User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
Dect Configuration
A31003-C1010-S100-2-7620, 08/2010
120 HiPath Cordless IP, Service Manual
5.27.8.2 General configuration options
Server Ip
This field contains the IP address of the server (the IWU) in the DECT
network. It is used by the BSIP Only as the destination ip address for ip
packets.
Listen Port
This field defines the IP port on which the communication between the BSIP1
IWU and BSIP1 Only is established. The default value is 10500.
SystemAri
In this field the System ARI (DECT ID) which has to be unique at each DECT
system has to be configured. The SystemAri is provided by the system imple-
mentor. Supported System Ari’s are Class A and ClassB Ari.
SystemPIN
The "PIN" is a 8-digit number and it is needed for the registration of Handsets.
It is preconfigured with "00000000" and may be configured systemwide here.
IWU as GW
This option is only intended to access the BSIP1 Only when different VLANS
and/or VPNs are configured. It activates the routing functionality between the
VoIP (Infrastructure) network and the DECT network.
Hint: Using the BSIP1 IWU as a router influences the system (e.g. system
load for encryption) and may lead to to unpredictable system bahaviour.
Use this option only in case where other IP access is not available, e.g.
• SSH access to BSIP1 Only
• Access to WBM of BSIP1 Only
• Firmware update of BSIP1 Only
in case where other IP access is not available.
Therefore, you have to add add a route at the maintenance PC (Windows XP):
Example:
IP of BSIP1 IWU is 192.52.109.83, IP-DECT network is 192.168.201.0/
255.255.255.0