Data Sheet

ManualsBrandsSIEMENS ManualsSiemens PLCs6AG1331-7NF10-2AB0 PLC input card

Data sheet 6AG1331-7NF10-2AB0

SIPLUS S7-300 SM 331 8AI 40-pole -25...+60°C with conformal

coating based on 6ES7331-7NF10-0AB0 . Analog "input isolated, ""8

AI; +/-5/10" V, 1-5 V, +/-20 mA, 0/4 to 20 mA, 16 bit, Single rooting

(60 V COM.), 4-channel operation: 10 ms, 8-channel operation: 23-

95ms, 1x 40-pole

Supply voltage

Load voltage L+

● Rated value (DC)

24V

● Reverse polarity protection

Yes

Input current

from load voltage L+ (without load), max. 200mA

from backplane bus 5 V DC, max. 100mA

Power loss

Power loss, typ. 3W

Analog inputs

Number of analog inputs 8

permissible input voltage for voltage input

(destruction limit), max.

75V; 35 V continuous, 75 V for max. 1 s (mark to space ratio

1:20)

permissible input current for current input (destruction

limit), max.

40mA

Input ranges

6AG1331-7NF10-2AB0 Subject to change without notice

Page 1/

Summary of content (5 pages)

PAGE 1
Data sheet 6AG1331-7NF10-2AB0 SIPLUS S7-300 SM 331 8AI 40-pole -25...+60°C with conformal coating based on 6ES7331-7NF10-0AB0 . Analog "input isolated, ""8 AI; +/-5/10" V, 1-5 V, +/-20 mA, 0/4 to 20 mA, 16 bit, Single rooting (60 V COM.), 4-channel operation: 10 ms, 8-channel operation: 2395ms, 1x 40-pole Supply voltage Load voltage L+ ● Rated value (DC) 24 V ● Reverse polarity protection Yes Input current from load voltage L+ (without load), max. 200 mA from backplane bus 5 V DC, max.
PAGE 2
● Voltage Yes ● Current Yes ● Thermocouple No ● Resistance thermometer No ● Resistance No Input ranges (rated values), voltages ● 0 to +10 V No ● 1 V to 5 V Yes ● Input resistance (1 V to 5 V) 10 MΩ ● 1 V to 10 V No ● -1 V to +1 V No ● -10 V to +10 V Yes ● Input resistance (-10 V to +10 V) 10 MΩ ● -2.5 V to +2.
PAGE 3
Input ranges (rated values), resistance thermometer ● Cu 10 No ● Ni 100 No ● Ni 1000 No ● LG-Ni 1000 No ● Ni 120 No ● Ni 200 No ● Ni 500 No ● Pt 100 No ● Pt 1000 No ● Pt 200 No ● Pt 500 No Input ranges (rated values), resistors ● 0 to 150 ohms No ● 0 to 300 ohms No ● 0 to 600 ohms No ● 0 to 6000 ohms No Cable length ● shielded, max.
PAGE 4
Diagnostics function Yes; Parameterizable Alarms ● Diagnostic alarm Yes; Parameterizable ● Limit value alarm Yes; Parameterizable all channels (end of cycle interrupt is also supported across modules) ● Hardware interrupt Yes; Parameterizable, channels 0 to 7 (on exceeding limit value), at end of cycle Diagnostic messages ● Diagnostic information readable Yes Diagnostics indication LED ● Group error SF (red) Yes Potential separation Potential separation analog inputs ● between the channels and b
PAGE 5
Use in stationary industrial systems — to biologically active substances according to EN 60721-3-3 Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request — to chemically active substances according to EN 60721-3-3 Yes; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-252 (severity degree 3); * — to mechanically active substances according to EN 60721-3-3 Yes; Class 3S4 incl.