POWERS® Pneumatic Controls Thermostats Controllers and Transmitters Mechanical Line Voltage Controls Relays and Three-way Valve Damper Actuators Control Cabinets Scan code to download this mini catalog A6V11476665 6/19/2019
Pneumatic Thermostats Powerstar® Single Setpoint Pneumatic Thermostat 192 S The 192 S Thermostats are proportional single output, single setpoint, 1-pipe (low air capacity) or 2-pipe (high air capacity) sensor controllers. Each thermostat includes a wall mounting plate for installation in a variety of rough-in terminal boxes. A sensitive bimetal responds to temperature change to modulate control air through a flapper nozzle. One setpoint dial is provided. Air connections are made with 5/32” (4 mm) O.D.
RETROLINE® Powerstar® Retrostat Pneumatic Room Thermostats “192-194 Retrostats” The Powerstar™ RETROLINE™ Retrostat Pneumatic Room Thermostat converts most existing pneumatic room thermostats to a Powerstar 192/194 direct or reverse acting, 2-pipe, single or dual setpoint unit. Day/Night or Heat/Cool Retrostat is factory calibrated to match the appropriate changeover pressure of the competitive thermostat.
Pneumatic Controllers and Transmitters Powers® Controls 195 Single Input Receiver-Controller The RC 195 Single Input Receiver-Controller is a pneumatic instrument which receives one pneumatic input, either direct acting (DA) or reverse acting (RA). It produces a pneumatic control signal based on the net pneumatic input and the mechanical settings of the setpoint and percent proportional band.
Pneumatic Controllers and Transmitters Accessories Powers® Controls 195 Single Input Receiver-Controller Accessories Click the link below for Powers Controls™ 195 Single Input Receiver-Controller Accessories. Technical Instructions Powers® Controls 195 Multiple Input Receiver-Controller Accessories Click the link below for Powers Controls™ 195 Multiple Input Receiver Controller Accessories.
Powers® Mechanical Line Voltage Controls Powers® Electric Line Voltage Mechanical Room Thermostats The ET 134 line voltage room thermostat is a wall mounted instrument available with exposed or concealed set point adjustment. Models are available with Single-Pole, Single-Throw (SPST) or Single-Pole, Double-Throw (SPDT) contact action and for standard-duty (nominal ¼ hp; 10 amps, non-inductive) applications.
Powers® Line Voltage Pressure-Electric Switches The SW 134 Pressure Electric Switch actuates electrical circuits from pneumatic control signals. The 134 Pressure Electric Switches are heavy duty pressure-actuated, mechanical contact type switches used to open or close electrical circuits from pressure signals in pneumatic control systems.
Powers® Mechanical Line Voltage Controls Accessories Static Pressure Sensor Probe Click the link below for Powers™ Mechanical Line Voltage Thermostat Accessories. Technical Instructions Coil Clip Click the link below for Powers™ Mechanical Line Voltage Thermostat Accessories. Technical Instructions Capillary Clip Click the link below for Powers™ Mechanical Line Voltage Thermostat Accessories.
Powers® 243 Series Pneumatic Relays and Three-way Valve Powers® 243 MP Multi-Purpose Relay The Powers RL 243 MP Multi-Purpose Relay is a pneumatic auxiliary device designed to provide a variety of pneumatic control functions for the typical control system. Applications include direct and reverse acting amplifying, signal advancing, minimum pressure relay, and lower pressure transfer.
Powers™ Controls Pneumatic Damper Actuators Powers® Controls No. 3 Pneumatic Damper Actuators The Powers® Controls No. 3 Pneumatic Damper Actuator is a compact, totally enclosed, rolling diaphragm-type actuator designed for modulating or two-position actuation of dampers or air valves. This actuator has a stroke length of 2-3/8 inches (60mm) and is available in nominal spring ranges of 3 to 7 psi (21 to 50 kPa), 5 to 10 psi (35 to 69 kPa) and 8 to 13 psi (55 to 90 kPa).
Powers® Controls Pneumatic Damper Actuators Accessories No. 3 Pneumatic Damper Actuators Accessories Click the link below for No. 3 Pneumatic Damper Actuator Accessories. Technical Instructions No. 4 Pneumatic Damper Actuators Accessories Click the link below for No. 4 Pneumatic Damper Actuator Accessories. Technical Instructions No. 6 Pneumatic Damper Actuators Accessories Click the link below for No. 6 Pneumatic Damper Actuator Accessories.
Powers® Controls CP 567 Control Cabinets 567 Series Control Cabinet Assemblies 3.5-inch Depth These cabinets provide a convenient central location for equipment such as power metering, small electronic controls and accessories. These 12” H × 14” W × 3.5” D cabinets provide a smaller profile for the mounting and protection of small electronic controls or power metering devices.
567 Series Control Cabinet Components Perforated Mounting Sub-Panels Only The perforated mounting sub panels are designed to fit the 567 series control cabinet enclosures. They can also be used as a convenient mounting plate in other cabinets or wall mounted device applications.
Quick Reference Guides Available Powers® Pneumatic Thermostats This quick reference guide is a four page family product focus document with more information on Pneumatic Thermostats and related links. Quick Reference Guide Powers® Damper Actuators This quick reference guide is a four page family product focus document with more information on Damper Actuators and related links.
Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. Powers is a registered trademark of Siemens Industry, Inc. Other product or company names mentioned herein may be the trademarks of their respective owners. © 2019 Siemens Industry, Inc. Siemens Industry, Inc. Your feedback is important to us. If you have Document No.
