país Gama de frequencias Länder-Kürzel Frequenzbereich HR, E, IRL, LV, RO, TR * All other countries * * This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Shure Incorporated L52 632-694 MHz Country Code Frequency Range Code de Pays Gamme de frequences Codice di paese Gamme di frequenza Código de país Gama de frequencias Länder-Kürzel Frequenzbereich A, B, BG, CH, CY, CZ, D, DK, EST, F * FIN, GB, GR, H, HR, I, IRL, IS, L, LT * M, N, NL, P, PL, RO, S, SK, SLO, TR * All other countries * * This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Shure Incorporated Q51 794-806 MHz Country Code Frequency Range Code de Pays Gamme de frequences Codice di paese Gamme di frequenza Código de país Gama de frequencias Länder-Kürzel Frequenzbereich A, B, BG, CH, CY, CZ, D, DK, E, EST * F, FIN, GB, GR, H, HR, I, IRL, IS, L, LT * LV, M, N, NL, P, PL, S, SK, SLO, TR * All other countries * * This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Shure Incorporated Certifications This device contains licenceexempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Develop ment Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Shure Incorporated QLXD4 Approved under the Declaration of Conformity (DoC) provision of FCC Part 15. Conforms to electrical safety requirements based on IEC 60065.
