User Manual

ManualsBrandsSiemens ManualsFire - Alarm EquipmentCAB-BATT / CAB-BATT-R Battery Box, Installation Instructions

Siemens Siemens

Siemens

IndustryIndustry

Industry

Inc. Inc.

Inc.

Building Building

Building

ecec

hnologies Dihnologies Di

hnologies Di

visionvision

vision

P/N 315-033917-10

INTRODUCTION The Model CAB-BATT/R Battery Box from Siemens Industry, Inc., is used to house

BTX-2 (55AH) batteries for MXL Systems; BTX-2 (55AH) batteries and BTX-3 (100AH)

batteries for FireFinder-XLS/Desigo Fire Safety Modular/Cerberus PRO Modular

Systems; and 100AH battery sets for the FS-250 and FS-250C Systems. The CAB-

BATT is black and the CAB-BATT-R is red. The CAB-BATT-R will be referred to in the

remainder of this document as the CAB-BATT.

The CAB-BATT consists of a door and a backbox, as shown in Figure 1. The door is

permanently hinged left.

The battery box can be placed on the floor directly underneath the fire panel enclo-

sure to which it supplies battery backup or it can be mounted on a flat surface with

four user-supplied bolts that are a maximum of

/8 inch in diameter. When used for

Seismic applications, the battery box must be placed on the floor and mounted to the

wall as described on page 2.

CAB-BATT

KNOCKOUTS FOR WIRING

CABB-BATT battery box is for indoor use only in dry environments.

INSTALLATION Prior to installation consider the following:

• Weight and size of the enclosure.

• Local codes.

Battery Box

Installation Instructions

Model CAB-BATT/R

Figure 1

CAB-BATT Enclosure

Summary of content (8 pages)

PAGE 1
Installation Instructions Model CAB-BATT/R Battery Box INTRODUCTION The Model CAB-BATT/R Battery Box from Siemens Industry, Inc., is used to house BTX-2 (55AH) batteries for MXL Systems; BTX-2 (55AH) batteries and BTX-3 (100AH) batteries for FireFinder-XLS/Desigo Fire Safety Modular/Cerberus PRO Modular Systems; and 100AH battery sets for the FS-250 and FS-250C Systems. The CABBATT is black and the CAB-BATT-R is red. The CAB-BATT-R will be referred to in the remainder of this document as the CAB-BATT.
PAGE 2
Install the battery box: 1. Select a clean, dry, shock and vibration free surface in a protected environment. 2. Position the battery box directly beneath the fire panel enclosure to which it will be wired. (Knockouts in the battery box may be needed to line up with the knockouts in the fire panel enclosure.) 3. Position the battery box so that it is clear of obstructions and the front door opens freely. 4.
PAGE 3
For installations using 100 AH batteries, mark, drill, and install the bottom bolt in the backbox marked “D”, as shown in Figure 2. 9. Tighten all bolts securely against the back wall of the battery box. 10. Place the batteries in the bottom of the CAB-BATT. 11. To complete the installation for Seismic applications, refer to the CAB-55 BRKT and CAB-100 BRKT Installation Instructions, P/N 315-050547. WIRING The main AC power line must be turned OFF prior to installation.
PAGE 4
(OPTIONAL) CC-5 TRANSFORMER CC-5 FS-MB / FS-MB2 TYPICAL CAB-2 ENCLOSURE TB1 P5 CC-5 + FS-NPE TAMPER SWITCH J1 FS-DLC ( FS-250) OR FDLC (FS-250C) - TB3 P4 TX-3 TO DISPLAY BOARD P10 PSC-12 RESET BRDG POWER MODULE FAIL CAN FAIL H - NET FAIL GND FAULT 24V 12 FAIL 24V 4A FAIL TX-2 HNET/CAN FS-NPE 1+ ON OFF BATTERY O — P9 TB2 _ + TB4 1 + P12 FS-DACT OR FS-MT TX-1 12+ 2- 3+ 3- GND N 2 _ 4+ H 4- H N GND P4 P1 H P5 PTB TB2 12 in.
PAGE 5
Cyber security disclaimer Siemens products and solutions provide security functions to ensure the secure operation of building comfort, fire safety, security management and physical security systems. The security functions on these products and solutions are important components of a comprehensive security concept. It is, however, necessary to implement and maintain a comprehensive, state-of-the-art security concept that is customized to individual security needs.
PAGE 6
THIS PAGE HAS BEEN LEFT INTENTIONALLY BLANK. Siemens Industry, Inc.
PAGE 7
THIS PAGE HAS BEEN LEFT INTENTIONALLY BLANK. Siemens Industry, Inc.
PAGE 8
Siemens Industry, Inc. Building Technologies Division Florham Park, NJ Siemens Canada, Ltd.