User's Manual

ManualsBrandsSiemens Information and Communication Mobile ManualsElectronics242240

COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954

FCC ID: L82-242240

Page 98 of 129

Exhibit 8

Exhibit 8: User’s Manual

A copy of the user’s manual is enclosed below. The

compliance statement for the 242C is contained in a separate

document that is supplied with the phone, as shown below:

Important Safety Instructions and Product Information

BEFORE USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY INSTRUCTIONS

SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK AND INJURY TO PERSONS.

Read and understand all instructions.

Follow all warnings and instructions marked on the product.

Unplug this product from the wall telephone jack and power

outlet before cleaning. Do not use liquid cleaners or aerosol

cleaners. Use damp cloth for cleaning.

Do not use this product near water, for example, near a

bathtub, wash bowl, kitchen sink, or laundry tub, in a wet

basement or near a swimming pool.

Place this product securely on a stable surface. Serious

damage and/or injury may result if the unit falls.

Slots or openings in the cabinet and the back and bottom are

provided for ventilation, to protect it from overheating.

These openings must not be blocked or covered. This product

should never be placed near or over a radiator or heat

provided.

This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supply to your home, consult your dealer or

local power company.

Do not place objects on the power cord. Install the unit

where no one can step or trip on the cord.

Do not overload wall outlets and extension cords as this can

result in the risk of fire or electric shock.

10.

Never push objects of any kind into this product through

cabinet slots as they may touch dangerous voltage points or

short out parts that could result in the risk of fire or

electric shock. Never spill liquid of any kind on this

product.

11.

To reduce the risk of electric shock or burns, do not

disassemble this product. Take it to a qualified service

center when service is required. Opening or removing covers

may expose you to dangerous voltages, dangerous electrical

current or other risks. Incorrect reassembly can cause

electric shock when the appliance is subsequently used.

12.

Unplug the product from the wall outlet and refer servicing

to qualified service personnel under the following conditions:

When the power cord is damaged or frayed.

Summary of content (22 pages)

