User's Guide
Table Of Contents
- RUGGEDCOM SAS-GW
- Table of Contents
- Preface
- 1. Introduction
- 2. Installation and Deployment
- 3. Using RUGGEDCOM SAS-GW
- 4. Configuring RUGGEDCOM SAS-GW
- 4.1. Configuring the Local Time Zone
- 4.2. Configuring the SNMP Read/Write Communities
- 4.3. Managing User Accounts
- 4.4. Managing Base Stations
- 4.4.1. Adding a Base Station
- 4.4.2. Updating a Base Station's Configuration
- 4.4.3. Updating a Base Station's Location
- 4.4.4. Updating a Base Station's Antenna Characteristics
- 4.4.5. Updating SNMP Settings
- 4.4.6. Updating CPI Information
- 4.4.7. Removing a Base Station
- 4.4.8. Viewing Available Base Stations
- 4.4.9. Viewing the Measurements Report
- 4.4.10. Viewing the SAS Registration Information
- 4.5. Managing Subscriber Units
- 5. Monitoring RUGGEDCOM SAS-GW
Chapter 4
Configuring RUGGEDCOM SAS-GW
RUGGEDCOM SAS-GW
User Guide
52 Updating a Base Station's Configuration
Parameter Description
Frequency Start Synopsis: A number between 3550000 and 37700000
The low value of the frequency bandwidth, measured in kilohertz (KHz), in which the
base station operates.
Frequency Stop Synopsis: A number between 3550000 and 37700000
The high value of the frequency bandwidth, measured in kilohertz (KHz), in which the
base station operates.
Serial Number Synopsis: A string
The serial number assigned to the base station by the vendor.
BST Max Tx Power Synopsis: A number between 17 and 27
The maximum transmission (Tx) power in dBm/10 MHz.
BST Max EIRP Synopsis: A number
The maximum EIRP, measured in decibels-per-minute/megahertz (dBm/MHz) permitted
by the grant.
SAS Control Synopsis: { Enabled, Disabled, Off the Grid }
Default: Enabled
Defines how RUGGEDCOM SAS-GW will handle the base station. Options include:
• Enabled – The base station will be reported to the SAS.
• Disabled – The base station will not be reported to the SAS. However, RUGGEDCOM
SAS-GW will still query the device for its status.
• Off the Grid – The base station will not be registered or queried. Any subscriber
units connected to the base station will also be unknown to RUGGEDCOM SAS-GW.
Report Measurements to SAS Synopsis: { No Reports, Report after Grant }
Default: Report after Grant
Controls whether the received power measurement is reported to the SAS. Options
include:
• No Reports – No reports are sent to the SAS
• Report after Grant – Power measurement is reported when spectrum has been
granted
CBSD Category Synopsis: { a, b }
Default: a
The CBSD category that applies to all devices behind the RUGGEDCOM SAS-GW. Options
include:
• a – Category A CBSDs are lower power devices that meet all general FCC requirements
and those set forth in sections 96.41 and 96.45 of the FCC's Code of Federal
Regulations (CFR)
• b – Category B CBSDs are higher power devices that meet all general FCC requirements
and those set forth in sections 96.41 and 96.45 of the FCC's Code of Federal
Regulations (CFR)
IMPORTANT!
When a is selected, information about the device installer is required. For
more information, refer to Section4.4.6, “Updating CPI Information” .
CBSD Group Synopsis: { Disabled, Enabled }
Default: Disabled
Controls whether grouping parameters are sent with registration requests. Options
include:
• Disabled – Registration requests are sent to the SAS without grouping parameters
• Enabled – Registration requests are sent to the SAS with grouping parameters