Data Sheet for Product

ManualsBrandsSiemens ManualsFire - Alarm EquipmentCAB1 / CAB1R System Enclosure, Installation Instructions

Siemens Data Sheet 7327

Building Technologies Division usa.siemens.com/desigo-fs-modular

Desigo® Fire Safety Modular

Enclosures and Equipment

CAB2-BD | CAB2-XBD | CAB2-XRD | CAB3-BB |

CAB3-BD | CAB3-XBD | CAB3-XRD | ID-MP | ID-SP

XLS-MLE6-ADPT | XLS-MME3-ADPT | XLS-MSE2-

ADPT | XLS-MSE3-ADPT –and– XLS-RCC13F-ADPT

Model CAB1-

One-row system enclosure

Architect & Engineer Specifications

 One (1) | two (2) | three (3)

row enclosure types

 Blank plates (ordered separately)

for inner and outer doors

 Clear lens and grill plates (sold

separately) for use with outer door

 UL 864 Listed, ULC Listed; FM (#3010),

CSFM (#7272-0067:0222) and NYCFD

(#6160) Approved

Product Overview

The enclosures used with Desigo Fire Safety Modular systems (Models CAB1,

CAB2, and CAB3), along with their accessories, provide a complete set of hardware

for mounting all main system and remote transponder cards and modules.

The hardware allows each DSFM system to be configured for a wide variety of

applications. Included in the enclosure series are backbox and door sets;

removable mounting plates and clear lenses; louvered ventilation grill plates, and

blank plates for use with the enclosure doors.

All enclosures come with ground straps for the inner and outer doors; shield

termination lugs; grounding lugs, and tie wrap lances for securing wire.

All enclosures can also mount system backup batteries up to 31AH in capacity.

Model CAB2-

[with mounted optional inner door]

Model CAB3-

[with mounted optional inner door]

Model REMBOX 4-

Model REMBOX 2-

Summary of content (6 pages)

PAGE 1
Desigo® Fire Safety Modular Enclosures and Equipment Models: BCM | CAB1 | CAB-BATT/-R | CAB-MP | CAB2-BB | CAB2-BD | CAB2-XBD | CAB2-XRD | CAB3-BB | CAB3-BD | CAB3-XBD | CAB3-XRD | ID-MP | ID-SP | OD-BP | OD-GP | OD-LP | REMBOX2 | REMBOX4 | XLS-MLE6-ADPT | XLS-MME3-ADPT | XLS-MSE2ADPT | XLS-MSE3-ADPT –and– XLS-RCC13F-ADPT Architect & Engineer Specifications  One (1) | two (2) | three (3) row enclosure types  Blank plates (ordered separately) for inner and outer doors  Clear lens and grill plates (sold
PAGE 2
Enclosures | Doors | Plates Single-Row Enclosure Model CAB1, the smallest of the Desigo Fire Safety Modular system enclosures, can house a single Model CAB-MP cabinet mounting plate for mounting card cages, power supplies and bulk amplifiers. Model CAB1 also has four (4) mounting slots on the inner door for mounting an Operator Interface (OI) and Model ID-MP switch module brackets.
PAGE 3
Enclosures | Doors | Plates – (continued) Cabinet Mounting Plate REMBOX2 (with doors closed) REMBOX2 -REMBOX2(with doors closed) (with doors open) Two-Module Remote Enclosure Model REMBOX2 has two (2) inner-door module spaces, and can hold on Desigo Modular OI, up to two (2) switch-module brackets, one (1) Model LVM. Combinations are permissible. Model REMBOX2 can also mount a single Model RNI on a bracket included in the backbox.
PAGE 4
Enclosures | Doors | Plates – (continued) Outer Door Inner Door Adapter Plate -Model OD-BPOuter Door Blank Plate The Outer Door Blank Plate (Model OD-BP) is used to cover an entire row of a Desigo Modular system cabinet. Model OD-BP is mounted when no module is used in that location. Model OD-BP is mounted on the outer door, and one (1) blank plate is included with each order.
PAGE 5
Details for Ordering MODEL OR TYPE PART NUMBER BCM Details for Ordering – (cont.
PAGE 6
NOTICE – The information contained in this data-sheet document is intended only as a summary, and is subject to change without notice. The product(s) described here has/have a specific instruction sheet(s) that cover various technical, limitation and liability information. Copies of install-type, instruction sheets – as well as the General Product Warning and Limitations document, which also contains important data, are provided with the product, and are available from the Manufacturer.