PAGE 1
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 98 of 129 Exhibit 8: User’s Manual A copy of the user’s manual is enclosed below. The compliance statement for the 242C is contained in a separate document that is supplied with the phone, as shown below: Important Safety Instructions and Product Information BEFORE USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY INSTRUCTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS. 1.
PAGE 2
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 99 of 129 b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions.
PAGE 3
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 100 of 129 placing used batteries into the trash or municipal waste stream, which is illegal in some areas. Please call 1-800-8BATTERY for information on battery recycling in your area. Siemens involvement in this program is part of our commitment to preserving our environment and conserving our natural resources.
PAGE 4
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 101 of 129 connect to your telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, the sum of the RENs of all devices connected to one line should not exceed five (5.0).
PAGE 5
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 102 of 129 3. Consult the dealer or an experienced radio TV technician for help. Notice to Hearing Aid Wearers: This phone system is compatible with inductively coupled hearing aids. Power Outage: In the event of a power outage, your cordless telephone will not operate. The cordless telephone requires electricity for operation.
PAGE 6
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 103 of 129 EXPRESS OR IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE ONE-YEAR DURATION OF THIS WRITTEN LIMITED WARRANTY.
PAGE 7
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 104 of 129 User’s Manual Model 242 Cordless Phone with Caller ID (a) WELCOME Congratulations on your purchase of the Siemens 242 cordless telephone. This phone has been designed with state of the art 2.4 GHz technology and will provide you with unsurpassed digital sound quality and security. Package Contents If an item listed below is not included in your package, please contact your local Siemens dealer.
PAGE 8
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 105 of 129 5. Plug the AC power adapter into the wall outlet (standard 110/120 VAC). If you do not have a standard wall plate, mount the base directly to the wall (mounting screws not included). Installation Tips Fully charge the battery pack 12 hours before first using the phone.
PAGE 9
COMMUNICATION CERTIFICATION LABORATORY • • TEST REPORT: 73-6954 FCC ID: L82-242240 Page 106 of 129 Place the handset in the base when not in use Clean the charging contacts on the handset and base once each month. To clean the charging contacts, use a pencil eraser or other contact cleaner. Do not use liquids or solvents they can damage your phone. RBRC Logo goes here Setting Basic Features Adjusting the Ring Volume and Turning the Ringer Off/On 1. Press MENU. 2.
PAGE 10
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 107 of 129 Selecting a Ring Tone 1. Press MENU. 2. Press the 6 key twice to move to “RING TONE?”. 4 RING TONE? DIAL MODE? 3. Press OK .to select “RING TONE?”(current tone will sound). RING TONE 2 4. Press 1 , 2 , 3 , or 4 to change the ring tone (selected tone will sound). 5. Press OK to save the ring tone setting. 6. Press MENU to exit.
PAGE 11
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 108 of 129 a local number readily available for call back or for moving it to a memory location. To store the local area code, 1. Press MENU. 2. Press the 6 key four times to move to “YOUR AREA CODE?” 4YOUR AREA CODE? CALL WAIT ID? 3. Press OK .to select “YOUR AREA CODE?”. ENTER AREA CODE _ _ _ 4. Enter the local area code. 5. Press OK to save the local area code. 6. Press MENU to exit.
PAGE 12
COMMUNICATION CERTIFICATION LABORATORY 5. Press 6. Press TEST REPORT: 73-6954 FCC ID: L82-242240 Page 109 of 129 OK to save the setting. MENU to exit. Selecting the Language to Display To select the language for screen display text, 1. Press MENU. 2. Press the 6 key six times to move to “LANGUAGE?”. 4LANGUAGE? MEMORY DIAL? 3. Press OK .to select “LANGUAGE?”. 4. Press the 5or 6 key to change the language. ENGLISH 5 6 TO CHANGE Or FRANCAIS 5 6 POUR CHANGER ESPANOL 5 6 PARA CAMBIAR Or 5. Press 6.
PAGE 13
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 110 of 129 Note: The display will show a maximum of 16 digits. If more than 16 are used, the digits at the left of the display move off the screen as additional digits are dialed. Note: The call timer will activate when you press TALK. Answering a Call 1. Remove the handset from the base OR 2. press TALK .. Ending a Call 1. Place the handset in the base OR 2. press TALK .
PAGE 14
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 111 of 129 ON”). 2. Press MUTE again to turn mute off. Answering Call Waiting If you subscribe to a call waiting (or 3-way calling) service from you local phone company, 1. Press FLASH to answer the second call (or to make a second call). 2. Press FLASH again to return to the first call (or to complete the 3-party call).
PAGE 15
COMMUNICATION CERTIFICATION LABORATORY 5. Press 6. Press OK to save the number. MENU to exit. 1. Press 2. Press TALK . MENU .t TEST REPORT: 73-6954 FCC ID: L82-242240 Page 112 of 129 Dialing a Memory Number PRESS MEMORY DIAL LOCATION 3. Press a memory location (0 to 9); the number is displayed and 1: 233-455-6777 0:00 dialed. Dialing Multiple Memory Numbers with Chain Dialing To dial more than one memory number (such as a bank account number or password), 1. Press TALK . 2. Press MENU .
PAGE 16
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 113 of 129 5. Press the second memory location (0 to 9); the number is displayed and entered. 2: 344-566-7888 0:10 6. Repeat steps 4 to 5 as needed to dial additional numbers. Deleting or Changing Memory Number 1. Press MENU. 4 MEMORY DIAL? RING VOLUME? PRESS MEMORY DIAL LOCATION 2. Press OK to select “MEMORY DIAL?”. 3. Press the memory location (0 to 9) you want to delete or change. 1: 233-455-6777 0:00 4.
PAGE 17
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 114 of 129 2. The handset beeps every seconds for 30 seconds and displays “paging from base” 3. Repeat as needed to locate the handset. 4. Press any button on the handset to end the Page. Page does not work if the handset is connected to a call or receiving a call. Caller ID Operation Receiving Caller ID 1. Caller ID name and number display when a call is received. JOHN DOE 222-555-1234 2.
PAGE 18
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 115 of 129 the display. Call Log Operation When the handset is idle, the display indicates the number of new calls in the Caller ID call log (if you subscribe to caller ID services). A maximum of 30 call log entries can be stored in the order they were received. When the call log is full, the oldest entry is removed and the newest entry is added. Viewing the Call Log 1.
PAGE 19
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 116 of 129 If the call you wish to dial requires a 1 before the dialing string (a long distance call) or a 0 (connecting through the operator) simply press the 1 or 0 before pressing TALK and the number will be automatically inserted at the beginning of the dialing string. Moving Call Log Entries to Memory Locations 1. Select the call log entry to move to a memory location (see “viewing the call log” steps 1-3). 2.
PAGE 20
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 117 of 129 log” steps 1-3). 2. Press DEL/MUTE to delete the call log entry. 3. The next call log entry received will display (or END, if no JOHN DOE 222-555-1234 12/01 11:30 AM entries remain). Delete All Call Log Entries 1. Select any call log entry. 2. Press MENU to open the call log menu. 4 MOVE TO MEMORY? DEL ALL CALLS? 3. Press the 6 key once to move to “DEL ALL CALLS?”. MOVE TO MEMORY? 4 DEL ALL CALLS? 4.
PAGE 21
COMMUNICATION CERTIFICATION LABORATORY • • TEST REPORT: 73-6954 FCC ID: L82-242240 Page 118 of 129 To stop the current operation and display Caller ID information, press MENU. To answer the call, press TALK. To stop the current operation and answer the call, press TALK. Caller ID information displays while connected to the call. Warnings Battery Low Warnings The battery pack needs to be recharged when the handset beeps 3 times every 30 seconds and displays “Battery Low”.
PAGE 22
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6954 FCC ID: L82-242240 Page 119 of 129 Problem The audio sounds weak or scratchy. Solution Move the handset or base to a different location. Avoid locating the handset or base near metal objects or appliances. Problem Unable to make or answer calls with the handset. Solution Make sure the AC adapter is plugged into the base, wall outlet, and telephone jack. Disconnect the AC adapter for a few minutes, and then reconnect it.