User Manual

ManualsBrandsSiemens ManualsOperator unitsWall-mounted sensors and room operator units for KNX PL-Link, KNS S-mode and KNX LTE-Mode - QMX3..

CM2N1602en_08

2020-04-03

Smart Infrastructure

602

QMX3.P37 QMX3.P34

P44

P74 QMX3.P02 QMX3.P70 QMX3.P30

/ P40

Desigo™ TRA

QMX3.P30

QMX3.P40

QMX3.P70

QMX3.P02

QMX3.P34

QMX3.P44

QMX3.P74

QMX3.P37

Wall-mounted sensors and room

operator units for KNX PL-Link,

KNX S-mode and KNX LTE-Mode

Communicative sensors, switches and room operator units with KNX (S-mode,

LTE-Mode) or KNX PL-Link (for Desigo™ Total Room Automation)

Functions (depending on type):

· Energy efficiency function ("Green Leaf ")

· Room temperature, CO

, and humidity measurement

· Control of light, blinds, and scenes

· PID controller for room temperature or ventilation (KNX S-mode)

· LCD Display for room temperature, operating mode, etc.

· Label for light, blinds and scenes (exchangeable, created with Word

template)

· Operation via 8 or 16 touchkeys

· Interface KNX (S-mode, LTE-Mode) and KNX PL-Link(for TRA, with plug &

play functionality)

· Powered over KNX PL-Link / KNX bus

· LEDs to indicate the switch state or the position of the device in dark rooms

Summary of content (16 pages)

