SiPass integrated AFI5100 Installation manual Fire Safety & Security Products Siemens Building Technologies
Liefermöglichkeiten und technische Änderungen vorbehalten. Data and design subject to change without notice. / Supply subject to availability. © 2008 Copyright by Siemens Building Technologies Wir behalten uns alle Rechte an diesem Dokument und an dem in ihm dargestellten Gegenstand vor.
Contents 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 Input Point Module (AFI5100) ................................................................5 Product Description...................................................................................5 Product Numbers ......................................................................................5 Prerequisites .............................................................................................5 Expected Installation Time.....................
Siemens Building Technologies Fire Safety & Security Products 11.
Input Point Module (AFI5100) 1 Input Point Module (AFI5100) 1.1 Product Description The AFI5100 is an Input Point Module used as part of a Siemens integrated access control and security solution. It provides an interface between an Advanced Access Controller (ACC) and up to 32 input devices used to monitor a secure facility. The AFI5100 continuously monitors the status of all input devices connected; for example, Passive Infrared Detectors (PIRs).
Input Point Module (AFI5100) 1.5 Mounting Instructions 1. Remove the AFI5100 from its carton and discard the packaging material. 2. Place the AFI5100 (base-plate) against the surface to which it is to be affixed and mark the location of the mounting holes. 3. If being mounted within a cabinet, simply align the AFI5100 base-plate with the holes located on the cabinet backplane and proceed to step 3. 4. It is recommended that you affix the AFI5100 in all four of the mounting locations. WARNING 1.
Input Point Module (AFI5100) 7. Connect the active (+ve) and neutral (-ve) wires from the Power Supply Unit (PSU) to the POWER IN port. Ensure the polarity of the connection is made correctly. 8. Check all connections thoroughly. 9. Power can now be applied to the AFI5100 .The following diagram displays the layout and dimensions of the AFI5100 with brace attached: 287mm (11.30") 9mm (0.35") (0.35") 9mm 257mm (10.12") 5mm (0.
Input Point Module (AFI5100) The following diagram displays the location of the ports on the AFI5100 : 1 3 2 IN+ ININ- IN+ FOR IN IN+ INPUT 1 IN- IN+ INPUT 5 IN- INPUT 6 IN- IN+ INPUT2 IN- IN+ FOR NORMAL LK1 LK2 IN+ IN+ INPUT 4 IN- INPUT 7 IN- IN+ INPUT 3 IN+ IN- INPUT 9 IN- IN+ IN- IN- IN+ IN- IN+ INPUT 13 INPUT 8 IN+ INPUT 10 IN+ INPUT 11 IN+ IN- IN- INPUT 15 INPUT 14 IN- IN+ INPUT 12 IN+ IN- IN+ INPUT 17 IN- IN+ IN- INPUT 21 INPUT 16 IN+ IN- IN
Input Point Module (AFI5100) 1.7 Links and Jumpers The following table outlines the link settings for the AFI5100: Value LK1, LK2 Links 1 and 2 are used to configure whether Fire Over-ride (FOR) will operate in Enhanced FOR mode or Normal. To enable Normal Mode: If the links are set to the off position, FOR input will have no effect on the state of the output relays.
Input Point Module (AFI5100) 1.8 LEDs The following table describes the operation of the LEDs located on the AFI5100 : LED Brief Description POWER The POWER led is illuminated when power has been applied to the device. ACTIVITY The ACTIVITY led indicates that the AFI5100 is accessing information contained in its internal database or performing a routine operation. This LED also indicates whether the initial instruction set has been downloaded.
Input Point Module (AFI5100) 1.
Issued by Siemens Building Technologies Fire & Security Products GmbH & Co. oHG D-76181 Karlsruhe www.sbt.siemens.com Document no. A24205-A335-B245 Edition 11.2007 © 2008 Copyright by Siemens Building Technologies Data and design subject to change without notice. Supply subject to availability. Printed in the Federal Republic of Germany on environment-friendly chlorine-free paper.
