Programmiergerät Programming device LOGO! PROM Betriebsanleitung / Operating Instructions · 02/2010 SIPLUS extreme Answers for industry.
Deutsch SIPLUS extreme LOGO! PROM Betriebsanleitung 6AG1057-1AA01-0BA6 02/2010 A5E02562962A-02 1
Rechtliche Hinweise Warnhinweiskonzept Dieses Handbuch enthält Hinweise, die Sie zu Ihrer persönlichen Sicherheit sowie zur Vermeidung von Sachschäden beachten müssen. Die Hinweise zu Ihrer persönlichen Sicherheit sind durch ein Warndreieck hervorgehoben, Hinweise zu alleinigen Sachschäden stehen ohne Warndreieck. Je nach Gefährdungsstufe werden die Warnhinweise in abnehmender Reihenfolge wie folgt dargestellt.
1 Deutsch Beschreibung LOGO! PROM LOGO! PROM ist ein Programmiergerät für LOGO! Programmmodule und dient zum Vervielfältigen von Programmmodulen. Ein vorhandenes Mastermodul kann mit LOGO! PROM sehr einfach auf bis zu 8 Module kopiert werden. Nur Module, welche keinen Kopierschutz haben, können dupliziert werden. Eine Übertragung des Programms kann auch mittels eines LOGO! PC-Kabels und des PCProgramms LOGO! Soft Comfort V5.0/V6.0 in das LOGO! PROM vorgenommen werden.
Deutsch Funktionskontrolle Nach dem Einschalten wird ein zweimaliger Lampentest durchgeführt, d. h. alle LEDs leuchten kurz rot und grün auf. Eine Betriebskontrollleuchte ist nur vorhanden, wenn ein Modul oder das PC-Kabel im Modulschacht Master gesteckt ist. Die zugehörige LED leuchtet dann grün oder blinkt rot je nach Modultyp.
Deutsch Vorgehensweise für das Duplizieren mittels PC-Kabel Voraussetzung für einen Download mittels PC-Kabel ist LOGO! Soft Comfort V5.0/V6.0. Das PC-Kabel wird anstelle des Mastermoduls gesteckt und muss auch nach dem Download gesteckt bleiben. Bei nicht gestecktem Kabel kann kein Programmiervorgang gestartet werden. Der Download wird aus der LOGO! Soft Comfort, wie zu einem LOGO!-Gerät gestartet.
Deutsch Notwendiges/mögliches Zubehör LOGO! Soft Comfort V5.0 6ED1058-0BA01-0YA0 LOGO! Soft Comfort V6.0 6ED1058-0BA02-0YA0 LOGO! PC-Kabel 6ED1057-1AA00-0BA0 LOGO! Programmmodul, gelb 6ED1056-1BA00-0AA0 LOGO! Programmmodul, rot 6ED1056-4BA00-0AA0 LOGO! Memory Card 6ED1056-5CA00-0BA0 LOGO! Memory Card 6ED1056-1DA00-0BA0 LOGO! Memory/Battery Card 6ED1056-7DA00-0BA0 Evtl. Änderungen der Bestellnummern entnehmen Sie bitte dem Katalog ST70.
English SIPLUS extreme LOGO! PROM Operating Instructions 6AG1057-1AA01-0BA6 02/2010 A5E02562962A-02 1
Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.
1 English LOGO! PROM description LOGO! PROM is a programming device for LOGO! program modules which allows you to duplicate program modules. It is very easy to copy an existing master module to up to 8 modules using LOGO! PROM. Only modules that do not have copy protection can be duplicated. The program can also be transferred to the LOGO! PROM using a LOGO! PC cable and the LOGO! Soft Comfort V5.0/V6.0 PC program.
English Power-up The power for the LOGO! PROM is supplied by the plug-in power supply unit included with the product. CAUTION If you use a different power supply unit to the one included with the product, make sure that it complies with the safety regulations and bears a safety label. The output voltage of the plug-in power supply unit must not exceed or fall short of the input voltage range specified in the technical specifications. Function test After power-up, a double lamp test is performed, i.e.
English When all the modules have been removed, you can reset the LEDs by pressing the "Start/Reset" button. If new or already programmed modules are inserted, you can reset all the LEDs by pressing the "Start/Reset" button and the programming procedure is then started again. How to duplicate via a PC cable LOGO! Soft Comfort V5.0/V6.0 is the prerequisite for downloading via a PC cable. The PC cable is plugged in instead of the master cable and must also remain plugged in after the download.
English Required/possible accessories LOGO! Soft Comfort V5.0 6ED1058-0BA01-0YA0 LOGO! Soft Comfort V6.0 6ED1058-0BA02-0YA0 LOGO! PC cable 6ED1057-1AA00-0BA0 LOGO! Program module, yellow 6ED1056-1BA00-0AA0 LOGO! Program module, red 6ED1056-4BA00-0AA0 LOGO! Memory card 6ED1056-5CA00-0BA0 LOGO! Memory card 6ED1056-1DA00-0BA0 LOGO! Memory/battery card 6ED1056-7DA00-0BA0 See Catalog ST70 for any changes to the order numbers.
Weitere Informationen Get more Information www.siemens.de/siplus www.siemens.com/siplus www.siemens.de/logo www.siemens.com/logo Siemens AG Industry Sector I IA CE S IN - SIPLUS extreme Postfach 23 55 90713 Fürth GERMANY www.siemens.