Installation Instructions

ManualsBrandsSiemens ManualsBuilding automationAPOGEE Wiring Guidelines for Field Panels and Equipment Controllers

Document No. 553-671

February 10, 2011

PXM10T/S and HOA

Remote Door Mount Kit

Page 1 of 4

Product Description

The PXM10T/S and HOA Remote Door Mount Kit is

available as an accessory for use with the PXM10T,

PXM10S, or HOA for PXC Compact (PXA8-M,

PXA16-M, and PXA16-MR). The kit allows the

PXM10T/S or HOA to be mounted on the inside or

the outside of the field panel enclosure door.

Each kit includes the following components:

 Mounting kit base with industrial adhesive

strip

 Controller opening cover

 Two 1/8” mounting screws

 Four wire ties

Product Numbers

PXA-HMI.RMKIT PXM10T/S and HOA Remote

Door Mount Kit

Accessories

PXA-HMI.CABLEP5 Cable required to establish

power and communication

connection with Siemens

Compact 16 and 24 point

controllers

Not Included Ethernet CAT 5, CAT 5E, or

CAT 6 cable (max. CAT 5

cable length is 2 meters)

Warning/Caution Notations

WARNING:

Personal injury or property

damage may occur if you do not

follow procedures as specified.

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow procedures as specified.

Required Tools

 5/8” to 3/4” drill bit or knockout punch tool

 Flathead screwdriver

Expected Installation Time

10 minutes.

Compliance

CAUTION:

For use with Siemens Field Panel

enclosures. Any other use voids all UL,

CSA, and FCC approvals, as well as

European EMC and LVD compliance.

Installation

Use the following installation procedure when

installing the PXM10T/S and HOA Remote Door

Mount Kit.

1. Remove the existing cover from the controller:

U14 U15U8 U9 U10 U11 U12 U13 AO2 AO3AO1U1624V 24V

PXC0089R1

Summary of content (4 pages)

PAGE 1
Installation Instructions Document No. 553-671 February 10, 2011 PXM10T/S and HOA Remote Door Mount Kit Product Description The PXM10T/S and HOA Remote Door Mount Kit is available as an accessory for use with the PXM10T, PXM10S, or HOA for PXC Compact (PXA8-M, PXA16-M, and PXA16-MR). The kit allows the PXM10T/S or HOA to be mounted on the inside or the outside of the field panel enclosure door. CAUTION: For use with Siemens Field Panel enclosures.
PAGE 2
Document No. 553-671 Installation Instructions February 1, 2011 5. Insert the lower two cover tabs into the slots located at the bottom of the controller opening: U8 24V 2. Attach one end of the Ethernet cable to the connector underneath the circuit board inside the controller opening cover. Secure the cable inside the cover, using the cable restraints and the notch on the side of the cover: 24V U9 U12 PXM0012R1 U10 U11 U13 U14 U15 U16 AO1 3.
PAGE 3
Document No. 553-671 Installation Instructions February 1, 2011 Installing the Mounting Kit Base onto the Field Panel Door (Inside or Outside) 5. Affix the base to a flat section toward the middle of the enclosure door using one of the following methods: 1. Print and cut out the template image below. Use the template to determine the appropriate location for the mounting kit base. a.
PAGE 4
Document No. 553-671 Installation Instructions February 1, 2011 CAUTION: This template must be printed at original size for accurate placement. 5/8” to 3/4” Hole For CableRouting If Installed Outside Enclosure 1/8” Holes For Mounting Screws PXM0021R1 Adhesive Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced.