Datasheet

ManualsBrandsSiemens ManualsPressure SensorsPressure Transmitter 0-10 bar G1/2

Pressure Measurement

Transmitters for basic requirements

SITRANS P200

for gauge and absolute pressure

2/5

Siemens FI 01 · 2012

■

Overview

The SITRANS P200 pressure transmitter measures the gauge

and absolute pressure of liquids, gases and vapors.

• Ceramic measuring cell

• Gauge and absolute measuring ranges 1 to 60 bar (15 to

1000 psi)

• For general applications

■

Benefits

• High measuring accuracy

• Rugged stainless steel enclosure

• High overload withstand capability

• For aggressive and non-aggressive media

• For measuring the pressure of liquids, gases and vapors

• Compact design

■

Application

The SITRANS P200 pressure transmitter for gauge and absolute

pressure is used in the following industrial areas:

• Mechanical engineering

• Shipbuilding

• Power engineering

• Chemical industry

• Water supply

■

Design

Device structure without explosion protection

The pressure transmitter consists of a piezoresistive measuring

cell with a diaphragm installed in a stainless steel enclosure. It

can be used with a connector per EN 175301-803-A (IP65), a

round plug M12 (IP67), a cable (IP67) or a cable quick screw

connection (IP67) connected electrically. The output signal is

between 4 and 20 mA or 0 and 10 V.

Device structure with explosion protection

The pressure transmitter consists of a piezoresistive measuring

cell with a diaphragm installed in a stainless steel enclosure. It

can be used with a connector per EN 175301-803-A (IP65) or a

round plug M12 (IP67) connected electrically. The output signal

is between 4 and 20 mA.

■

Function

The pressure transmitter measures the gauge and absolute

pressure of liquids and gases as well as the level of liquids.

Mode of operation

SITRANS P200 pressure transmitters (7MF1565-...), functional diagram

The ceramic measuring cell has a thin-film resistance bridge to

which the operating pressure p is transmitted through a ceramic

diaphragm.

The voltage output from the measuring cell is converted by an

amplifier into an output current of 4 to 20 mA or an output voltage

of 0 to 10 V DC.

The output current and voltage are linearly proportional to the in-

put pressure.

const.

, U

FI01_2012_en_kap02.book Seite 5 Donnerstag, 17. November 2011 4:31 16

Summary of content (17 pages)

