User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Open Source Software used in the Product Nur für den internen Gebrauch
A31003-C1010-S100-2-7620, 08/2010
178 HiPath Cordless IP, Service Manual
c08.fm
General Conditions
8 Open Source Software used in the Product
8.1 General Conditions
The Product "HiPath Cordless IP" contains, among other things, Open Source Software, li-
censed under an Open Source Software License and developed by third parties. These Open
Source Software files are protected by copyright. Your rights to use the Open Source Software
beyond the mere execution of Siemens´ program, is governed by the relevant Open Source
Software li-cense conditions.
Your compliance with those license conditions will entitle you to use the Open Source Software
as foreseen in the relevant license. In the event of conflicts between Siemens Enterprise Com-
munication GmbH&Co. KG license conditions and the Open Source Software license condi-
tions, the Open Source Software conditions shall prevail with respect to the Open Source Soft-
ware por-tions of the software. The Open Source Software is licensed royalty-free (i.e., no fees
are charged for exercising the licensed rights, whereas fees may be charged for reimbursement
of costs incurred by Siemens Enterprise Communication GmbH&Co. KG. The license condi-
tions can be found in the following chapters. In addition the license texts can be downloaded
from:
● The BSD License is available on the internet at:
http://www.freebsd.org/copyright/license.html
● The GPL v2 is available on the internet at:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
● The LGPL v2.1 is available on the internet at:
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
● The OpenSSL license is available on the internet at:
http://www.openssl.org/source/license.html
● The zLib license is available on the internet at:
http://www.zlib.net/zlib_license.html
If programs contained in this product are licensed under GNU General Public License (GPL)
and/or GNU Lesser General Public License (LGPL) and this software is not already delivered
in source code form together with the device, you can request the corresponding source code
from Siemens Enterprise Communication GmbH&Co. KG by paying a fee of 10 Euro for the
physical act of transferring the copy.
Please send your specific request, together with a receipt indicating the date of purchase, with-
in three years of your purchase, together with the MAC ID number of the device and the soft-
ware release number to: