CL-010/CL-010-I ADSL2+ Router User’s Manual Rev: 1.5 2007/03/30 No part of this publication may be reproduced in any form by any means without the prior written permission. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies. This manual currently suits for CL-010/CL-010-I.
Safety Notes For Installation Use only the type of power source indicated on the marking labels. Use only power adapter supplied with the product. Do not overload wall outlet or extension cords as this may increase the risk of electric shock or fire. If the power cord is frayed, replace it with a new one. Proper ventilation is necessary to prevent the product overheating. Do not block or cover the slots and openings on the device, which are intended for ventilation and proper operation.
ADSL Router User Manual FCC FCC Class B Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Preface Thank you for choosing the Asymmetric Digital Subscriber Line (ADSL2+) Router. With the asymmetric technology, this device runs over standard copper phone lines. In addition, ADSL2+ allows you to have both voice and data services in use simultaneously all over one phone line. CL-010/CL-010-I ADSL2+ Router is a DSL broadband access device which allows ADSL2+ connectivity capabilities for home or office users.
ADSL Router User Manual ³ RFC2684 LLC Encapsulation and VC Multiplexing over AAL5 ³ RFC2364 Point-to-Point Protocol (PPP) over AAL5 ³ RFC2225 Classical IP and ARP over ATM ³ RFC2516 PPP over Ethernet: support Relay (Transparent Forwarding and Client functions) ³ Support PPPoA or PPPoE Bridged mode (the IP address got from ISP can be passed to the user’s PC and behave as the IP address of the user’s PC.
³ Firmware upgrades through HTTP, TFTP, or FTP ³ The boot loader contains very simple web page to allow the users to update the run-time firmware image. ³ Configuration file backup and restore ³ SNMPv1/v2 agent with MIB-II, ADSL Line MIB Unpacking Check the contents of the package against the pack contents checklist below. If any of the items is missing, then contact the dealer from whom the equipment was purchased.
ADSL Router User Manual Subscription for ADSL Service To use the ADSL Router, you have to subscribe for ADSL service from your broadband service provider. According to the service type you subscribe, you will get various IP addresses: Dynamic IP: If you apply for dial-up connection, you will be given an Internet account with username and password. You will get a dynamic IP by dialing up to your ISP.
Chapter 1: Overview Chapter 1: Overview This chapter provides you the description for the LED and connector for front and rear view of the router. Before you use/install this router, please take a look at this information first.
Rear Panel The following figures illustrate the rear panel of your ADSL Router.
Chapter 2:System Requirement and Installation Chapter 2: System Requirement and Installation System Requirement To access the ADSL Router via Ethernet, the host computer must meet the following requirements: With Ethernet network interface. Must have TCP/IP installed. Set client PC with obtain an IP address automatically or set fix IP address. With a web browser installed: Internet Explorer 5.x or later. The ADSL Router is configured with the default IP address of 192.168.1.
Connecting the ADSL Router Follow the steps below to connect the related devices. n o p q r Connecting the ADSL line. Connect the DSL port of the device to your ADSL wall outlet with RJ-11 cable. Please attach one end of the Ethernet cable with RJ-45 connector to the LAN port of your ADSL Router. Connect the other end of the cable to the Ethernet port of the client PC. Connect the supplied power adapter to the PWR port of your ADSL Router, and plug the other end to a power outlet.
Chapter 3: Configuration For connecting through a hub, please refer to the following diagram for an example. 9 VAC Setting TCP/IP In order to access the Internet through the router, each host on your network must install/setup TCP/IP. Please follow the steps below for select a network adapter.
For Windows 98 1. Click on the Start menu, point to Settings and click on Control Panel. 2. Double-click the Network icon 3. The Network window appears. On the Configuration tab, check out the list of installed network components. Option 1: If you have no TCP/IP protocol, click Add. Option 2: If you have TCP/IP protocol, go to Step 6 Your network interface card. Check out if TCP/IP for your NIC is installed or not. 4. Highlight Protocol and click Add.
Chapter 3: Configuration 5. On the left side of the windows, highlight Microsoft and then select TCP/IP on the right side. Then click OK 6. When returning to Network window, highlight TCP/IP protocol for your NIC and click Properties. 7. On IP Address tab: Enable Specify an IP address option. Enter the IP Address: 192.168.1.x (x is between 2 and 254) and Subnet Mask: 255.255.255.0 as in figure below. On Gateway tab: Add a gateway IP address: 192.168.1.
8. When returning to Network window, click OK 9. Wait for Windows copying files. 10. When prompted with System Settings Change dialog box, click Yes to restart your computer.
Chapter 3: Configuration For Windows ME 1. 2. 3. 4. 5. 6. Click on the Start menu, point to Settings and click on Control Panel. Double-click the Network icon. The Network window appears. On the Configuration tab, check out the list of installed network components. Option 1: If you have no TCP/IP protocol, click Add. Option 2: If you have TCP/IP protocol, go to Step 6. Highlight Protocol and click Add. On the left side of the windows, highlight Microsoft and then select TCP/IP on the right side.
9. Wait for Windows copying files. 10. When prompted with the System Settings Change dialog box, click Yes to restart your computer. For Windows NT 1. Click Start, point to Settings, and then click Control Panel. 2. Double-click the Network icon. 3. The Network window appears. On the Protocols tab, check out the list of installed network components. Option 1: If you have no TCP/IP Protocol, click Add. Option 2: If you have TCP/IP Protocol installed, go to Step 7. 4.
Chapter 3: Configuration 5. Click Yes to use DHCP. 6. Insert the Windows NT CD into your CD-ROM drive and type the location of the CD. Then click Continue. 7. Returning to the Network window, you will find the TCP/IP Protocol among the list. Select TCP/IP Protocol and click Properties. 8. Enable Specify an IP address option. Enter the IP Address: 192.168.1.x (x is between 2 and 254) and Subnet Mask: 255.255.255.0 and Default Gateway: 192.168.1.1 as in figure below.
9. When returning to Network window, click Close. 10. When prompted with Network Settings Change dialog box, click Yes to restart your computer.
Chapter 3: Configuration For Windows 2000 1. From the Start menu, point to Settings and then click Network and Dial-up Connections. 2. Right-click the Local Area Connection icon and then click Properties. 3. On the General tab, check out the list of installed network components. Option 1: If you have no TCP/IP Protocol, click Install. Option 2: If you have TCP/IP Protocol, go to Step 6.
4. Highlight Protocol and then click Add. 5. Click Internet Protocol (TCP/IP) and then click OK. 6. When returning to Local Area Connection Properties window, highlight Internet Protocol (TCP/IP) and then click Properties. 7. Under the General tab, enable Use the following IP Address. Enter the IP address: 192.168.1.x (x is between 2 and 254), Subnet Mask: 255.255.255.0 and Default gateway: 192.168.1.1. Then click OK.
Chapter 3: Configuration For Windows XP From the Start menu, point to Control Panel and then click Network and Internet Connections. Click Network Connection and then click Properties. Click Network Connection and then click Properties.3.On the General tab, check out the list of installed network components. Option 1: If you have no TCP/IP Protocol, click Install. Option 2: If you have TCP/IP Protocol, go to Step 6. Highlight Protocol and then click Add. Click Internet Protocol(TCP/IP) and then click OK.
For Windows Vista 8. Open the Start menu, point to Control Panel and click it. 9. Click Network and Internet. 10. Select Network and Sharing Center.
Chapter 3: Configuration 11. Click Manage Network Connection on the left side. 12. Right click Local Area Connection and select Properties. 13. On the Networking tab, you will find Internet Protocol Version 6 and Version 4. Contact your ISP to confirm which one will be used. (We take TCP/IPv4 for example here.) Select Internet Protocol Version 4 (TCP/IPv4) and press Properties.
14. Under the General tab, enable Use the following IP address. Enter the IP address: 192.168.1.x (x is between 2 and 254), Subnet Mask: 255.255.255.0 and Default gateway: 192.168.1.1. Then click Ok. Renewing IP Address on Client PC After the ADSL Router gets on line, there is a chance that your PC does not renew its IP address and thus causes the PC not able to access the Internet. To solve this problem, please follow the procedures below to renew PC’s IP address.
Chapter 3: Configuration On the IP Address tab, select Obtain an IP address automatically. Then click OK. For Windows ME On the IP Address tab, select Obtain an IP address automatically. Then click OK.
For Windows NT On the IP Address tab, click on the drop-down arrow of Adapter to select required adapter. Enable Obtain an IP address from a DHCP server and then click OK.. When prompted with the message below, click Yes to continue. For Windows 2000 Enable Obtain an IP address automatically and then click OK.
Chapter 3: Configuration For Windows XP On the IP Address tab, select Obtain an IP address automatically. Then click OK. Windows Vista On the IP Address tab, select Obtain an IP address automatically. Then click OK.
Renew IP Address on Client PC There is a chance that your PC does not renew its IP address after the ADSL Router is on line and the PC cannot access the Internet. Please follow the procedures below to renew PC’s IP address. For Windows 98ME 1. Select Run from the Start menu. 2. Type winipcfg in the dialog box and the click OK. 3. When the figure below appears, click Release and then Renew to get an IP address. For Windows NT 1. Select Run from the Start menu.
Chapter 3: Configuration 2. Select Run from the Start menu. 3. Type cmd in the dialog box and the click OK. 4. Type ipconfig at prompt. Then you will see the IP information from DHCP server. If you want to get a new IP address, type ipconfig /release to release the previous IP address and then type ipconfig /renew to get a new one. 5.
For Windows 2000 1. 2. 3. From the Start menu, point to Programs, Accessories and then click Command Prompt. Type ipconfig at prompt. Then you will see the IP information from DHCP server. If you want to get a new IP address, type ipconfig /release to release the previous IP address and then type ipconfig /renew to get a new one. For Windows XP 1. 2. 3. 4. Type ipconfig at prompt. Then you will see the IP information from DHCP server.
Chapter 3: Configuration For Windows Vista 1. Open the Start menu, and type cmd in the text box then click OK. 2. The command prompt window will appear. 3. Type ipconfig at the command window and press Enter to view the computer’s IP information from DHCP server. 4. If the computer is holding a current IP address, type ipconfig /release to let go of the address, then type ipconfig /renew to obtain a new one.
Note: If you cannot release the IP address successfully and see the message “The requested operation requires elevation,” please go to the Start menu and right click Command Prompt, then set Run as administrator. Press Continue when a dialog asking for permission to continue prompts. After then, repeat the above instruction to release and renew the IP address.
Chapter 3:Connecting and Accessing Internet Chapter 3: Connecting and Accessing Internet This chapter is to help you accessing into Internet with a quick and convenient way. If you need more detailed information for web configuration, please get into the next chapter for the advanced configuration. Prior to configuring the ADSL Router, you must decide whether to configure the ADSL Router as a bridge or as a router. This chapter presents some deployment examples for your reference.
PPP over ATM (PPPoA) Mode Default Private IP 192.168.1.1 Dynamic Public IP assigned by BRAS ISP 192.168.1.3 STM-1 Loop (Internet Service Provider) Ethernet BRAS AAA DSLAM RDAIUS Server *BRAS: Broadband Remote Access Server ADSL Router Hub 192.168.1.2 PPP over ATM PC(S) PPPoA+NAT+DHCP on Private LAN Description: In this deployment environment, the PPPoA session is between the ADSL WAN interface and BRAS. The ADSL Router gets a public IP address from BRAS when connecting to DSLAM.
Chapter 3:Accessing Internet PPP over ATM (PPPoA) IP Extension Mode Default Private IP 192.168.1.1 Dynamic Public IP assigned by BRAS ISP Loop STM-1 (Internet Service Provider) Ethernet BRAS AAA DSLAM ADSL Router Hub PC RDAIUS Server *BRAS: Broadband Remote Access Server PPP over ATM PPPoA+NAT+DHCP on Private LAN Description: In this deployment environment, the PPPoA session is between the ADSL WAN interface and BRAS.
PPP over Ethernet (PPPoE) Mode Default Private IP 192.168.1.1 Dynamic Public IP assigned by BRAS ISP 192.168.1.3 STM-1 (Internet Service Provider) Loop Ethernet BRAS AAA DSLAM ADSL Router 192.168.1.2 RDAIUS Server *BRAS: Broadband Remote Access Server Hub PC(S) PPP over Ethernet PPPoE+NAT+DHCP on Private LAN Description: In this deployment environment, the PPPoE session is between the ADSL WAN interface and BRAS. The ADSL Router gets a public IP address from BRAS when connecting to DSLAM.