PAGE 1
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P200 for gauge and absolute pressure ■ Overview ■ Design Device structure without explosion protection The pressure transmitter consists of a piezoresistive measuring cell with a diaphragm installed in a stainless steel enclosure. It can be used with a connector per EN 175301-803-A (IP65), a round plug M12 (IP67), a cable (IP67) or a cable quick screw connection (IP67) connected electrically.
PAGE 2
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P200 for gauge and absolute pressure ■ Technical specifications Application Design Gauge and absolute pressure measurement 2 Liquids, gases and vapors Mode of operation Measuring principle Piezo-resistive measuring cell (ceramic diaphragm) Measured variable Gauge and absolute pressure Weight Approx. 0.090 kg (0.
PAGE 3
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P200 for gauge and absolute pressure ■ Selection and ordering data Order No. SITRANS P 200 pressure transmitters for pressure and absolute pressure for general applications Characteristic curve deviation typ. 0.25 % Wetted parts materials: Ceramic and stainless steel + sealing material Non-wetted parts materials: stainless steel Measuring range Overload limit Min.
PAGE 4
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P200 for gauge and absolute pressure ■ Selection and ordering data 2 SITRANS P 200 pressure transmitters for pressure and absolute pressure for general applications Accuracy typ. 0.25 % Wetted parts materials: Ceramic and stainless steel + sealing material Non-wetted parts materials: stainless steel Order No. Order code D) 7M F 1 5 6 5 - 7 7 7 7 7 - 7 7 7 7 7 7 7 Output signal 4 ...
PAGE 5
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P200 for gauge and absolute pressure ■ Dimensional drawings 25.5 (1.0) G1/2" 2 25 (1.0) 25 (1.0) 20 (0.8) G1/8" M16x1.5 or 1/2-14 NPT 20 (0.8) M12x1/Fixcon 51 (2.0) 10.7 (0.42) 36 (1.42) M20 x 1.5 G1/2" 1/2-14 NPT 20 (0.8) 16 (0.6) G1/4" 7/16"-20 UNF 1/4-18 NPT max. 20 Nm 7/16"-20 UNF max. 20 Nm 23 (0.9) SITRANS P200, electrical connections, dimensions in mm (inch) 25 (1.
PAGE 6
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P200 for gauge and absolute pressure ■ Schematics 1+ 1 2 2 IO Connection: 1 (+), 2 (-) + 2- UB RL IO UB RL 3- IO gn UB RL 1 IO 2- UB RL 1+ 4 3 1 2 UO + UB RL 4+ 3- Connection: 1 (+UB), 3 (-), 4 (+UO) UO Output voltage RL Load UB Power supply Connection with voltage output and connector M12x1 br UO gn + UB RL ws Connection: br (+UB, brown), gn (+UO, green), ws (-, white) UO Output voltage UB
PAGE 7
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P210 for gauge pressure ■ Overview ■ Design Device structure without explosion protection The pressure transmitter consists of a piezoresistive measuring cell with a diaphragm installed in a stainless steel enclosure. It can be used with a connector per EN 175301-803-A (IP65), a round plug M12 (IP67), a cable (IP67) or a cable quick screw connection (IP67) connected electrically.
PAGE 8
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P210 for gauge pressure ■ Technical specifications Application Design Gauge measurement 2 Liquids, gases and vapors Mode of operation Measuring principle Piezoresistive measuring cell (stainless steel diaphragm) Measured variable Gauge pressure Weight Approx. 0.090 kg (0.198 lb) Process connections See dimension drawings Electrical connections • Connector per EN 175301-803-A Form A with cable inlet M16x1.
PAGE 9
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P210 for gauge pressure ■ Selection and ordering data Order No. Measuring range Overload limit min. Order code D) 7M F 1 5 6 6 - 7 7 7 7 7 - 7 7 7 7 7 7 7 SITRANS P 210 pressure transmitters for gauge pressure for low pressure applications Accuracy typ. 0.25 % Wetted parts materials: Stainless steel + sealing material Non-wetted parts materials: stainless steel 2 Burst pressure max. For gauge pressure 0 ...
PAGE 10
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P210 for gauge pressure ■ Dimensional drawings 25.5 (1.0) G1/2" 25 (1.0) 25 (1.0) 20 (0.8) G1/8" M16x1.5 or 1/2-14 NPT 20 (0.8) M12x1/Fixcon M20 x 1.5 G1/2" 1/2-14 NPT 24 (0.94) SITRANS P210, electrical connections, dimensions in mm (inch) 20 (0.8) Cable gland with cable 16 (0.6) 30.2 (1.19) max. 30 Nm 16 (0.6) 2 51 (2.0) 10.7 (0.42) 36 (1.42) G1/4" 7/16"-20 UNF 1/4-18 NPT 25 (1.0) max.
PAGE 11
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P210 for gauge pressure ■ Schematics 1+ 1 2 IO Connection: 1 (+), 2 (-) + 2- UB RL IO UB RL 3- IO gn UB RL 1 IO 2- UB RL 1+ 4 3 1 2 UO + UB RL 4+ 3- 2 Connection: 1 (+UB), 3 (-), 4 (+UO) UO Output voltage RL Load UB Power supply Connection with voltage output and connector M12x1 br UO gn + UB RL ws Connection: br (+UB, brown), gn (+UO, green), ws (-, white) UO Output voltage UB Power supply
PAGE 12
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P220 for gauge pressure ■ Overview ■ Design Device structure without explosion protection The pressure transmitter consists of a piezoresistive measuring cell with a diaphragm installed in a stainless steel enclosure. It can be used with a connector per EN 175301-803-A (IP65), a round plug M12 (IP67), a cable (IP67) or a cable quick screw connection (IP67) connected electrically.
PAGE 13
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P220 for gauge pressure ■ Technical specifications Application Gauge pressure measurement Design Liquids, gases and vapors Mode of operation Measuring principle Piezoresistive measuring cell (stainless steel diaphragm) Measured variable Gauge pressure Weight Approx. 0.090 kg (0.198 lb) Process connections See dimension drawings Electrical connections • Connector per EN 175301-803-A Form A with cable inlet M16x1.
PAGE 14
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P220 for gauge pressure ■ Selection and ordering data 2 Order No. SITRANS P 220 pressure transmitters for gauge pressure, high-pressure and refrigeration applications, fully-welded version Accuracy typ. 0.25 % Wetted parts materials: stainless steel Non-wetted parts materials: stainless steel Measuring range Overload limit Minimum Order code D) 7M F 1 5 6 7 - 7 7 7 7 7 - 7 7 A 07 7 7 7 Burst pressure Max.
PAGE 15
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P220 for gauge pressure ■ Selection and ordering data SITRANS P 220 pressure transmitters for gauge pressure, high-pressure and refrigeration applications, fully-welded version Accuracy typ. 0.25 % Wetted parts materials: stainless steel Non-wetted parts materials: stainless steel Order No.
PAGE 16
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P220 for gauge pressure ■ Dimensional drawings 25.5 (1.0) G1/2" 25 (1.0) 25 (1.0) 20 (0.8) G1/8" M16x1.5 or 1/2-14 NPT 20 (0.8) M12x1/Fixcon M20 x 1.5 G1/2" 1/2-14 NPT 24 (0.94) SITRANS P220, electrical connections, dimensions in mm (inch) 20 (0.8) Cable gland with cable 16 (0.6) 30.2 (1.19) max. 30 Nm 16 (0.6) 2 51 (2.0) 10.7 (0.42) 36 (1.42) G1/4" 7/16"-20 UNF 1/4-18 NPT 25 (1.0) max.
PAGE 17
© Siemens AG 2011 Pressure Measurement Transmitters for basic requirements SITRANS P220 for gauge pressure ■ Schematics 1+ 1 2 IO Connection: 1 (+), 2 (-) + 2- UB RL IO UB RL 3- IO gn UB RL 1 IO 2- UB RL 1+ 4 3 1 2 UO + UB RL 4+ 3- 2 Connection: 1 (+UB), 3 (-), 4 (+UO) UO Output voltage RL Load UB Power supply Connection with voltage output and connector M12x1 br UO gn + UB RL ws Connection: br (+UB, brown), gn (+UO, green), ws (-, white) UO Output voltage UB Power supply