Data Sheet

ManualsBrandsSIEMENS ManualsSiemens PLCsPLC electronics board 6AG1138-4FB04-2AB0

Data sheet 6AG1138-4FB04-2AB0

SIPLUS ET 200S F-DO 24 V PROFIsafe -25...+60°C with conformal

coating based on 6ES7138-4FB04-0AB0 . Electronics module for ET

200S, 4 F-DO PROFIsafe, 24 V DC/2 A, 30 mm overall width, up to

Category 4 (EN 954-1)/ SIL3 (IEC 61508)/PLE (ISO 13849), can also

be used in PROFINET configuration with IM 151-3 HF

Supply voltage

Load voltage L+

● Rated value (DC)

24V

● Reverse polarity protection

Input current

From load voltage L+ (no load), typ. 100mA

from backplane bus 3.3 V DC, max. 28mA

Power loss

Power loss, typ. 3.5W

Digital outputs

Type of digital output Transistor

Number of digital outputs 4

Short-circuit protection Yes

Limitation of inductive shutdown voltage to Typ. (2L+) -47 V

Controlling a digital input No

Switching capacity of the outputs

6AG1138-4FB04-2AB0 Subject to change without notice

Page 1/

Summary of content (4 pages)

PAGE 1
Data sheet 6AG1138-4FB04-2AB0 SIPLUS ET 200S F-DO 24 V PROFIsafe -25...+60°C with conformal coating based on 6ES7138-4FB04-0AB0 . Electronics module for ET 200S, 4 F-DO PROFIsafe, 24 V DC/2 A, 30 mm overall width, up to Category 4 (EN 954-1)/ SIL3 (IEC 61508)/PLE (ISO 13849), can also be used in PROFINET configuration with IM 151-3 HF Supply voltage Load voltage L+ ● Rated value (DC) 24 V ● Reverse polarity protection No Input current From load voltage L+ (no load), typ. 100 mA from backplane bus 3.
PAGE 2
● on lamp load, max. 10 W Load resistance range ● lower limit 12 Ω ● upper limit 1 kΩ Output voltage ● for signal "1", min. L+ (-2,0 V), current sourcing switch: L+ (-1,5 V), voltage drop on current sinking switch: max. 0.5 V Output current ● for signal "1" rated value 2A ● for signal "1" permissible range, min. 20 mA ● for signal "1" permissible range, max. 2.4 A ● for signal "0" residual current, max. 0.
PAGE 3
● between the channels No ● between the channels and backplane bus Yes ● Between the channels and load voltage L+ No Isolation tested with ● Load voltage L+ against backplane bus 2 545 V DC Standards, approvals, certificates Highest safety class achievable in safety mode ● acc. to EN 954 4 ● Performance level according to ISO 13849-1 PLe ● SIL acc. to IEC 61508 SIL 3 Ambient conditions Ambient temperature during operation ● min. -25 °C ● max. 60 °C ● At cold restart, min.
PAGE 4
— Environmental conditions for process, measuring and control systems acc. to ANSI/ISA-71.04 Yes; Level GX group A/B (excluding trichlorethylene; harmful gas concentrations up to the limits of EN 60721-3-3 class 3C4 permissible); level LC3 (salt spray) and level LB3 (oil) Remark — Note regarding classification of environmental conditions acc. to EN 60721, EN 60654-4 and ANSI/ISA-71.