User Manual

ManualsBrandsSiemens ManualsExtinguishing - Cylinder Valve ActuatorsACTF230-EL BM C

A6V11387469_en--_a Smart Infrastructure

2020

Building Products

Sinorix™

ACTF230-EL BM C

CO2

Solenoid actuator with built

in blocking device and monitoring contacts for F230

cylinder valve

● Compatibility with F230 valves

● Mounting on the EL actuation port

● Built-in blocking device with monitoring contacts

● Connecting cable with LED for solenoid actuator

● Cable for monitoring contacts

Product code: S54476-B525-A3

Summary of content (8 pages)

PAGE 1
Sinorix™ ACTF230-EL BM C CO2 Solenoid actuator with built-in blocking device and monitoring contacts for F230 cylinder valve ● Compatibility with F230 valves ● Mounting on the EL actuation port ● Built-in blocking device with monitoring contacts ● Connecting cable with LED for solenoid actuator ● Cable for monitoring contacts Product code: S54476-B525-A3 A6V11387469_en--_a 2020-09-02 Smart Infrastructure Building Products
PAGE 2
Use This product must only be used with SinorixTM fixed automatic extinguishing systems. Functions An actuator is a valve opening device used to release the gas contained in the cylinder. The solenoid actuator is fitted to the cylinder valve EL actuation port. It gets electrically activated by the ECP. The solenoid actuator is polarity-independent. The cable connector for the solenoid actuator can be installed with the cable running upwards or downwards.
PAGE 3
Equipment combinations Compatible valves Reference Description Product code F230-CO2-190 Cylinder valve F2301001 S54476-B500-A11 F230-CO2-250 Cylinder valve F2301000 S54476-B500-A1 Authorized actuator combinations It is not permitted to use any actuator on the PM actuation port while an actuator with built-in blocking device is used on the EL actuation port.
PAGE 4
Mounting Pre-mounting: ● Check that the safety cap is fitted on the cylinder valve outlet. ● Check that the plug is fitted on the branch for connecting the pilot hose. ● Remove the cap of the EL actuation port. ● Screw the actuator onto the EL valve actuation port by hand. ● Tighten using a 24 mm wrench. Torque: 20 Nm ±2 Nm ● Connect the discharge hose, and pilot hose if necessary. WARNING System actuation hazard Do not electrically connect the actuator.
PAGE 5
After an actuation ● Unscrew the actuator from the cylinder valve. ● Replace the cylinder. ● Move the cap of the EL valve actuation port from the full to the empty cylinder. ● Fit the actuator to the EL valve actuation port, on the full cylinder. ● Connect the cable. Only use actuators in good condition.
PAGE 6
Technical data Technical data Actuation voltage 24 VDC ±15 % polarity-independent Nominal actuation current 0.42 A (at 24 VDC 20 °C) Maximum monitoring current 5 mA Minimum actuation time 10 s Duty cycle 100 % Connector DIN EN 175301-803 shape C (8 mm), male Connecting cable DIN EN 175301-803 shape C (8 mm), female, with LED Bare cable ends 5m 3 x 0.
PAGE 7
Dimensions Dimensions in mm Connecting cable of cylinder valve connector BK-1: black-1 BK-2: black-2 GN/YE: green/yellow Connecting cable of monitoring contacts WH: BN: GN: YE: GY: PK: BU: RD: (M) white brown green yellow grey pink blue red "Actuator mounted" monitoring contact M-U (white) Contact is closed when the actuator is not mounted on the cylinder valve M-I (brown) Contact is closed when the actuator is mounted on the cylinder valve M-C (green) Common (A) Activated A-1 (yellow) A-2 (grey)
PAGE 8
Issued by Siemens Switzerland Ltd Smart Infrastructure Global Headquarters Theilerstrasse 1a CH-6300 Zug Tel. +41 58 724 2424 www.siemens.com/buildingtechnologies 8 Siemens Schweiz AG Building Products Document ID A6V11387469_en--_a Edition 2020-09-02 © Siemens Switzerland Ltd, 2019 Technical specifications and availability subject to change without notice.