Chapter 3:Accessing Internet PPP over Ethernet (PPPoE) IP Extension Mode Default Private IP 192.168.1.1 Dynamic Public IP assigned by BRAS ISP (Internet Service Provider) Loop STM-1 BRAS DSLAM AAA Ethernet ADSL Router Hub PC(S) RDAIUS Server *BRAS: Broadband Remote Access Server PPP over Ethernet PPPoE IP Extension Mode Description: In this deployment environment, the PPPoE session is between the ADSL WAN interface and BRAS.
Numbered IP over ATM (IPoA) Default Private IP 192.168.1.1 ISP (Internet Service Provider) STM-1 Loop S/W 10.3.70.1 BRAS AAA DSLAM ADSL Router Hub 10.3.75.50 RDAIUS Server *BRAS: Broadband Remote Access Server 10.3.75.51 10.3.75.49 PC(S) IP over ATM Public IP Pre-assigned by ISP Description: If you apply for multiple IP addresses from your ISP, you can assign these public IP addresses to the ADSL Router and public server, e.g., Web or FTP server.
Chapter 3:Accessing Internet 7. Check the network information. Make sure the settings match the settings provided by ISP. Click Finish. 8. Set TCP/IP for your computer. Specify an IP Address, subnet mask and set default gateway. eg: IP Address: 10.3.75.51 Subnet Mask: 255.255.255.248 Gateway: 10.3.75.49 9. Now the router is well configured. You can access into Internet.
Numbered IP over ATM (IPoA)+NAT Description: In this deployment environment, we make up a private IP network of 192.168.1.1. NAT function is enabled (on ADSL Router or use another NAT box connected to hub) to support multiple clients to access the Router and some public servers (WWW, FTP). If you apply for multiple IP addresses from your ISP, you can assign these public IP addresses to the ADSL Router and public server, e.g., Web or FTP server.
Chapter 3:Accessing Internet LAN. Primary IP Address: 192.168.1.1 Subnet mask: 255.255.255.0 Start IP Address: 192.168.1.2 End IP Address: 192.168.1.254 7. Check Configure the second IP Address and Subnet Mask for LAN Interface and type in the second IP address and subnet mask. Then click Next. Secondary IP Address: 10.3.75.49 Subnet mask: 255.255.255.248 8. Check the network information. Make sure the settings match the settings provided by ISP. Click Finish. 9. Now the router is well configured.
Unnumbered IP over ATM (IPoA) Default Private IP 192.168.1.1 ISP (Internet Service Provider) STM-1 Loop 10.3.75.51 10.3.75.49 S/W BRAS AAA DSLAM ADSL Router 10.3.75.50 RDAIUS Server *BRAS: Broadband Remote Access Server Hub PC(S) IP over ATM Public IP Pre-assigned by ISP Description: If you apply for multiple IP addresses from your ISP, you can assign these public IP addresses to the ADSL Router and public server, e.g., Web or FTP server.
Chapter 3:Accessing Internet 8. Set TCP/IP for your computer. Specify an IP Address, subnet mask and set default gateway. eg: IP Address: 10.3.75.51 Subnet Mask: 255.255.255.248 Gateway: 10.3.75.49 9. Now the router is well configured. You can access into Internet.
Unnumbered IP over ATM (IPoA)+NAT Description: If you apply for multiple IP addresses from your ISP, you can assign these public IP addresses to the ADSL Router and public server, e.g., Web or FTP server. Typically the first IP is network address, the second is used as router IP address and the last one is subnet broadcasting. Other remaining IP addresses can be assigned to PCs on the LAN. The following example uses the LAN IP address ranging from 10.3.75.49 to 10.3.75.
Chapter 3:Accessing Internet Start IP Address: 192.168.1.2 End IP Address: 192.168.1.254 7. Check Configure the second IP Address and Subnet Mask for LAN Interface and type in the second IP address and subnet mask. Then click Next. Secondary IP Address: 10.3.75.49 Subnet mask: 255.255.255.248 8. Check the network information. Make sure the settings match the settings provided by ISP. Click Finish. 9. Now the router is well configured. You can access into Internet.
Bridge Mode Default Private IP 192.168.1.1 ISP Loop STM-1 (Internet Service Provider) BRAS AAA DSLAM PPPoE Client S/W ADSL Router RDAIUS Server *BRAS: Broadband Remote Access Server Hub PC(S) PPP over Ethernet Bridge Mode Description: In this example, the ADSL Router acts as a bridge which bridging PC IP address from LAN to WAN.
