Installation Instructions

ManualsBrandsSiemens ManualsMetering devicesEcoView 8 DO Module Specification Sheet

Table Of Contents

EcoView™ 8 DO Module Installation and Commissioning

Document No. 129-565

April 28, 2015

EcoView™ 8 DO Module Installation and Commissioning

Item Number 129-565, Rev. CA Page 1 of 5

This document covers the installation and

commissioning of the EcoView™ 8 DO Module.

See the following documents for installation of other

EcoView system components:



EcoView Touchscreen Installation and System

Start-up

(129-562)



EcoView Thermostat Installation Instructions

(129-564 or 129-566)



EcoView Multi-phase Meter Installation

Instructions

(129-563)

Product Description

The EcoView 8 DO Module is an eight-channel, pilot-

duty controller module that is used to manage lighting

or other energy-consuming electrical loads that would

benefit from scheduling. Relay channels may be

accessed through the EcoView Touchscreen or

remotely through the EcoView Web application.

Product Number

57-002

EcoView I/O Module, 8 DO, with Zigbee,

includes power supply

Caution Notations

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow the procedures as

specified.

Required Tools and Materials

 Flat-blade screwdriver (1/8-inch blade width)

 Wire strippers

Expected Installation Time

 15 minutes for installing the EcoView 8 DO Module

 30 minutes for wiring each DO

Prerequisites

NOTE: If the EcoView 8 DO Module will be directly

controlling line voltage, it must be mounted in

an appropriate plastic NEMA enclosure.

 The EcoView Touchscreen is installed and started up

according to the

Installation Instructions

(129-562).

 A 120 Vac outlet is available for the EcoView 8

DO Module power supply.

Depending on the type of installation, other

prerequisites may have to be completed.

Installation

CAUTION:

Always wear an electro-static discharge

(ESD) wrist strap and discharge

accumulated static before touching field

panel components.

 Install the EcoView 8 DO Module near the loads

to be controlled.

1. If the EcoView 8 DO Module will be directly

controlling line voltage, mount the plastic NEMA

enclosure in the desired location.

2. If necessary, install a standard 120 Vac outlet in

the enclosure where the EcoView 8 DO Module

power supply will be attached.

3. Using the provided screws, mount the EcoView 8

DO Module assembly in the enclosure.

4. Attach the EcoView 8 DO Module 24 Vac power

supply to the standard 120 Vac outlet and secure

with the provided plate screw.

5. Wire the individual circuits to be controlled to the

2-pin connectors for Relay 1 – Relay 8.

NOTE: The relays are capable of controlling loads up

to 240 Vac at 3A. Anything outside of this

range should be controlled by contactors.

Summary of content (5 pages)

PAGE 1
Installation Instructions Document No. 129-565 April 28, 2015 EcoView™ 8 DO Module Installation and Commissioning This document covers the installation and commissioning of the EcoView™ 8 DO Module. See the following documents for installation of other EcoView system components:    EcoView Touchscreen Installation and System Start-up (129-562) Prerequisites NOTE: If the EcoView 8 DO Module will be directly controlling line voltage, it must be mounted in an appropriate plastic NEMA enclosure.
PAGE 2
Document No. 129-565 Installation Instructions April 28, 2015 Figure 1: EcoView™ 8 DO Module Reset Button Location. Figure 2: Device Settings/Configure Tab. Commissioning the 8 DO Module 5. Select the Resource Controller device driver from the list, and then press the Next button. In order to commission the EcoView 8 DO Module to the ZigBee network, the DO module needs to be reset. 1. Press the recessed Reset button four times in rapid succession (see Figure 1).  The NET light stops flashing.
PAGE 3
7. Select the appropriate Zigbee MAC Address for the 8 DO Module from the list, and then press the Finish button. 8. Press the Accept button. ⇨ The EcoView 8 DO Module is assigned to the EcoView Touchscreen and locked into the wireless network. 9. In the upper-left corner of the screen, press the Home button to return to the main screen. 10. Press the Exit button to save the configuration. The installation and commissioning are now complete. Figure 5: Device Wizard Zigbee MAC Selection.
PAGE 4
Document No. 129-565 Installation Instructions April 28, 2015 6. Press the Configure tab and deselect Hide Configured Devices. 7. In the list, select the EcoView 8 DO Module. 8. In the Device Configuration Wizard, press the Decommission button. 9. Press the Accept button. 10. Return to the EcoView 8 DO Module and install it on the correct EcoView Touchscreen network.
PAGE 5
Document No. 129-565 Installation Instructions April 28, 2015 FCC Code of Federal Regulations Title 47 Part 15.105 For Industry Canada User “This Class B digital apparatus complies with Canadian ICES-003 Issue 4 (February 2004).” Information to the user: This equipment has been tested and found to comply with the limits for a Class B, digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.