PAGE 1
QMX3.P37 QMX3.P34 / P44 / P74 Desigo™ TRA Wall-mounted sensors and room operator units for KNX PL-Link, KNX S-mode and KNX LTE-Mode QMX3.P02 QMX3.P70 602 QMX3.P30 / P40 QMX3.P30 QMX3.P40 QMX3.P70 QMX3.P02 QMX3.P34 QMX3.P44 QMX3.P74 QMX3.
PAGE 2
X X QMX3.P70 QMX3.P70-1BSC S55624-H104 S55624-H125 X X Room operator units QMX3.P02 QMX3.P02-1BSC S55624-H107 S55624-H128 X QMX3.P34 QMX3.P34-1BSC QMX3.P44 QMX3.P44-1BSC QMX3.P74 QMX3.P74-1BSC S55624-H105 S55624-H126 S55624-H143 S55624-H144 S55624-H106 S55624-H127 X QMX3.P37 QMX3.P37-1BSC S55624-H108 S55624-H129 X Accessories QMX3.
PAGE 3
Use with KNX S-mode (continued) Switches Use with KNX LTE-Mode LTE can only use the sensor information of the types QMX3.P30, QMX3.P40, and QMX3.P70. NOTICE - switching and dimming of lights - control of blinds - selecting and saving of scenes Devices with CO2 measurement are not suitable for safety applications such as gas or smoke alarm. Mechanical design B C B2 B1 1602J01_01 A · The devices are designed for wall-mounting (A). A conduit box is optional.
PAGE 4
Engineering notes KNX PL-Link · The room operator units offer plug & play functionality. · The room operator units receive their power from the connected room automation station via the KNX PL-Link interface. · KNX PL-Link supports plug & play functionality for pre-configured devices out of the library · For KNX PL-Link wiring (topology, allowed cables and cable length), see the Desigo installation guide, CM111043. · Normally, electrical installers only install the base plate and the KNX PL-Link plug.
PAGE 5
2602J02 1602J108 Mounting over a conduit box *) Service LED (red) Tool plug Programming pin *) The installing tube must be sealed or cold or warm air may enter the device and cause faulty temperature readings by the internal sensor. Monting over a cavity wall box Use a metal-reinforced base plate QMX3.MP1 instead oft he standard base plate delivered with the room operator unit.
PAGE 6
Wall mounting Remove the breakout on the housing before putting the cable into the gaining channel. 4-wire cables (daisy chain wiring) Remove the cable coating, as it will not fit in the gaining channel. Cable ducts on the wall Keep a distance of 30 mm (from above) / 20 mm (from below) to the base plate, so that the device can be snapped onto the base plate. 30 mm Dismounting / service: 6 / 16 QMX3...
PAGE 7
Labels for QMX3.P02, QMX3.P37 Sample icons are available in the label template M1602.1 Information. e.g. on room operator unit location or on room type (free text) 1602J109 1602Z106 Insert label 1602J110 1602Z107 Remove label · For KNX PL-Link wiring (topology, allowed cables and cable length), see the Desigo TRA installation guide, CM111043. · Use the correct cables for the KNX PL-Link bus · Do not interchange the wires of the KNX PL-Link cable.
PAGE 8
Prerequisite for commissioning (KNX PL-Link) The room automation station must be running and an application must be loaded. Load application on the room automation station The application is not loaded on the room operator unit, but the room automation station. Download of the application is done using the SSA-DNT (Pack & Go) or the ABT. For this purpose (or for service), connect the ABT to the room automation station (USB or Ethernet).
PAGE 9
Manual commissioning (KNX PL-Link, without display) The devices are equipped with a programming pin and a red service LED on the back side (see page 4) Addressing 1. Short press the programming pin (<0.5 s). The device goes into programming mode; the service LED is continuously on. The tool identifies the current room operator unit that is operated and assigns it. 2. After the device is commissioned, deactivate the programming mode by shortly pressing the programming pin (<0.5 s). The service LED goes off.
PAGE 10
Commissioning (plug & play, KNX PL-Link) When only one device is connected to the KNX PL-Link bus, the room operator unit automatically establishes communications with the room automation station, from where the functions are downloaded to the room operator unit (plug & play). The following routine is executed: Step With display Description 1 The Build number and the version number of the device are displayed. 2 The Individual Address (IA) is downloaded to the device via KNX PL-Link.
PAGE 11
Commissioning (KNX) The devices are equipped with a programming pin and a red service LED for KNX commissioning (see page 4). Addressing 1. Short press the programming pin (<0.5 s). The device goes into programming mode; the service LED is continuously on. The tool identifies the current room operator unit that is operated and assigns it. 2. After the device is commissioned, deactivate the programming mode by shortly pressing the programming pin (<0.5 s). The service LED goes off.
PAGE 12
Display layout of room operator units · · · · · A B C D E A Display (temp., AQ, r.h.) B Setpoint adjustment (temperature) ****) C Operation (fan, operating mode) D Navigation E Presence / Comfort prolongation (display, operation) ****) Setpoint adjustment : ● Absolute value (23.5 °C) or relative value (+2 °C) Function of the display elements and keys Key Key 1 2 A B 5 6 3 7 4 8 · An arrow indicates that an element can be operated · Temperature display in °C or °F / humidity in % r.H.
PAGE 13
· Engineering functions (press keys 1 and 8 simultaneously during 5 s) – Programming mode (key 2), same function as programming pin – Connection test (Key 3) – Reset device to factory settings (key 4) Note: This operation is irreversible! · Indicates that the room operator unit is locked by the system. – Operation is disabled – The display in line 1 shows the temperature from bus Maintenance NOTICE The device can be cleaned with off-the shelf, solvent-free cleaning agents.
PAGE 14
Display Ports/interfaces Type Segment LCD Information displayed depends on the application in the room automation station. – – – – – – – Type of port between room automation station and room operator unit KNX / PL-Link Baud rate 9.6 kbps Standard KNX plug Wire diameter0.8 mm, max. 1.
PAGE 15
Connection R1 QMX3... room operator unit N1 Controller, actuator = KNX / PL-Link plug NOTICE + – Red Gray Twisted pair KNX PL-Link (positive) KNX PL-Link (negative) · Wires are NOT interchangeable. The device is protected against faulty wiring, but communications does not work on interchanged wires. · The KNX / KNX PL-Link bus MUST NOT be connected to the tool plug, only the tool. Tool plug (2.5 mm Jack) RJ45 plug of the tool cable 1 2 3 4 CE+, KNX CE-, KNX N.C. N.C. 5 6 7 8 Spannung 16 V N.C.
PAGE 16
Dimensions Issued by Siemens Switzerland Ltd Smart Infrastructure Global Headquarters Theilerstrasse 1a CH-6300 Zug Tel. +41 58 724 2424 www.siemens.com/buildingtechnologies © Siemens Switzerland Ltd, 2013 Technical specifications and availability subject to change without notice. 16 / 16 QMX3...