Data Sheet

ManualsBrandsSIEMENS ManualsSiemens PLCs6AG1531-7PF00-4AB0 PLC add-on module

Data sheet 6AG1531-7PF00-4AB0

SIPLUS S7-1500 AI 8XU/R/RTD/TC HF 0 ... +60°C with conformal

coating based on 6ES7531-7PF00-0AB0 . Analog Input Module AI 8

X U/R/RTD/TC HF, 16 BITS OF RESOLUTION, Accuracy 0.1%, 8

Channels in "groups of 1; common mode" Voltage: 30 V AC/60 V DC,

"Diagnosis, Process alarms;" incl. infeed element, Shield clamp and

Shield terminal

General information

Product type designation AI 8xU/R/RTD/TC HF

Firmware version

● FW update possible

Yes

Product function

● I&M data

Yes; I&M0 to I&M3

● Measuring range scalable

Yes

● Scalable measured values

● Adjustment of measuring range

Engineering with

● PROFIBUS as of GSD version/GSD revision

V1.0 / V5.1

● PROFINET as of GSD version/GSD revision

V2.3 / -

Operating mode

● Oversampling

● MSI

Yes

CiR – Configuration in RUN

Reparameterization possible in RUN Yes

6AG1531-7PF00-4AB0 Subject to change without notice

Page 1/

Summary of content (9 pages)

PAGE 1
Data sheet 6AG1531-7PF00-4AB0 SIPLUS S7-1500 AI 8XU/R/RTD/TC HF 0 ... +60°C with conformal coating based on 6ES7531-7PF00-0AB0 . Analog Input Module AI 8 X U/R/RTD/TC HF, 16 BITS OF RESOLUTION, Accuracy 0.1%, 8 Channels in "groups of 1; common mode" Voltage: 30 V AC/60 V DC, "Diagnosis, Process alarms;" incl.
PAGE 2
Calibration possible in RUN Yes Supply voltage Type of supply voltage DC Rated value (DC) 24 V permissible range, lower limit (DC) 20.4 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes Input current Current consumption, max. 55 mA; with 24 V DC supply Power Power available from the backplane bus 0.85 W Power loss Power loss, typ. 1.
PAGE 3
● Input resistance (-80 mV to +80 mV) 10 MΩ Input ranges (rated values), currents ● 0 to 20 mA No ● -20 mA to +20 mA No ● 4 mA to 20 mA No Input ranges (rated values), thermocouples ● Type B Yes ● Input resistance (Type B) 10 MΩ ● Type C Yes ● Input resistance (Type C) 10 MΩ ● Type E Yes ● Input resistance (Type E) 10 MΩ ● Type J Yes ● Input resistance (type J) 10 MΩ ● Type K Yes ● Input resistance (Type K) 10 MΩ ● Type L No ● Type N Yes ● Input resistance (Type N) 10 MΩ ●
PAGE 4
● Input resistance (Ni 10) 10 MΩ ● Ni 10 according to GOST Yes; Standard/climate ● Input resistance (Ni 10 according to GOST) 10 MΩ ● Ni 100 Yes; Standard/climate ● Input resistance (Ni 100) 10 MΩ ● Ni 100 according to GOST Yes; Standard/climate ● Input resistance (Ni 100 according to GOST) 10 MΩ ● Ni 1000 Yes; Standard/climate ● Input resistance (Ni 1000) 10 MΩ ● Ni 1000 according to GOST Yes; Standard/climate ● Input resistance (Ni 1000 according to GOST) 10 MΩ ● LG-Ni 1000 Yes; Sta
PAGE 5
● Pt 200 Yes; Standard/climate ● Input resistance (Pt 200) 10 MΩ ● Pt 200 according to GOST Yes; Standard/climate ● Input resistance (Pt 200 according to GOST) 10 MΩ ● Pt 500 Yes; Standard/climate ● Input resistance (Pt 500) 10 MΩ ● Pt 500 according to GOST Yes; Standard/climate ● Input resistance (Pt 500 according to GOST) 10 MΩ Input ranges (rated values), resistors ● 0 to 150 ohms Yes ● Input resistance (0 to 150 ohms) 10 MΩ ● 0 to 300 ohms Yes ● Input resistance (0 to 300 ohms) 10
PAGE 6
— additional conversion time for wire-break monitoring Thermocouples, 150 Ohm, 300 Ohm, 600 Ohm, Cu10, Cu50, Cu100, Ni10, Ni50, Ni100, Ni120, Ni200, Pt10, Pt50, Pt100, Pt200: 4 ms; 6 kOhm, Ni500, Ni1000, LG-Ni1000, Pt500, Pt1000: 13 ms ● Interference voltage suppression for interference frequency f1 in Hz 400 / 60 / 50 / 10 Hz ● Basic execution time of the module (all channels released) Corresponds to the channel with the highest basic conversion time Smoothing of measured values ● parameterizable Ye
PAGE 7
● Resistance, relative to input range, (+/-) 0.05 % ● Resistance thermometer, relative to input range, (+/-) Cuxxx Standard: ±0.3 K, Cuxxx Klima: ±0.2 K, Ptxxx Standard: ±0.5 K, Ptxxx Klima: ±0.2 K, Nixxx Standard: ±0.3 K, Nixxx Klima: ±0.15 K ● Thermocouple, relative to input range, (+/-) Type B: > 600 °C ±1 K, Type E: > -200 °C ±0.5 K, Type J: > -210 °C ±0.5 K, Type K: > -200 °C ±1 K, Type N: > -200 °C ±1 K, Type R: > 0 °C ±1 K, Type S: > 0 °C ±1 K, Type T: > -200 °C ±0.
PAGE 8
Isolation tested with 2 000 V DC between the channels and the supply voltage L+; 2 000 V DC between the channels and the backplane bus; 2 000 V DC between the channels; 707 V DC (type test) between the supply voltage L+ and the backplane bus Ambient conditions Ambient temperature during operation ● horizontal installation, min. 0 °C; = Tmin (incl. condensation/frost) ● horizontal installation, max. 60 °C; = Tmax ● vertical installation, min. 0 °C; = Tmin ● vertical installation, max.
PAGE 9
— Note regarding classification of environmental conditions acc. to EN 60721, EN 60654-4 and ANSI/ISA-71.04 * The supplied plug covers must remain in place over the unused interfaces during operation! Conformal coating ● Coatings for printed circuit board assemblies acc. to EN 61086 Yes; Class 2 for high availability ● Protection against fouling acc.