User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
"Network/Gateways" Configuration
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 99
1. A selected Gateway entry may be deleted by clicking [Delete Gateway].
The columns of the configuration page have the following meaning:
Enabled
When activating this element ( ) the selected Gateway (the PBX) is added to
the configuration and can be selected when configuring the Groups later on.
Name
Enter a unique name here for the Gateway. This name will be displayed in the
dropdown box of the available Gateways when configuring the Groups.
ListenPortRemote
This entry determines the common SIP listen port of the configured gateway.
There is no need to change this port to another value than 5060. The default
setting is "5060".
If adding new entries, the value is duplicated from the field
“Remote IpAddress”. If changing the value in Field “RemoteIPAddress”, the
value is only duplicated, if both values didn’t differ before. Otherwise the field
“GatekeeperId” remains unchanged.
Gatekeeper Id
The field “Gatekeeper Id“ is only displayed in SiemensAdmin mode . The
value is equal to the IP address of the VoIP Gateway. By default, enter the
same value as in field “Remote IP address“.
Remote IP Address
Enter the IP address of the Gateway (the PBX) here. It shall be located in the
IP Infrastructure network (see chapter 5.2, “Network Concept”). At the BSIP1
a corresponding IP Infrastructure address has to be configured.
Netmask
Enter the netmask for the IP address for the Gateway here. (Default for Class
C networks: 255.255.255.0).
Dtmf (only in advanced config. Mode)