Operating Instructions

Index
Index-4 Siemens Building Technologies, Inc.
in Application 2524....................................3-56
in Application 2526....................................3-70
DI OVRD SW (Point 19) ..........................1-3, 4-2
digital input................................................See DI
digital output............................................ See DO
DMPR COMD (Point 48)
definition......................................................4-4
in Application 2500......................................3-6
in Application 2501....................................3-17
in Application 2520......................................2-6
in Application 2521....................................2-15
in Application 2522....................................3-30
in Application 2523....................................3-45
in Application 2524....................................3-58
in Application 2526....................................3-72
DMPR POS (Point 49)
definition......................................................4-5
in Application 2500......................................3-7
in Application 2501....................................3-18
in Application 2522....................................3-33
DMPR ROT ANG (Point 56) ...........................4-5
DMPR STATUS (Point 84)
definition......................................................4-7
in Application 2500......................................3-7
in Application 2501....................................3-18
in Application 2522....................................3-33
DO (digital output)
general information..............................1-4, G-2
in Application 2500....................... 3-3, 3-4, 3-9
in Application 2501................. 3-13, 3-14, 3-20
in Application 2520....................... 2-3, 2-4, 2-8
in Application 2521................. 2-12, 2-13, 2-17
in Application 2522................. 3-24, 3-27, 3-35
in Application 2523................. 3-40, 3-42, 3-48
in Application 2524................. 3-53, 3-55, 3-62
in Application 2526................. 3-67, 3-69, 3-76
DO 1 (Point 41)...............................................4-4
DO 2 (Point 42)...............................................4-4
DO 3 (Point 43)......................................3-81, 4-4
DO 4 (Point 44)......................................3-81, 4-4
DO DIR.REV (Point 59) ..................................4-5
DUCT AREA (Point 97) ..................................4-8
duty cycle
in Application 2522....................................3-31
in Application 2524....................................3-58
in Application 2526....................................3-73
E
EHEAT FLOW (Point 60).......................3-32, 4-5
electric heat interlock ....................................3-32
English units..........G-2. See also point database
equipment controller ...................................... G-3
ERROR STATUS (Point 99)..................4-8, 5-25
F
failure codes) .................................................. 5-6
fan
in Application 2524............ 3-53, 3-60, 4-3, 4-4
in Application 2526............ 3-67, 3-74, 4-3, 4-4
FAN (Point 44)
definition......................................................4-4
in Application 2524....................................3-60
in Application 2526....................................3-74
field panel
and ATEC slave mode.....................2-21, 3-81
general information ...............1-2, 2-2, 3-2, G-3
in Application 2500......................................3-6
in Application 2501...........................3-16, 3-17
in Application 2520......................................2-5
in Application 2521...........................2-14, 2-15
in Application 2522....................................3-28
in Application 2523....................................3-43
in Application 2524....................................3-56
in Application 2526....................................3-70
FLN................................................................ G-3
FLN LED indicator ...................................1-5, 5-4
FLN trunk connections check ....................... 5-22
flow
actual....................................................4-4, 4-6
loop ...................................... See control loops
maximum.......................................4-3, 4-4, 4-6
minimum
general information....................4-3, 4-4, 4-6
in Application 2522.........................3-31, 4-5
in Application 2523................................ 3-45
in Application 2526................................ 3-73
oscillating ....................................................3-8
setpoint
active .......................................................4-8
in Application 2501.................................. 3-6
in Application 2501................................ 3-17
in Application 2520.................................. 2-6
in Application 2521................................ 2-15
in Application 2522................................ 3-30
in Application 2523................................ 3-45
in Application 2524................................ 3-58
in Application 2526................................ 3-72
FLOW (Point 75)............................................. 4-6
FLOW BIAS (Point 74) ...................................4-6
FLOW COEFF (Point 36) ...............................4-4
FLOW D GAIN (Point 73) ............................... 4-6
FLOW END (Point 17)