User's Manual
Table Of Contents
- Table of Contents
- SITRANS LR 460
- Specifications
- Installation
- Wiring
- 4-20 mA Start Up
- Local Operation
- LCD menu structure
- HART Communications
- Remote operation via PROFIBUS PA
- PROFIBUS PA Profile Structure
- Appendix A: Parameter Descriptions
- 1. Identification
- 2. Input
- 3. Output
- 5. Maintenance settings
- 6. Condensed Status Setup
- 6.1. Condensed Status Mode
- 6.1.1. Loss of Echo S0 (Status; Diagnosis)
- 6.1.2. Cable Fault S1 (Status; Diagnosis)
- 6.1.3. No Tech Power S2 (Status; Diagnosis)
- 6.1.4. Device Lifetime Maintenance Required Limit S3 (Status; Diagnosis)
- 6.1.5. Device Lifetime Maintenance Demanded Limit S4 (Status; Diagnosis)
- 6.1.8. Sensor Lifetime Maintenance Demanded Limit S7 (Status; Diagnosis)
- 6.1.9. Device Service Maintenance Required Limit S8 (Status; Diagnosis)
- 6.1.10. Device Service Maintenance Demanded Limit S9 (Status; Diagnosis)
- 6.1.11. LTB Scale S10 (Status; Diagnosis)
- 6.1.12. Internal Temp Sensor S11 (Status; Diagnosis)
- 6.1.13. Internal Temp High S12 (Status; Diagnosis)
- 6.1.16. AIFB2 PV Range S15 (Status; Diagnosis)
- 6.1.19. Calibration Schedule Maintenance Demanded Limit S18 (Status; Diagnosis)
- 6.1.30. Memory EEPROM S29 (Status; Diagnosis)
- 6.1.31. Memory EEPROM Flags S30 (Status; Diagnosis)
- 6.1.32. Memory Flash S31 (Status; Diagnosis)
- 6.1.33. Ident Violation S32 (Status; Diagnosis)
- 6.1.34. Internal Temperature Calibration S33 (Status; Diagnosis)
- 6.1. Condensed Status Mode
- Appendix B: Technical Reference
- Appendix C: Troubleshooting
- Appendix D: Maintenance
- Appendix E: Software Revision History
- Glossary
- Index
7ML19985JM01 SITRANS LR 460 – INSTRUCTION MANUAL Page 37
mmmmm
E: LCD menus
LCD menu structure
FOR PLACEMENT ONLY - TO BE REPLACED WITH FLIPOUT PAGE
1. Identification
1. Reset Filter
2. Standard Setup
3. Sensor Calibration’
4. Measuring Limits
5. Linearization
6. Detailed Setup
Input
Sensor Calibration
2. Configuration
3. Device
4. Statistics
1. Powered Hours
2. Powered Resets
Statistics
1. Temperature Unit
2. PV Unit
3. Sensor Units
Operation
1. Sensor Unit
2. Calibration Type
3. Low Calibration Pt.
4. High Calibration Pt.
5. Unit (Level)
6. Low Level Point
7. High Level Point
8. Level Offset
9. Sensor Offset
A. Temperature Unit
1. PV (volume/level) Unit
2. Linearization/Tank Shape
3. Linearization Volume
4. Dimension A
5. Dimension L
Linearization
1. Response Rate
2. Echo Lock
1. Address
2. Remote Lockout
3. Factory Reset
4. Reset Fault
5. Menu Timeout
Configuration
1. Software Revision
2. Loader Revision
3. Hardware Revision
4. PROFIBUS Ident Number
5. Lock
6. Language
Device
1. Min. Measurement Value
2. Max. measurement Value
3. Lower Value Min
4. Upper Value Max.
5. Process Temperature Min
6. Process Temperature Max
Measuring Limits
Standard Setup
See Output: page 39
Output
2. Input
3. Output
Identification