User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Release notes
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 67
5.8 Release notes
Check the release notes of the belonging version of the firmware for restric-
tions and special considerations using the BSIP1.
5.9 Quick Start
The quick start chapter describes the initial operation of the HiPath Cordless
IP BSIP1 system for a first functional test including the necessary configu-
ration.
The "Quick Start" assumes the availabilty of
• two BSIP1, a
• functional PoE network switch, (alternatively a switch and Power
injectors ) and CAT.5 cables
• Maintenance PC (Windows XP based) with administration account and a
• supported PBX (e.g. HiPath OpenOffice ME).
Please read the corresponding chapter in the detailed manual parts if you
need further information regarding any step of the "Quick Start".
The following conditions apply:
• For the quick start it is assumed that no VLAN functionality is needed
• No special DECT functionality is configured (Antenna diversity,...).
5.10 Quick start overview
1. Prepare and connect hardware
2. Configure BSIP1 for IWU mode
3. Configuration of IP VoIP (Infrastructure) Network at BSIP IWU
4. Configuration of DECT Network at BSIP IWU
5. Configuration of users at the BSIP IWU
6. Configuration of users at the PBX
7. Start system services and register handsets at the BSIP IWU
8. Attach and configure further BSIP Only to the system