XPC Bios User Guide For the : DS61
Shuttle® XPC Installation Guide Copyright ©2012 by Shuttle® Inc. All Rights Reserved. No part of this publication may be reproduced, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means such as electronic, mechanical, magnetic, optical, chemical, photocopy, manual, or otherwise, without prior written permission from Shuttle® Inc.
Safety Information Read the following precautions before setting up a Shuttle XPC. CAUTION Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Disposal of used batteries according to the manufacturer's instructions. Installation Notices Do not place this device underneath heavy loads or in an unstable position. Do not expose this device to high levels of direct sunlight, highhumidity or wet conditions.
安全資訊 請在安裝Shuttle XPC前閱讀以下注意安全資訊。 警告 更換電池方式錯誤可能會損壞本電腦以及引發爆炸、火災或其他 危險。 僅能依Shuttle的建議，以相同或同等的電池更換。 請依照製造商的使用說明處理廢電池。 安裝聲明 切勿在此設備上放置重物 或將其置於不穩定的位置。 切勿讓此設備暴露於陽光 直接照射、濕度高、或潮 濕的環境中。 切勿在磁場附近使用此設備， 否則磁場干擾會影響設備的性能。 切勿阻塞此設備的通風口 或者以任何方式妨礙空氣流 動。
安全信息 请在安装Shuttle XPC前阅读以下注意安全信息。 注意 更换电池方式错误可能会损坏本电脑。 仅能依Shuttle的建议, 以相同或同等的电池更换。 请依照制造商的使用说明处理废电池。 安装声明 切勿在此设备上放置重物 或将其置于不稳定的位置。 切勿让此设备暴露于阳光 直接照射、湿度高、或潮 湿的环境中。 切勿在磁场附近使用此设备， 否则磁场干扰会影响设备的性能。 切勿阻塞此设备的通风口 或者以任何方式妨碍空气流 动。
TABLE OF CONTENTS Driver and Software Installation........................................................1 Motherboard Driver DVD............................................................1 User Manuals.............................................................................2 Appendix...........................................................................................3 Starting BIOS..............................................................................3 BIOS Setup Menu....................
English Driver and Software Installation Motherboard Driver DVD The DVD contents attached in DS61 Series motherboard are subject to change without notice. The Motherboard Driver DVD contains all the motherboard drivers necessary to optimize the performance of this Shuttle Xvision in a Windows® OS. Install these drivers after installing Microsoft® Windows®. Insert the attached DVD into your DVD-ROM drive. The DVD AutoRun screen should appear.
English User Manuals Motherboard Manual Quick Guide
English Appendix Starting BIOS AMIBIOS has been integrated into many motherboards for over a decade. In the past, people often referred to the AMIBIOS setup menu as BIOS, BIOS setup, or CMOS setup. American Megatrends refers to this setup as BIOS. Specifically, it is the name of the AMIBIOS8 BIOS setup utility. This chapter describes the basic navigation of the BIOS setup screens. Enter the BIOS To enter the BIOS setup screens, follow the steps below: Step1. Power on the motherboard. Step2.
English AMIBIOS8 has default text messages built into it. The motherboard manufacture retains the option to include, leave out, or change any of these text messages. They can also add their own text messages. Because of this, many screen shots in this manual are different from your BIOS setup screen. The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process.
English Main Setup When you first enter the BIOS Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below. System Time/System Date Use this option to change the system time and date. Highlight System Time or System Date using the keys. Enter new values through the keyboard.
English Advanced Select the Advanced tab from the BIOS setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the keys. All Advanced BIOS Setup options are described in this section. The Advanced BIOS Setup screen is shown below. The sub menus are described on the following pages.
English Power Management Configuration Suspend Mode Select the highest ACPI Sleep state the system will enter when the SUSPEND button is pressed. The choice: S1 (CPU Stop Clock) , S3(STR). Wake Up by USB (S3) Enable or disable system wake up by USB (S3). The choice: Enabled , Disabled. EuP Control Function Enable or disable system EuP function in S4/S5. The choice: Enabled , Disabled. PWR-On After PWR-Fail Enable or disable system power on automatically after AC power restored.
English Wake Up by Ring Enable or disable system wake up by Ring. The choice: Enabled , Disabled. Wake Up by LAN Enable or disable system wake on by onboard LAN chip. The choice: Enabled , Disabled. PowerOn by RTC Alarm When enabled, System will wake on the hr::min::sec specified. The choice: Enabled , Disabled. CPU Configuration You can use this screen to select options for the CPU Configuration Settings. Use the up and down keys to select an item.
English The CPU Configuration setup screen varies depending on the installed processor. Hyper-threading Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled. The choice: Enabled , Disabled. Active Processor Cores Number of cores to enable in each processor package. The choice: All,1,2,3.
English SATA Configuration SATA Mode Selection (1) IDE Mode. (2) AHCI Mode. Hot Plug Enable or disable Hot Plug capability. The choice: Enabled , Disabled.
English USB Configuration USB 3.0 Controller Set this value to allow the system to enable or disable the onboard USB 3.0 Controller. The choice: Enabled, Disabled.
English Hardware Health Configuration FAN1 Fan Speed Control function. The choice: Smart Fan Speed, Ultra-Low Mode, Low Mode, Mid Mode, Full Mode.
English OnBoard Device Configuration LVDS Panel Function This item allows you to enable or disable the LVDS function. The choice: Enabled , Disabled. Panel PWM Setting This item allows you to input PWM setting. The choice: 0~255. LVDS Channel Select This item allows you to switch type of LVDS data channel. The choice: Single, Dual. LVDS Bit Select This item allows you to switch type of LVDS data bit. The choice: 18bit, 24bit.
English High Definition Audio This item allows you to enable or disable the HD Audio. The choice: Enabled , Disabled. mSATA Function This item allows you to set the mSATA Function. The choice: Auto, Manual. Onboard LAN1 / LAN2 Function This item allows you to enable or disable the onboard LAN function. The choice: Enabled , Disabled. Onboard LAN Boot ROM This item allows you to enable or disable the onboard LAN boot ROM. The choice: Enabled , Disabled.
English Boot Select the Boot tab from the BIOS setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Boot Settings Configuration, to go to the sub menu for that item. You can display an Boot BIOS Setup option by highlighting it using the keys. All Boot BIOS Setup options are described in this section. The Boot BIOS Setup screen is shown below. The sub menus are described on the following pages.
English Security Select the Security tab from the BIOS setup screen to enter the Security BIOS Setup screen. You can display an Security BIOS Setup option by highlighting it using the keys. All Security BIOS Setup options are described in this section. The Security Setup screen is shown below. The sub menus are documented on the following pages. Flash Write Protection Enabled/Disabled BIOS Write Protection control function. The choice: Enabled , Disabled.
Select Change User Password to give or to abandon password setting same as Change Supervisor Password item above. Note that Supervisor Password field allows users to enter and change the settings of the BIOS SETUP UTILITY, while User Password field only allows users to enter the BIOS SETUP UTILITY without having the authorization to make any change. The Password Check item is used to specify the type of BIOS password protection that is implemented.
English Save & Exit Select the Exit tab from the BIOS setup screen to enter the Exit BIOS Setup screen. You can display an Exit BIOS Setup option by highlighting it using the keys. All Exit BIOS Setup options are described in this section. The Exit BIOS Setup screen is shown below. Save Changes and Exit When you have completed the system configuration changes, select this option to leave BIOS Setup and reboot the computer so the new system configuration parameters can take effect.