Chapter 5:Connection Mode Chapter 4: Web Configuration Some users might want to set specific configuration for the router such as firewall, data transmission rate… and so on. This chapter will provide you advanced information of the web pages for the router for your reference. Using Web-Based Manager Once your host PC is properly configured, please proceed as follows: 1. Start your web browser and type the private IP address of the ADSL Router in the URL field: 192.168.1.1. 2.
Outline of Web Manager For configure the web page, please use admin as the username and the password. The main screen will be shown as below. Title: It indicates the title of this management interface. Main Menu: Includes Quick Start, Status, Advanced and Management. Main Window: It is the current workspace of the web management, containing configuration or status information.
Chapter 5:Connection Mode Quick Start The pages for the Quick Start provide user a quick way to set for the router. If you do not know more about the router, you can use the Quick Start pages to adjust basic settings to make your router activating. Connect to Internet This is a quick way to connect to Internet by using PPPoE interface, click Connect to Internet to open the web page. Enter the user name and password for your ADSL router and click Connect.
After clicking on the Next button from the VPI/VCI web page, the following screen will appear. Please choose the connection type and encapsulation mode that you want to use and click Next for next page. For example, PPP over Ethernet (PPPoE) in this screen is selected. Next, we are going to tell you different webpage for different protocol that you choose in this page.
Chapter 5:Connection Mode PPP over ATM/ PPP over Ethernet If the type you choose is PPP over ATM or PPP over Ethernet, please refer to the following information. According to the ISP’s configuration on the server, you can choose PPPoE and PPPoA modes. If the ISP provides PPPoE service, the connection type selection will be decided as whether the LAN side device is running a PPPoE client or the router is to run the PPPoE client. This router supports both situations simultaneously.
PPP Username: Type in the username that you got from your ISP. PPP Password: Type in the password that you got from your ISP. Always On: Check this button to make the connection is always active. Dial on Demand: Click this button to make a connection while Please type the username and password that you got in demand. Enter the timeout to cut off the network connection if there is no activity for from your ISP. Then click Next. this router.
Chapter 5:Connection Mode PCs. Start IP Address: Type in the start point IP address. End IP Address: Type in the end point IP address. Leased Time: Type in the duration for the time. The default is 1day. DHCP Server Off: Check this item if DHCP service isn’t needed on the LAN. You can check it at this time. If you find something is incorrect, click Back to change the settings. If everything is OK, click Finish to accept these settings.
IP over ATM If the type you have to choose is IP over ATM, please refer to the following information. IPoA is an alternative of LAN emulation. It allows TCP/IP network to access ATM network and uses ATM quality of service’s features. Choose IPoA and click Next. None: If it is not necessary to set the WAN IP address, please click this button. Obtain an IP address automatically: Click this button to make the system get an IP address automatically.
Chapter 5:Connection Mode In the Configure LAN side Settings web page, you have to fill in the data requested here. Primary IP Address: Type in the first IP address that you got from your ISP for your LAN connection. Subnet Mask: Type in the subnet mask that you got from your ISP for your LAN connection.
Now, the system will reboot to activate the new settings that you have done in this section. Please wait for 2 minutes for restarting the router.
Chapter 5:Connection Mode Bridging If the type you choose is Bridging, please refer to the following information. The bridging mode can configure your router to send packets received on any port such as ATM PVC or Ethernet with a broadcast MAC address to all other ports. Choose Bridging and click Next. None: If it is not necessary to set the WAN IP address, please click this button. Obtain an IP address automatically: Click this button to make the system get an IP address automatically.
Primary IP Address: Type in the IP address that you got from your ISP for LAN interface. Subnet Mask: Type in the subnet mask that you got from your ISP for LAN interface. MTU: It means the maximum size of the packet that transmitted in the network. The packet of the data greater than the number set here will be divided into several packets for transmitting. Type in the number into the field of MTU. The default setting is 1500. DHCP Server On: Check this item if DHCP service is needed on the LAN.
Chapter 5:Connection Mode Status Overview This page is displaying the current status for the DSL connection. It includes if the lists the LAN IP address, default gateway, DNS servers IP address, firmware version, the period of activating the router, and so on. The system status will be changed according to the settings that you configured in the web pages.
ADSL Line This page shows all information for ADSL. For knowing the quality of the ADSL connection, please click ADSL BER Test button to have advanced information. Click More Information to show more detailed information about ADSL Line Status. ADSL BER Test This test determines the quality of the ADSL connection. It is done by transferring idle cells containing a known pattern and comparing the received data with this known pattern to check for errors.
