DG80025 DG10025 DG12025 DG15025
1 2 1 2 3 4 5 DG ...
5 6 B A Type 7 A B C E mm mm mm mm DG 80 DG 100 DG 120 DG 150 836 841 900 988 993 900 1148 1153 300 900 1378 1383 300 1000 II
DG 120../150.. DG 80../100..
11 12 13 13.
14 15 V
Empfohlene Anschlussarten Zweikreis / Recommended Configurations - Double-power E1 16 17 18 19 In jedem Fall kann die Variante 19 nicht mit E4-Anschluss verwendet werden. In any case, the variant 19 cannot be used with E4 connection.
Empfohlene Anschlussarten Einkreis / Boiler Betrieb Recommended Configurations - Single-power / Boiler mode operation E1 16 VII
de Allgemeine Hinweise • Das vorliegende Handbuch ist als fester und wesentlicher Bestandteil des Produktes zu verstehen. Es ist sorgfältig und stets griffbereit in Nähe des Gerätes aufzubewahren (auch im Falle der Übergabe an einen anderen Besitzer oder Nutzer und/oder der Übertragung auf eine andere Anlage). • Lesen Sie die Anweisungen und Hinweise, die dieses Handbuch gibt, aufmerksam durch, da sie wichtige Angaben zur Sicherheit bei Installation, Gebrauch und Wartung liefern.
• Der Warmwasser Wandspeicher ist für den geschlossenen (druckfesten) und offenen (drucklosen) Betrieb Geschlossener (druckfester) Betrieb Es sind geeignete Sicherheitsventil-Kombinationen bzw.
Wandmontage (Seite II, Bilder 6 bis 9) Die Montageschablone ist auf der Verpackung. Zum Wechseln von Heizflansch und Korrosionsschutz-Anode muss unterhalb des Speichers ein Platz von mindestens 500 mm frei bleiben. Geeignete Schrauben mit mindestens 12 mm Durchmesser verwenden. Bei Leichtbau-Wänden eine spezielle Tragekonstruktion vorsehen. DG120 und DG150 mit beiden Halterungen montieren. DG80 und DG100 mit dem Wandabstandhalter C senkrecht ausrichten.
Elektroanschluss Stromschlaggefahr! Der Leistungsschalter „S1“ darf nur im Stromlosen Zustand betätigt werden!! Geräte Unterkappe abnehmen, dazu Schrauben herausdrehen (Seite IV, Bild 13, 13.1) Kabel durch Kabelverschraubung und Zugentlastung führen und anschließen, danach Kabelverschraubung und Zugentlastung festziehen.
Einkreis Abhängig von der Hausinstallation sind folgende Anschlussvarianten möglich: Siehe Tabelle empfohlene Anschlussarten Einkreisschaltung (Seite VII) Leistungsschalter „S1“ auf der Elektronik in die Positionen 1 / 2 / 3 / 4 „Einkreis“ Schaltung einstellen Boiler Abhängig von der Hausinstallation sind folgende Anschlussvarianten möglich: Siehe Tabelle empfohlene Anschlussarten Boilerschaltung (Seite VII) Leistungsschalter „S1“ auf der Elektronik in die Positionen 8 / 9 / 0 „Boiler“ Schaltung einstellen.
Technische Daten DG80025 DG10025 DG12025 DG15025 Liter 80 100 120 150 kg 106 133 162 197 Modell Inhalt Gewicht gefüllt Mpa (bar) zulässiger Betriebsüberdruck Aufheizzeit in Stunden bei Kaltwasserzulauf von ca.
Eine Störung, was tun Funktioniert Ihr Gerät nicht wie gewünscht, so liegt es oft nur an einer Kleinigkeit. Bitte prüfen Sie, ob aufgrund folgender Hinweise die Störung selbst behoben werden kann. Sie vermeiden dadurch die Kosten für einen unnötigen Kundendiensteinsatz. Im Normalbetrieb leuchtet die LED „Anode“ konstant, die LED „Service" ist aus. Blinkt eine der beiden LEDs, zeigt das einen „Fehlerzustand“ an. In Fehlerfall das Gerät nicht von der Stromversorgung trennen.
Anzeigelampe (LED) Status Anode ein ein Service Stark Heizung blinken blinken aus aus Wärmeinhaltsanzeige Lampen (LED) Ursache / Fehler Behebung Wer 1 2 3 4 5 6 siehe Elektronik ist intern gesperrt, 15 Minuten warten, ein ein unten - ein ein Interner Eletronikfehler dann Reset starten (*) ein - ein - siehe unten (*) siehe unten (*) - Der Speicher hat ohne - ein Wasserfüllung aufgeheizt Warmwasser- ein - Temperatur im Speicher zu hoch Schalten Sie das Gerät aus.
Für Benutzer und Fachmann Gebrauchsanleitung Bevor Sie das Gerät benutzen, lesen Sie bitte sorgfaltig diese Gebrauchsanleitung! Sicherheitshinweise • Dieses Gerät ist für den Haushalt oder für haushaltsähnliche, nicht-gewerbliche Anwendungen bestimmt. Haushaltsähnliche Anwendungen umfassen z. B. die Verwendung in Mitarbeiterküchen von Läden, Büros, landwirtschaftlichen und anderen gewerblichen Betrieben, sowie die Nutzung durch Gäste von Pensionen, kleinen Hotels und ähnlichen Wohneinrichtungen.
