Product Brochure

Product Specification Sheet #HD30.13 (page 2 of 2)
Compression Lugs (UL listed for field installation)
2
Dimensions and Wire Bending Space
Wire
Burndy Thomas-Betts IIsco
Size CU Only CU/AL CU Only CU/AL CU Only CU/AL
60096
#14-10
60097
YA8C-L BOX 54104 60101 CRA-8 ACL-8
#8 YA8C-L1 BOX 54130 60102 ACN-8
61102
#6 61107
Catalog
Dimensions Wire Bending Space
Number A B C Top Bottom
DTNF221
DTNF321
24.50 19.00 24.98
DTNF361
(622) (483) (634)
4.75 4.75
DTF321 29.14 23.50 29.63 4.75 7.50
DTF361 (740) (597) (753) 4.75 4.75
Dimension Drawing
1
Catalog number is same as switch catalog number plus “DOOR” suffix.
2
If compression lugs are used for the neutral, order compression lug neutral barrier
kit HCL612.
B
2.44
(62)
6.75 (171)
3.375
(86)
C
L
(6) .268"
(6.8) diameter
mounting holes
(4) knockouts in
back and (2) in
each side for 1/2,
3/4 & 1" conduit
1.75 (44)
1.75 (44)
5.73
(146)
C
2.45
(62)
6.09
(155)
.94 (24)
.25(6)
2.06
(52)
16.44
(418)
Note: This
KO only
omitted on
Non-Fusible
Switches
A
(OD Box
Less Cover)
1.13
(29)
2.06
(52)
1.65 (42)
1.65 (42)
2.37
(60)
This mounting
hole omitted
on DTNF221,
DTNF321 &
DTNF361
C
L
11.53
(293)
2.00
(51)
2.00
(51)
(2) knockouts
for 1/2" conduit
(2) 1/2"
knockouts
3.32
(84)
.97
(25)
1.00
(25)
1.00
(25)
9.53
(242)
1.69 (43)
(4) knockouts
for 1/2, 3/4,
1" conduit
Note: Typical of both
top and bottom ends
Accessories
Catalog
Number Description
HA161234 Auxiliary Switch (1-NO & 1 NC)
1
HA261234 Auxiliary Switch (2-NO & 2 NC)
1
HA361234 Low Voltage Auxiliary Switch
1
HG61234 Equipment Ground Lug Kit (two lugs provided)
HG261234 Isolated Equipment Ground Lug Kit
HP61 Fuse Puller (3 per kit, (2) kits required per switch)
HNC612 Neutral Kit
HR21 240 Volt Class R Fuse Clip Kit (3 fuse clips per kit,
(2) kits required per switch)
HR612 600 Volt Class R Fuse Clip Kit (3 fuse clips per kit,
(2) kits required per switch)
HLC612 Copper Lug Kit (9 lugs per kit)
HCL612 Compression Lug Neutral Barrier Kit
Catalog
Number Description
HFB21 Fusible 240 Volt Line Side Replacement Base (2) kits
required per switch
HBB21 Fusible 240 Volt Load Side Replacement Base (2) kits
required per switch
HFB612 Fusible 600 Volt Line Side Replacement Base (2) kits
required per switch
HBB612 Fusible 600 Volt Load Side Replacement Base (2) kits
required per switch
HNB612 Non-fusible Replacement Line Base (2) Kits required per switch
HHD61234 Replacement Handle/Handle Guard
HL612 Replacement Lugs (3 lugs per kit)
HM6123 Replacement Mechanism (2) kits required per switch
1
Replacement Door
Replacement Parts
Dimensions shown in inches and millimeters ( ).
Dimension shown accurate to
+
¹⁄₈ inch.
Enclosure: Cold Rolled Steel .053 Thick (17 Gauge)
Finish – ANSI Grey #61 Paint
Siemens is a registered trademark of Siemens AG. Product names
mentioned may be trademarks or registered trademarks of their
respective copanies. Specifications subject to change without notice.
www.usa.siemens.com/switches
Siemens Industry, Inc.
Building Technologies Division
5400 Triangle Parkway
Norcross, GA 30092
1-800-964-4114
Subject to change without prior notice
All rights reserved
Printed in USA
© 2009 Siemens Industry, Inc.