® SIDEPOWER SE 60/185 S Ignition Protected thruster assembly is rd th a p bo ee n K al o u an m ! SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: +47 69 30 00 60 Fax: +47 69 30 00 70 w w w. s i d e - p o w e r. c o m s i d e p o w e r @ s l e i p n e r. n o Made in Norway Installation and user manual © Sleipner Motor AS version 1.
Contents Technical specifications ......................................................... 2 Technical specifications.............................................................. Planning && important importantprecautions.............................................. precautions ......................................... 3 Stern thruster thrusterinstallation installationconsiderations................................... considerations ............................. 3 Bolt on on installation installation.....
Planning and important precautions Prior to installation, it is important that the installer reads this guide to ensure necessary acquaintance with this product. The electromotor assembly must be handled carefully. Do not lift it by the internal connections or put it down on the driveshaft. Beware to keep installation within adviced measurements. We advice to paint the gearhouse and propellers with antifouling. PS! Do not paint the zinc anodes, sealings or propellershafts.
Fig. 1 SEALANT Fig. 2 WASHERS LOCKNUT OR DOUBLE NUTS SEALANT Bolt on installation of the stern tunnel 1. Make sure that there are enough space both inside and outside the transom of the boat. 6. Refer to the installation manual for the recommended thruster fitting. 2. Once the place for the installation has been decided, hold the tunnel in place in the horizontal position and mark the bolt holes. Remove the tunnel and it is then possible to calculate and mark the centre.
Fig. 1 Fig. 2 Grind off the bolt flange and the gelcoat both inside and outside in the areas shown. Boat transom Bond multiple layers both inside and outside Boat transom Stern tunnel Mould on installation of the stern tunnel 1. Make sure that there are enough space both inside and outside the transom of the boat. 2. Cut of the bolting flange on the stern-tunnel 3. Grind off the gelcoat both inside and outside the remaining “tube” atleast 10 cm down on the “tube” (Fig. 1). 4.
Fig. 1 Fig. 2 Bolt tightening forces: Bolts (2x) holding gearhouse to bracket: 17 Nm (12,4 lb/ft) 5 Fitting gearhouse and motor bracket lower-unit in in the the tunnel tunnel (remove (remove the thezinc zincanode) anode)first firstby byusing usingthe thegasket gasketinside insidethe thetunnel. tunnel.Try Tryon onthe thepropeller propellertotomake makesure sureit 1. Try the lower-unit it is centred the tunnel and turn freely with same clearance from each blade to the tunnel (Fig.
Fig. 1 5 4 3 2 1 Locktite Fitting propellers 1. Turn the propeller shaft so that the drivepin (5) is in a horizontal position and ensure that it is centred in the propellershaft. 2. Push the propeller onto the shaft with the track for the drivepin in an horizontal position (same direction as you set the drivepin), all the way in. There should be almost no gap between the propeller hub and the gearhouse. 3. Place the washer (4) on the prop.shaft and then tighten the lock-nut (3) on the propeller shaft.
Fig. 2 Fig. 1 Fitting the electromotor IP assembly 1. Remove the 4 bolts in the motorbracket (Fig 1). 2. Use the enclosed template to measure taht the driveshaft has come through the motorbracket with the correct hight (Fig 2). 3. Place the motor assembly gently on the motorbracket. Make sure that the drive pin in motor drive shaft fits the into the corresponding grove in the gearleg shaft. Be careful, the motor is heavy! 4.
Counter Nut Nut Washer Cable terminal Washer *C Counter Nut Nut *D Washer + Table for selection of main cable, Battery & cable recommendations: battery, fuse and main-switch up to 7m total Model SP55S2i IP Model sizes. SE60/185S Voltage Voltage 12 V 12 V 24 V 24 V +& - 8 - 11m total + & - Battery 12V or 24V 12 - 15m total + & - - 16 - 19m total + & - 20 - 23m total + & - 24 - 27m total + & - Nominal - 7-14m total + & - Min.Battery 15-21m total + &Cable - 22-28m total +Min.
Pin configuration in contacts 3 4 4 3 SIDEPOWER SIDEPOWER THRUSTER 1 2 THRUSTER 1 2 ON ON OFF ON SLEIPNER ON OFF SLEIPNER Control panel and control-leads • You can install as many many panels panels as as you youwish wishby byusing usingoptional optionalY-connectors. Y-connectors.
