Installation Instructions

ManualsBrandsSiemens ManualsBuilding automationAPOGEE Wiring Guidelines for Field Panels and Equipment Controllers

Document No. 545-406

January 23, 2004

AO-P Module and Connector Block

Item Number: 545-406-05, Rev. 011 Page 1 of 4

Product Description

The Analog Output Pneumatic (AO-P) module

provides a single pneumatic control point for the

Modular Building Controller (MBC) and Remote

Building Controller (RBC).

The AO-P Point Termination Module (PTM) consists

of a separate electronic point module and a mating

connector block (Figure 1).

Product Numbers

PTM6.1PSI20-M One Analog Output—Pneumatic

with Manual Override

545-021 Replacement PTM6.1PSI20-M

AOP Point Module Only

545-020 Replacement PTM6.1PSI20-M

AOP Connector Block Only

Accessories

545-825 APOGEE Address Keys, 1-16

545-826 APOGEE Address Keys, 17-32

545-827 APOGEE Address Keys, 33-48

545-828 APOGEE Address Keys, 49-64

545-829 APOGEE Address Keys, 65-80

545-040 pre-APOGEE Address Keys, 004-064

545-041 pre-APOGEE Address Keys, 068-128

545-042 pre-APOGEE Address Keys, 132-192

545-043 pre-APOGEE Address Keys, 196-256

545-044 pre-APOGEE Address Keys, 260-296

545-053 Identification Labels (12 per sheet)

Caution Notation

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow the procedures as

specified.

Required Tools

• Cutters for pneumatic tubing

• Tie-wraps

Expected Installation Time

10 minutes per module

Prerequisites

• MBC or RBC mounted and AC power

connected.

• Pneumatic tubing installed.

• Identification labels and job layout sheet

printed.

NOTE: Module identification labels and layout

sheets are generated in the field office by

the Field Workstation and are typically

supplied for each MBC/RBC enclosure.

Figure 1. AO-P Point Module and Connector Block.

Summary of content (4 pages)

PAGE 1
Installation Instructions Document No. 545-406 January 23, 2004 AO-P Module and Connector Block Caution Notation Product Description The Analog Output Pneumatic (AO-P) module provides a single pneumatic control point for the Modular Building Controller (MBC) and Remote Building Controller (RBC). The AO-P Point Termination Module (PTM) consists of a separate electronic point module and a mating connector block (Figure 1). Product Numbers PTM6.
PAGE 2
Document No. 545-406 Installation Instructions January 23, 2004 Installation Inserting Address Keys and Address Markers NOTE: All PTMs have a piece of color-coded tape affixed to the right side of the identification window to identify the module type. AO-P modules have pink tape. An address key is inserted into each AO-P point module to provide a unique address to both the Open Processor and the point database. Inserting the Module Labels Do the following for each AO-P module being installed: 1.
PAGE 3
Document No. 545-406 Installation Instructions January 23, 2004 Installing the Connector Block Do the following for each connector block being installed: 1. Use the MBC/RBC layout sheet to determine the correct block position number. The block position number is printed on the mounting rail label as 1A, 2A, etc. (Figure 4). 2. Remove the protective tape along the perforations to uncover the slot where the connector block attaches to the Module BUS (M-BUS). 3.
PAGE 4
Document No. 545-406 Installation Instructions January 23, 2004 Repositioning or Removing an AO-P Module Installing the AO-P Module Do the following for each AO-P module being installed: 1. 2. Use the MBC layout sheet and address keys and markers to match the AO-P module to the appropriate connector block. Remove any M-BUS protective tape that was not removed when the connector block was installed. 3. Align the AO-P module mounting guides with the right edge of the M-BUS rail (Figure 7). 4.