User's Manual

Antenna Combiners and Accessories
Antennas and receivers must be from the same band.
The supplied 1/4 wave antennas can be used when mounted directly to the UA844. If antennas
are remote mounted, 1/2 wave antennas must be used.
Antennas and cables are for use with UA844, and cannot be used with stand-alone SLX receivers
Passive Antenna/Splitter Combiner Kit
(recommended for 2 receivers)
UA221
25’ Antenna Cable UA825
50’ Antenna Cable UA850
100’Antenna Cable UA100
1/2 Wave Antenna Remote Mount Kit UA505
UHF Antenna Power Distribution Amplifier
(recommended for 3 or more receivers)
U.S.A. UA844US
Europe UA844E
UK UA844UK
1/2 wave antenna
H5 Band UA820H
J3 Band UA820F
L4 Band UA820L
P4, Q4 Bands UA820B
R13, R5, S6, JB Bands UA820A
12
Accessories and Parts
Optional Accessories
Carrying Case WA610
Black Grille for BETA 58A RK323G
Black Grille for BETA 87A and BETA 87C RK324G
Replacement Parts
Microphone Stand Adapter (SLX2) WA371
Zipper Bag (SLX1) 26A13
Zipper Bag (SLX2) 26A14
Short Rack Bar 53A8611
Long Rack Bar 53A8612
Link Bar 53B8443
Antenna extension cables (2) 95A9023
Protective Bumpers (SLX4 Receiver) (4) 90A8977
ACAdapter(120VAC,60Hz) PS21
ACAdapter(220VAC,50Hz) PS21AR
ACAdapter(230VAC,50/60Hz,Europlug) PS21E
ACAdapter(230VAC,50/60Hz) PS21UK
ACAdapter(100VAC,50/60Hz) PS21J
SM58
®
Cartridge with Grille (SLX2/SM58) RPW112
SM86 Cartridge with Grille (SLX2/SM86) RPW114
BETA 58A
®
Cartridge with Grille (SLX2/BETA 58) RPW118
BETA 87A Cartridge with Grille (SLX2/BETA 87A) RPW120
BETA 87C Cartridge with Grille (SLX2/BETA 87C™) RPW122
Matte Silver Grille for SM58
®
(SLX2/SM58) RK143G
Matte Silver Grille for SM86 (SLX2/SM86) RPM226
Matte Silver Grille for BETA 58A
®
(SLX2/BETA 58) RK265G
Matte Silver Grille for BETA 87A (SLX2/BETA 87A) RK312
Matte Silver Grille for BETA 87C (SLX2/BETA 87C™) RK312
Belt Clip 44A8030
1/4-Wave Antenna (470 - 752 MHz) UA400B
1/4-Wave Antenna (774 - 952 MHz) UA400
CERTIFICATION
SLX1, SLX2, SLX4
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Meets requirements of EMC standards EN 300 422 Parts 1 and 2 and EN 301 489 Parts 1 and 9.
Meets essential requirements of European R&TTE Directive 99/5/EC, eligible to bear the CE mark.
SLX1, SLX2
Certified under FCC Part 74. (FCC ID: DD4SLX1, DD4SLX2). Certified by IC in Canada under
RSS-123 and RSS-102. (IC: 616A-SLX1, 616A-SLX1G5, 616A-SLX2, 616A-SLX2G5).
SLX4
Approved under the Declaration of Conformity (DoC) provision of FCC Part 15. Certified in
Canada by IC to RSS-123. (IC: 616A-SLX4, 616A-SLX4G5).
Operation of this device is subject to the following two conditions: (1) this device may not cause in-
terference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European
representatives. For contact information please visit www.shure.com
The CE Declaration of Conformity can be obtained from: www shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str.12,
75031 Eppingen, Germany
Phone: +49-7262-92490
Fax: +49-7262-9249114
Email:EMEAsupport@shure.de
LICENSING INFORMATION
Licensing: A ministerial license to operate this equipment may be required in certain areas.
Consult your national authority for possible requirements. Changes or modifications not expressly
approved by Shure Incorporated could void your authority to operate the equipment. Licensing of
Shure wireless microphone equipment is the user’s responsibility, and licensability depends on the
user’s classification and application, and on the selected frequency. Shure strongly urges the user
to contact the appropriate telecommunications authority concerning proper licensing, and before
choosing and ordering frequencies.
Information to the user
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Note: EMC conformance testing is based on the use of supplied and recommended cable types.
The use of other cable types may degrade EMC performance.
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
WARNING: Dispose of properly. Check with local vendor for proper disposal of used battery and
electronics.