Chapter 5:Connection Mode When the test is over, the result will be shown on the following dialog for your reference. Click Close to close this dialog. Internet Connection This page displays the connection information for your router, such as PVC name, category, protocol, invoking NAT or not, IP address, link status and so on. Traffic Statistics This table shows the records of data going through the LAN and WAN interface. For each interface, cumulative totals are displayed for Received and Transmitted.
This table shows the IP address record for IP-to-Physical translation in your router.
Chapter 5:Connection Mode Advanced Setup Local Network- IP Address This page is the same as you can see in the Configure LAN side Settings page while running the Quick Setup. It allows you to set IP Address and Subnet Mask values for LAN interface. Primary IP Address: Type in the first IP address that you got from your ISP for your LAN connection. Subnet Mask: Type in the subnet mask that you got from your ISP for your LAN connection. Host Name: List the host name of this device.
DHCP Server On: Check this item if DHCP service is needed on the LAN. The router will assign IP address, gateway address for each of your PCs. Start IP Address: Type in the start point IP address. End IP Address: Type in the end point IP address. Leased Time: Type in the duration for the time. The default is 1day. Relay On: Click this button to have a relay setting. And type in the Server IP in this field. Server and Relay Off: Check this item if DHCP service isn’t needed on the LAN.
Chapter 5:Connection Mode The new one will be shown on the dialog right away. That is, the specified address will be reserved and not be assigned by DHCP for other computer.
Local Network – UPnP The UPnP is available only for Windows XP. If you are not user of Windows XP, this page does not have any meaning to you. This page allows you to enable the UPnP function through the web page for your router. Internet-Connections Setting To set WAN settings for each service, please open Advanced– Internet Setting. This page allows you to add new WAN settings, to edit or remove created WAN settings.
Chapter 5:Connection Mode If you choose Non Realtime VBR, you have to type in the following data. The range for Peak Cell Rate is from 1 to 1690. The range for Sustainable Cell Rate is from 1 to 1689 and must be smaller than Peak Cell Rate. The range for Maximum Burst Size is from 1 to 100. After click Next, you will see the web page listed as the right. Choose the protocol that you want. And click Next again. The WAN IP settings will differ slightly according to the protocol that you choose.
Internet-DNS Server If Enable Automatic Assigned DNS checkbox is selected, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment. If the checkbox is not selected, it is necessary for you to enter the primary and optional secondary DNS server IP addresses. After type in the address, click Apply button to save it and invoke it.
Chapter 5:Connection Mode Internet - ADSL Settings Enable ADSL Port: Check this box to enable this function. It simply invokes the line mode that you choose here for the router. Select the support of line modes: There are several selections for your choosing. Select the one that you need. For Example, if you want to change one or more physical layer parameters while the ATU-x is in data transfer state, and the transmission errors will not be present, please choose ADSL2.
Allow you to remove the selected static route settings. Adding a New One To add a static route, please choose Static Route - Add. Type the destination network address, subnet mask and gateway that you get from ISP and click Apply. Destination Network Address: The destination IP address of the network where data packets are to be sent. Subnet Mask: Type in the subnet mask that you got from ISP. Gateway IP Address: Click this button to invoke this function. Type in the gateway that you got from ISP.
Chapter 5:Connection Mode For a router with a direct connection to the Router’s local Router, the Gateway IP Address is the address of the Router’s local router. For routers which must forward packets to another router before reaching the Router’s local router, the Gateway IP Address is the address of the intermediate router. Example – Static Route Here provides you an example of Static Route.
different interface. Otherwise, disable this function. Click Apply to invoke the settings set here.
Chapter 5:Connection Mode Virtual Server-Port Forwarding The Router implements NAT to let your entire local network appear as a single machine to the Internet. The typical situation is that you have local servers for different services and you want to make them publicly accessible. With NAT applied, it will translate the internal IP addresses of these servers to a single IP address that is unique on the Internet.
IP Address seen by Internet Users Please note that, in the above picture, both Internet users are connecting to the same IP address, but using different protocols. To Internet users, all virtual servers on your LAN have the same IP Address. This IP Address is allocated by your ISP. This address should be static, rather than dynamic, to make it easier for Internet users to connect to your Servers.