Ihr neues Gerät Die Warmwasser Wandspeicher DG80025 – DG15025 mit elektronischer Regelung sind für die Erwärmung von Trinkwasser nach DIN 1988 vorgesehen. Sie können bedarfsgerecht Warmwasser bis 85°C bereitstellen und je nach Betriebsweise eine oder mehrere Zapfstellen (Entnahmestellen) versorgen. Das Wasser wird elektrisch aufgeheizt. Auf der Bedienblende wird die aktuell verfügbare Warmwassermenge durch 6 LEDs angezeigt.
LED Anzeige Anode und Service Im Normalbetrieb leuchtet die LED „Anode“ konstant, die LED „Service" ist aus. Blinkt eine der beiden LEDs, zeigt das einen „Fehlerzustand“ an. Bitte zuerst das Gerät zurücksetzen ➜ RESET, dazu wie folgt vorgehen: Zuerst den Drehknopf auf die Stellung ” ” drehen Anschließend die Schnellheiztaste drücken. Wenn die Ursache des „Fehlerzustands“ unmittelbar nach dem Zurücksetzen nicht mehr besteht, setzt das Gerät wieder seine normale Betriebs-Funktion fort.
en General warnings • This manual is an integral and essential part of the appliance. It should be preserved with care alongside the appliance even if the latter is transferred to another owner or user and/or moved to another location. • Carefully read the instructions and warnings contained in this manual; they provide important information for the safe installation, use and maintenance of your new appliance.
(de-presurised) operation. Closed (pressurised) operation appropriate safety valve combinations, or rather, safety valve combinations with a pressure reducing valve, are to be installed.See assembly preparations (page I). In closed operation, the pressure relief valve must actuated regularly to check its function and to remove limescale deposits (fig. 2): Turn venting screw until a jet of water is expelled. Close the venting screw again. If the safety valve is not working, contact the after-sales service.
Water Connection (page III / IV, diagrams 10 to 12) Only detachable connections are permissible! Before connecting the fittings, thoroughly flush out the water pipes in order to remove any impurities. For closed operations, if the safety valve is not directly above the drain, then the drain pipe must be mounted at a continuous downward slope in a frost-free environment. Please take care because of application range within water types according to technical data on page 17.
Mode of Operation Power Switch “S1” Double power switch positions 5 / 6 / 7 Single power switch positions 1/ 2 / 3 / 4 Boiler mode switch positions 8 / 9 / 0 The power switch is set by the manufacturer in position 5 for DG80025 and DG10025 models and in position 6 for DG12025 and DG15025.
Initial Use Important! Fill the reservoir and flush it out until water discharges from all hot water taps, otherwise the temperature sensor and retainer will be damaged and require replacing. During heating, displaced water must drop from the discharge of the safety valve (closed operation) or out of the mixer tap (open operation). Monitor the first heating cycle. Temperature Limits (page I, diagrams 2 to 4) 1. Set temperature selector to position ” • ” and remove. 2.
Technical Data DG80025 DG10025 DG12025 DG15025 Litres 80 100 120 150 kg 106 133 162 197 Model Volume Weight when full Mpa (bar) Maximum operating pressure Heating time in hrs, with cold water intake of ca.
In case of fault If your device does not function as intended, it is usually due to a small detail. Please check whether or not the fault can be self-repaired according to the following indicators. You will thereby avoid the costs of an unnecessary repair service. In normal operations, the LED “anode” is constantly lit, the LED “service” is off. If one of the two LEDs flashes, this indicates an “error condition”. In case of fault, do not disconnect the power supply line.
Display (LED) Status Anode Service Fast Heating On Flashing Off On Flashing Off Heat content display indicators (LED) Cause / Fault 1 2 3 4 5 On On See below (*) - Internal On On electronic failure - See below (*) On - - Solution Who 6 Electronic board locked, wait 15mins and then reset Technician The reservoir Turn the device off, check the cause of the water has heated On without water shortage (leakage, faulty water connection).
For Users and Technicians Instructions for Use Before you use the device, please read this instruction manual carefully! Safety advice • This device is intended for household or household-like use, not for commercial purposes. Household-like applications include, for example, use in staff kitchens of shops, offices, agricultural and other business operations, as well as use by guests in hostels, small hotels and similar living facilities.
Your new device The hot water storage units DG80025 – DG15025 with electronic control are designed for the heating of drinking water according to DIN 1988. They can provide hot water to 85°C and, depending on the mode of operation, service one or more taps (tapping points). The water is heated electrically. On the control panel the current amount of available hot water is displayed by 6 LEDs.
LED display anode and service In normal operations, the LED “anode” is constantly lit, the LED “service” is off. If one of the two LEDs flashes, this indicates an “error condition”. To begin with, please reset the device ➜ RESET. To do this, proceed as follows: Firstly turn the dial to the setting ” ”. After that, press the “fast-heating” button . If the cause of the error condition does not exist directly after the reset, the device will again return to its normal mode of function.
Siemens Info Line (Mo-Fr: 8.00-18.00 Uhr erreichbar) Für Produktinformationen sowie Anwendungs- und Bedienungsfragen: Tel.: 0911 70 440 044 oder unter siemens-info-line@bshg.
42.0.01.04848.