SESP55S2i 60/185Signition ignitionprotected protectedthruster thrusterassembly assembly Battery 12V or 24V Thermal switch A1 brown M 1.0- -2006 2007 1.
Technical wiring diagram 4 pin AMP connector On Motor blue (sig -) red red Fused 9 inside 1A 4 3 Electronic interface box 6 1232i white 7 red (+) 8 blue (sig +) 2 black (-) 6 grey (sig +) 1 grey (sig -) 5 4 2 1 3 A2 black M brown A1 Battery main switch Fuse Thermal switch Electrical installation of stern thruster systems y y y We advice to use different battery banks for each thruster to ensure maximum performance when both are used at the same time.
Checklist Propeller is fastened correctly to the shaft. Propeller turns freely in tunnel. The zinc-anode holding screw is tightened well with thread glue. There is a sturdy additional support under the electric motor, taking the weight load of the electromotor assembly away from the stern tunnel. All electrical wiring, cable sizes and battery capacity is according to the thruster installation manual. All bolts are securely tightened and sealant are applied as instructed.
Important user precautions Ensure that you know the location and how to operate the main battery switch and that disonnects the thruster from all power sources (batteries) so that the thruster can be turned off in case of a malfunction. Always turn the main power switch off before touching any part of the thruster, as an incidental start while touching moving parts can cause serious injuries. Always turn the control device off when the thruster is not in use.
To turn panel ON Turn boat to port To turn panel OFF Turn boat to starboard Bow+Stern Thruster How to use Sidepower thrusters How to use use aabowthruster bowthruster 1. Turn main power switch for the bowthruster bowthruster on. on. (Always (Always turn turn off off the the main main power power switch switch when when not not onboard.) onboard.) 2. Please take some time to exercise thruster usage usage in open water to avoid damages to your boat. 3.
1 2 3 4 Electromotor assembly Glassfibre reinforced lexan propeller for ultimate performance. Pre-filled lifetime lubricated gearhouse. Changeable zincanode protects gearhouse from corrosion in seawater. 1 3 2 4 5 4 3 1 2 3 4 5 Fastening screw for zincanode Zincanode Propeller lock nut Washer Drivepin for propeller 2 1 Locktite Maintenance » Keep the propeller and gearhouse clean from growth by painting with antifouling before every season.
Troubleshooting Before seeking assistance at the help desk of your Sidepower dealer / distributor please perform these tests and make notes of all measurements to ensure that they have as much information as possible to work on. NB! All check points and solutions must be carried out after consulting the relevant information elsewhere in this manual to understand how the system is intended to work. If you are unable to understand what to check, you must consult a professional.
Warranty statement 1. The equipment manufactured by Sleipner Motor AS (The “Warrantor”) is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4.
52 27 28 26 11 1 24 23 22 5 4 3 25 8 2 10 21 17 20 7 12 13 16 9 19 10 18 28. 27. 26. 25. 24. 23. 22. 21. 20. 19. 18. 17. 16. 15. 14. 13. 12. 11. 10. 9. 8. 7. 6. 5. 4. 3. 2. 1. SE 60/185S ignition protected thruster assembly 1.0 - 2007 SP 30 S2i / SP 40 S2 i/ SP 55 S2i 3.7 - 2006 07/06 < Part # Part # 12V 24V 09/07 < SE 60/185 S IP SP 55 S2i 1 Propeller 4 1261 w hen ordering brushes and brush springs.
Service Centres Argentina Trimer SA Buenos Aires Tel: +54 11 4580 0444 Fax: +54 11 4580 0440 www.trimer.com.ar trimer@trimer.com.ar Denmark Gertsen & Olufsen AS Hørsholm Tel: +45 4576 3600 Fax: +45 4576 1772 www.gertsen-olufsen.dk info@gertsen-olufsen.dk Australia AMI Sales Freemantle, WA Tel: +61 89 331 0000 Fax: +61 89 314 2929 ami@amisales.com.au Finland Nautikulma OY Turku Tel: +358 2 2503 444 Fax: +358 2 2518 470 www.nautikulma.fi nautikulma@nautikulma.fi Austria G.
