User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
"Status" Configuration
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 131
"+++"
"+++" in a line (Timeslot) shows that this is a Timeslot with a voice channel
(unidirectional) signal (The Timeslot number of the Rx channel is Tx Channel
+ 12).
One cell in a "Tx" line shows the value of the used Carrier for the voice
channel.
One cell in a "Rx" line shows the receive level of the Base Station in relation
to the active call.
"<value>"
Shows the current value (Receive resp. Send signal of the Rx resp. Tx
Timeslot) depending on the configuration of "RSSI", "Db" and "Limit".
Value ranges:
minimal value (corresponds to poor reception quality) -85 dB (resp. 30
[RSSI])
maximum value (corresponds to good reception quality) -50 dB (resp. 46
[RSSI])
Values outside a bbb, sss, or +++ line display the signal level (receive level)
of other DECT devices. The number of values as well as their value itself shall
be as small as possible.
The options at the lower part of the configuration page have the following
meanings:
"RSSI"
The values displayed in the RSSI table are RSSI values.
"Db"
The values displayed in the RSSI table are Db values.
"Limit"
Here you can configure a minimum value. Only values bigger (in the case of
"Db" only values smaller) than "Limit" are displayed in the RSSI table.
Normally the following default values are used:
RSSI:"30"
Db:"-85"
"Module Rssi"
Here you may select the Base Station which values are displayed at the table.