Chapter 5:Connection Mode From Internet Host IP Address: Select the initial place for port forwarding. If you choose SINGLE, a box will appear for you to fill in the IP address for the specific host. And, if you choose SUBNET, the boxes of IP and Subnet will appear for you to fill in the IP address and subnet mask for the specific host as the start point. Forwarded to Internet Host IP Address: Type in the address for the host used as the place that information will be forwarded.
Or define by yourself by typing the words into the field of User defined. Click Apply to complete the setting. Virtual Server - DMZ Host Direct Mapping Zone (DMZ) uses a technology that makes Router forwarding all incoming packet to internal specific server. To close the function of DMZ Host, please click Discarded. To activate a DMZ host, please click Forwarded to the DMZ host radio button and type the IP Address into the field of IP address of DMZ host, then click Apply.
Chapter 5:Connection Mode Virtual Server - Dynamic DNS The Dynamic DNS (Dynamic Domain Nasme System) combines both functions of DNS and DHCP to map a dynamic IP into a fixed domain name. This page allows you to access into virtual servers with a domain name and password. Dynamic DNS： Selects Enable to enable DDNS; select Disabled to disable this function. Internet Connection： Selects the interface that you want to use for connecting Internet. User Name： Type in the user name that you registered in www.
Firewall The firewall is a software that interrupts the data between the Internet and your computer. It is the TCP/IP equivalent of a security gate at the entrance to your company. All data must pass through it, and the firewall (functions as a security guard) will allow only authorized data to be passed into the LAN.
Chapter 5:Connection Mode Then, to add a new IP Filtering, click Add. This page provides some settings for you to adjust for adding a new outbound IP Filtering. Allow Traffic: No stops the data transmission, Yes lets the data pass through. Protocol: Here provide several default policies for security levels for you to choose. If you don’t want to use the predefined setting, you can use User Defined to set a customized protocol for your necessity.
A new IP filtering setting for Outbound traffic is created in the web page. To edit the setting, please click the pencil mark to get into the editing page. To delete the setting, click the trash mark to erase it. To set another IP filtering, click Add again. For adding a new Inbound IP Filtering, click Inbound traffic in the item of Select the direction to filter packets. Use the same way to add a new one as stated above.
Chapter 5:Connection Mode is the default setting. IP type of Service: The system provides some types of service for you to choose. The meaning of each type is the same as the denotation. The default one is No change. IPQoS To classify the upstream traffic by assigning the transmission priority of the data for different users, please use IP QoS to prioritize the data transmission. The IP QoS allows you to set the settings based on layer three IP packets.
you want to invoke the QoS traffic rule. Destination Port: Type in the destination port for the traffic rule. The range is from 0 to 65535. Traffic Priority: There are three options – Low, Medium, and High that you can choose. It decides the order of each data transmitted through this device. IP Precedence: The number you choose here decides the type of the IP address processed. No change is the default setting. IP type of Service: The system provides some types of service for you to choose.
Chapter 5:Connection Mode Group Name: Type in a name here as a group name. It must be unique. The word length must not be over the length of the field. Available Interfaces: The available interfaces (such as Ethernet) will be displayed in the left side box. When you choose it and click Add, it will be transferred into the right side box of Grouped Interfaces.
Chapter 5:Connection Mode Management Diagnostics To check the link status for the network and your computer, a diagnostic test can guide you to detect the network problem. The testing items are listed and accomplished one by one. If the previous one is failed, than the items below that failed one will be failed too. Use this diagnostic test to detect the connectivity mistakes whenever you happen to the linked problem.
Chapter 5:Connection Mode Admin Account This page allows you to type in the password for accessing into your DSL Router. For the Admin Account, the default setting for user password is admin. If you want to change the username and the password, please retype the new password in the Confirm field for confirmation. Then click Apply. Remote Access There are four interfaces for the remote access. Please choose one of them if you want to enable the remote access control.
Interntet Time The router’s clock must synchronize with global Internet’s time. The time you set in the screen will be adapted to system log. Update: Click this button to refresh the current time. Set Time by: The default setting is Manual. If you select Time Server, you don’t need to type in the time setting manually. The system will set automatically. Time: Set the start time by typing the year, the month, the day, the hour, and the date to help the router perform tasks.
