Data Sheet for Product

ManualsBrandsSiemens ManualsFire - DMS8000 Network & TerminalsMT8001 MP3.15 Management Terminal Installation Function & Configuration Commissioning Safety Regulations

Building Technologies

Fire Safety & Security Products

Product Datasheet

DMS

MT8001 MP3.15

Management Terminal

 Centralisation and management of safety and security control systems

 Specialised interface designed for rapid and accurate handling of events in

emergency situations

 Highly reliable wall mountable unit

 User-friendly, intuitive, touch-screen interface

 Ergonomically designed

 Quick and easy to set up

 Windows CE operating system

 Bright 10.4” TFT colour display

 Compliant with local quality assurance standards

Summary of content (8 pages)

PAGE 1
Product Datasheet DMS MT8001 MP3.15 Management Terminal  Centralisation and management of safety and security control systems  Specialised interface designed for rapid and accurate handling of events in emergency situations  Highly reliable wall mountable unit  User-friendly, intuitive, touch-screen interface  Ergonomically designed  Quick and easy to set up  Windows CE operating system  Bright 10.
PAGE 2
System Overview The MT8001 Management Terminal was designed to provide an easy-to-use point of access to part of a security network or to an entire network. Whether the security network is limited to a single floor, or an entire building, the MT8001 allows you to monitor and control any area or device within the system from one place. The MT8001 provides management station functionality in a wall or desk-mountable cabinet.
PAGE 3
The following subsystems are supported via an NK8223:  CS11 AlgoRex (EP5 and EP7F), FC700A, and CZ10 fire detection systems  CS6 Guarto (MP3) intrusion detection systems  CS440 and SI410 Sintony intrusion detection systems  CC60 Gas detection systems  MF7033/MM7033 Mux/Demux systems  STT11 (Système de Télécommande et Télésignalisation)  CF9000 Input/Output systems Multi-discipline connectivity via an NK8223 as a stand-alone system Note: Up to four CS6 Guarto panels are supported Decentralised co
PAGE 4
EN54 The following configuration is currently awaiting approval for fire detection applications by the VdS-Approval Authority (based on the European Standard EN54-2).  See footnote page 5. AlgoRex CC11 via ISO1745 interface protocol. Specialised Operator Interface The MT8001 was designed specifically for safety and security applications and uses a simple and intuitive touch screen interface.
PAGE 5
Event browser (standard GUI pictured) A B C D E Event description - indicates the state of the detector or data point. Event date & time - shows the date and time when the event occurred Action to do - specifies the action you need to perform Note: The action you need to do is only indicated before selecting the event for treatment, and flashes on and off until the event is selected. Event icon - shows the nature of the event (in this case it is fire-related).
PAGE 6
Technical data Operating System Windows CE.Net Hardware Data Display Touch screen Processor RAM Compact Flash Card V24 (RS-232) Serial interface TTY Serial interface 10.4” TFT-Colour-display (640x480 pixels) Impact strength compliant with EN54-2 ETX-mgx, 200 MHz 128 MB DRAM (expandable to 256MB) 64 MB (expandable) 4 (see communication lines for details) 2 Power Supply Input Voltage Power 24 VDC 18.5 V … 31.
PAGE 7
PAGE 8
Siemens Switzerland Ltd Building Technologies Group International Headquarters Fire Safety & Security Products Gubelstrasse 22 CH-6301 Zug Tel +41 41 724 24 24 Fax +41 41 724 35 22 www.sbt.siemens.com Document no. 006952_e_en_-- Edition 09.2005 © 2006 Copyright by Siemens Switzerland Ltd Data and design subject to change without notice. Supply subject to availability.