CDI-WAN MP2.
Data and design subject to change without notice. / Supply subject to availability. © Copyright by Siemens Building Technologies AG We reserve all rights in this document and in the subject thereof.
1 Introduction ......................................................................................................... 2 2 What’s new in MP2.1........................................................................................... 2 2.1 New products and improvements............................................................... 2 2.2 Compatibility with management stations.................................................... 2 2.3 New software tools.....................................................
1 Introduction This document applies to CDI-WAN MP2.1, which is now available for market distribution. The new product list includes: NK8222 Ethernet port (single) R1.0 NK8223 Ethernet port (multiple) R2.1 These Ethernet ports are to be used as network units for the following DMS hosts: MK8000 OPC server MP1.3; MM8000 management station MP2.3. CDI-WAN MP1.1, supporting LMSmodular, is still available. Please note that the ordering codes for NK8223 MP1.1 (R1.31) have changed. 2 What’s new in MP2.
In the Composer project, MK8000 and MM8000 should be configured to include the new CDI-WAN driver NS8210, which is one of the standard drivers available. Note: NS8210 actually replaces the NK8210 router that used to be installed with LMSmodular software. Limitations MK8000 and MM8000 cannot be connected to NK822x MP2.1 over serial line. A technical difficulty in the configuration tool currently causes this limitation, which will soon be removed. Serial-based solutions for MK8000 MP1.3 and MM8000 MP2.
2.4 New documentation The CDI-WAN documentation has changed significantly for this version, reflecting the integration into the new DMS line of products.
3 Migrating from a previous release 3.1 Verification Upgrading from previous MP1.0 (R1.01) and MP1.1 (R1.31) to MP2.1 is possible as long as you ensure the following: - The architecture includes a max.
NK8223 configuration Branch no.: ______________ Branch number, ranging from 1 to 50 IP address: IP address, subnet mask and default gateway address for the NK8223. Take note of the four 3-digit numbers (0-255). _______ . _______ . _______ . _______ Subnet mask: _______ . _______ . _______ . _______ Note: The default gateway may not be required (and left = 0.0.0.0) if the unit is in the same subnet as the central. Default gateway: _______ . _______ . _______ .
COM4: Control unit: _____________________________ Take note of the control unit, subsystem, or interface unit connected to the serial port (for example, CK11, MK722, CF-9000), as well as the communication protocol (such as Cerban, Cerloop, CMX-DL).
3.2.2 Updating NK8223 firmware The NK8223 software MP1.x should be updated with latest file set, which includes: File name CDDL.DLL CeiCa.DLL Cerban.DLL CerComD.DLL CMSDL.DLL CMSDLNet.DLL CMX.DLL I2CIO.DLL MK7022.DLL Monitor.DLL NK822x.EXE Disk386D.BIN Date 3/11/2003 3/11/2003 3/11/2003 3/11/2003 3/11/2003 3/11/2003 3/11/2003 3/11/2003 3/11/2003 3/11/2003 3/11/2003 23/04/2002 New in MP2.1 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No, same as in MP1.1 (R1.
Fig 1. IP settings for default configuration Firmware update: At that point, the new default configuration file (.INI) is installed on the NK8223. However, it is not used by the old firmware. In order to download the new firmware, you have to use the “Download file” command. Browsing on the files directories, locate and select the files listed above and select “open” to download them to the NK unit (Fig 2). Fig 2.
Using the reset command of NW8201 tool, you can achieve the result. See WAN Technical Manual MP1.x (001111_c_en). CDI- Composer configuration: In Composer, configure the NK8223 to update. See DMS8000 Connectivity Guide (007083_c_en) for detailed instructions. Select the NS8210 CDI-WAN driver node and then the “Firmware Update” tab. In the list of NK822x units, select the one you wish to download and click on the button “Download configuration” (Fig 3).
4 Compatibility matrices Supported in # Unit – Protocol CDI-WAN MP2.1? Management stations MK8000 MP1.3 MM8000 MP2.3 1. Burle CCTV – Allegiant Planned Planned Planned 2. Comerson CCTV – CDDL/CDSF No, use MP1.1 and LMS No No, use LMS 3. CDDL/CDSF compliant subsystem No, use MP1.1 and LMS No No, use LMS 4. FHI-PAD - CDDL/CDSF No, use GW20 and LMS No No, use LMS 5. CC30 CerPass – CerTalk No, use MP1.1 and LMS No No, use LMS 6. CC60 – Cerban Yes Yes Yes 7.
5 Known problems & bugs This is a list of known problems, limitations and bugs in MP2.1. For troubleshooting, see the troubleshooting documentation. See also 7 Support links and resources, on page 14 for links providing useful information. 1. 2. 3. 4. 5. CDI-WAN configurations made with NW8201 are not compatible with the new version and must be reintroduced in Composer projects for 2.1.
6 Documentation This section provides an overview of what information is included in each of the documents that accompany CDI-WAN MP2.1. 6.1 CDI-WAN Product Binders The product binders contain sales and technical documentation, respectively. The format reflects the standard for all FSP-DMS documents. 6.2 Sales documentation Product Datasheets These are 4-page documents to be used for introducing the NK822X Ethernet Ports to potential customers.
7 Support links and resources 7.1 CDI-WAN FSP-DMS support provides information on the Intranet site http://www.cdi.cerberus.ch/support/supp-lmsn.asp. A software troubleshooting guide is available at: http://www.cdi.cerberus.ch/support/supp-trou.asp (password required) or deliverable upon request, please contact CD-IT support: support@cdi.cerberus.ch. 7.2 Microsoft General support about Microsoft Windows can be found at: ⇒ http://support.microsoft.
Siemens Building Technologies AG Alte Landstr. 411 CH-8708 Männedorf Tel. +41 1 - 922 6111 Fax +41 1 - 922 6450 www.sibt.com Document no.