Chapter 5:Connection Mode There are 8 types for log level and display level for your choose. The default is Debugging. The mode selection includes Local, Remote and Both. The default one is Local. If you choose Remote or Both, all the events will be sent to the specified UDP port of the specified log server. Viewing System Log For viewing the system log, please click the View System Log button. The screen will be shown immediately for your reference.
SNMP Setting The SNMP, the abbreviation of Simple Network Management Protocol, is used to refer to a collection of specifications for network management that include the protocol itself, the definition of data structures and associated concepts. A management station performs the monitoring function by retrieving the value of MIB objects. The management station and agents are linked by a network management protocol that is SNMP. The SNMP includes three key capabilities, get, set and trap.
Chapter 5:Connection Mode workstation by way of SNMP agent. Backup Config To backup your configuration for the router to your computer, you can use Backup Config web page to save the settings. And when you want to restore the settings in the future, simply open Backup Config web page and use Browse button to locate the file and click Restore.
UPnP for XP Universal plug and play (UPnP) is an architecture for pervasive peer to peer network connectivity of intelligent appliances and PCs of all form factors. It is designed to bring easy-to-use, flexible, standards-based connectivity to ad-hoc or unmanaged networks whether in the home, in a small business, public spaces, or attached to the Internet. Only Windows XP supports UPnP function. Please follow the steps below for installing UPnP components. 1.
Chapter 5:Connection Mode 7. Now, the NAT traversal function will be provided. The ADSL router will create a new virtual server automatically for mapping while the router detecting the computer running some Internet applications.
Chapter 5:Troubleshooting Chapter 5: Troubleshooting If the suggested solutions in this section do not resolve your issue, contact your system administrator or Internet service provider. Problems with LAN PCs on the LAN cannot get IP addresses from the ADSL Router. The chances are that the interface used as DHCP server is modified and the client PCs do not renew IP addresses.
Chapter 6: Troubleshooting Request time out Then the DNS is not reachable. Check your DNS setting on the ADSL Router. Problems with Upgrading The following lists the error messages that you may see during upgrading and the action to take. Error: All the ADSL LEDs light up and cannot light off as usual. Possible cause: When users execute firmware upgrade and save settings to the router, the power for the router is lost for some unknown reasons, the normal web page for the router might be damaged.
Chapter 6: Glossary Chapter 6: Glossary ARP (Address Resolution Protocol ) ARP is a TCP/IP protocol for mapping an IP address to a physical machine address that is recognized in the local network, such as an Ethernet address. A host wishing to obtain a physical address broadcasts an ARP request onto the TCP/IP network. The host on the network that has the IP address in the request then replies with its physical hardware address.
Chapter 7: Glossary configured and mapped to a private workstation address when accesses are made through the gateway to a public network. For example, the ADSL Router is assigned with the public IP address of 168.111.2.1. With NAT enabled, it creates a Virtual LAN. Each PC on the Virtual LAN is assigned with a private IP address with default value of 192.168.1.2 to 192.168.2.254. These PCs are not accessible by the outside world but they can communicate with the outside world through the public IP 168.
the cells belonging to the same connection can be distinguished. A unique and separate VPI/VCI identifier is assigned in advance to indicate which type of cell is following, unassigned cells, physical layer OAM cells, metasignaling channel or a generic broadcast signaling channel. Your ISP should supply you with the values.
Chapter 7: Glossary
Appendix A: Specifications Appendix A: Specifications Interface z z z Regulatory Approvals and Compliance One RJ-11 port for ADSL connection Four RJ-45 ports for IEEE 802.3/802.
Appendix A: Specifications
Appendix B: Server Setup for 802.1x Client Appendix B: Server Setup for 802.1x Client Getting Client Certificate 1. 2. 3. 4. Please connect the client to a network that doesn’t require port authentictaion. Open up Microsoft Explorer in Windows XP, and go to http:///certsrv. Authenticate to the server using your account that you created at the end of the server setup. (e.g. 123) and click OK. A dialog box might appear for you to choose.
Appendix C: WEEE – B2C 5. Make sure that User certificate request: User Certificate is selected, and click Next. 6. Click Submit in this dialog. 7. Now, you'll see status messages on the screen, then your certificate will be returned to you. Click Install this certificate. 8.
Appendix C: WEEE – B2C All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. The correct disposal and separate collection of your old appliance will help prevent potential negative consequences for the environment and human health. It is a precondition for reuse and recycling of used electrical and electronic equipment.
