Specifications

ManualsBrandsShure ManualsMicrophones and systemsS3

control is used; however, the appropriate attenua-

tion must be added to the Input Voltage (Horizontal)

Scale. For example, if the INPUT LEVEL control is

set to "5" aproximately 20 dB should be added to

the input voltage figures, so the point marked -60

dBV on the input voltage scale (Horizontal) would

become -40

dBV. In other words, the entire curve

would be shifted 20 dB to the right.

TO USE WlTH SHURE M68 SERIES MICROPHONE

MIXERS:

The two ways of using the M62V with the M68

Series Mixers are:

1. Connect a microphone directly to the microphone

input of the

M62V. Set INPUT IMPEDANCE

switch to appropriate position. Connect the mi-

crophone level output of the

M62V (Hi or Lo

Impedance) to a microphone input on the M68

mixer (either Hi or Lo Impedance, whichever

was selected on the

M62V). This method gives

audio "Level-Loc" control on the one micro-

phone attached to the

M62V

ONLY.

All other

inputs to the M68 are unaffected.

2. Connect the

M62V to control

ALL

inputs of the

M68 mixer, by connecting the microphone level

output of the M68 to the input of the

M62V, (if

the low-impedance microphone level output of

the M68 is used the

M62V input must be set to

"Lo Impedance," if the high-impedance micro-

phone level output of the M68 is used, the

M62V

input must be set to "Hi Impedance") or connect

the AUX.

HIGH LEVEL OUTPUT of the M68 to

the input (set for "Hi Impedance") of the

M62V.

(The INPUT LEVEL control may be used to con-

trol the threshold level as covered under "INPUT

LEVEL CONTROL.") The input for the main am-

plifier or tape recorder is then connected to the

M62V microphone level output (Hi or Lo Imped-

ance) or the AUX. OUTPUT. When used in this

manner, the MASTER CONTROL of the M68

Mixer should be set to about

"5"

and the indi-

vidual controls used to adjust the proper blend

between the channels. If more overall volume is

required,

the volume control on the main ampli-

fier should be advanced. This precaution will

prevent equipment overload.

TO USE WlTH SHURE M67 MICROPHONE MIXER:

Follow the instructions above for the M68, but only

the low-impedance input or output may be used when

connected to the M67. The setting of the M67 controls

only need be such that the VU meter indicates properly

to avoid overload.

TO USE WlTH SHURE M63 AUDIO MASTER:

Follow the instructions above but only the AUX.

OUTPUT of the

M62V may be used to feed the HI

LEVEL INPUT of the M63. The setting of the M63

VOLUME control will control the overall system gain

after the "Level-Loc".

OPERATION HINTS:

Remember that the M62V "Level-Loc" is a device

that provides a constant output level after a predeter-

mined input level (threshold) is reached, therefore,

more system gain is needed in PA applications or a

higher record level is desired in tape recording appli-

cations,

DO NOT INCREASE THE INPUT LEVEL GOING

INTO THE "LEVEL-LOC;"

once input threshold has

been reached the output level becomes fixed

IT CAN

NOT GO ANY HIGHER.

For more system gain, increase

the gain control of amplifier, preamplifier or tape re-

corder that is being fed from the

M62V.

Note:

For best results it is recommended that some

time be spent in experimentation with the

"Level-Loc" to enable the user to become ac-

customed to the advantages which this unit

presents.

Guarantee:

This Shure product is guaranteed in normal

use to be free from electrical and mechanical defects

for a period of one year from the date of purchase.

Please retain proof of purchase date. This guarantee

includes all parts and labor.

Shipping Instructions:

Carefully repack the unit and

return it prepaid to the factory. If outside the United

States, return the unit to your dealer or Authorized

Shure Service Center for repair. The unit will be re-

turned to you prepaid.

M62V Modification for

Non-disabling Aux. Output

The M62V may be rewired internally so that the AUX.

OUTPUT will operate (without "Level-Loc" action) when

the MASTER CONTROL is set to "Bypass", rather than

being disabled. This option is useful when the

M62V

AUX. OUTPUT is connected to the auxiliary input of the

M63 Audio Master or M68 Series Mixers. Note: With

this option, the

M62V power cannot be turned off by

the MASTER CONTROL switch. Power should be sup-

plied to the

M62V from an external source such as the

ACCESSORY 28 V. D.C. jack on the M68 Mixer or the

POS. (red) 30 V. D.C. jack on the M67 Mixer or M63

Audio Master, and the internal battery must be re-

moved.

To make this modification (see Figures 3 and

4):

Remove battery from unit.

2. Remove cover from unit.

3. Unsolder and remove wire between MASTER

CONTROL switch S3, terminal #8, and terminal

strip end of 10 kilohm,

watt resistor.

4. Unsolder wire from S3, terminal #7, and solder it

to terminal strip end of 10 kilohm,

watt resistor.

5. Unsolder positive end of 2 mfd x 15 volt capacitor

from collector of Q3.

6. Connect a wire from positive lead of 2

15 ca-

pacitor to S3, terminal

#8.

7. Connect a wire from collector of Q3 to S3, ter-

minal #7.

8. Connect a wire from center terminal of INPUT

LEVEL control

R1 to S3, terminal

#9.

Install a jumper wire between terminals

and

of S3.

10. Replace cover of unit, but do not install battery if

the

M62V is to be powered from an external

source.

MASTER

CONTROL

SWITCH

TERMINAL

DESIGNATIONS

(REAR

VIEW)