Data Sheet for Product

ManualsBrandsSiemens ManualsFire - LMS Management StationsENCL-01 Enclosure, Installation Instructions

Siemens

Smart Infrastructure - Building Products

Data Sheet 9301

usa.siemens.com/fire

Cerberus® DMS

XNET Monitoring-Only Solution Assembly

Model MOSA

Architect & Engineer Specifications

 Cost-effective, monitoring-only XNET

interface designed for connecting a

Cerberus DMS to an XNET FIRE

network

 Allows Cerberus DMS to connect to

an XNET fire network from any non-

UL 864 / ULC-S527-11 Listed

computer as an ancillary annunciator

 Transports the XNET protocol over an

Ethernet connection between the

XNET Monitoring-Only Solution

Assembly (MOSA) and the Cerberus

DMS

 Converts the serial-based XNET

connection to an Ethernet

connection between the XNET

Monitoring-Only Solution Assembly

(MOSA) and the Cerberus DMS

 Up to four (4) Model MOSA can

connect to each Cerberus DMS server

or Front-End Processor (FEP)

 XNET Monitoring-Only Solution

Assembly is UL and ULC recognized

as an ancillary annunciator when

used with a non-UL 864 / ULC-S527-

11 Listed PC

Product Overview

The XNET monitoring-only solution assembly (MOSA) is a cost-effective, monitoring-

only XNET interface designed for connecting a Cerberus Danger Management

Station (DMS) to an XNET FIRE network using a non-UL 864 / non-ULC-S527-11

Listed computer as an ancillary annunciator.

The MOSA transports the XNET protocol over an Ethernet connection between a

MOSA and a Cerberus DMS.

The MOSA is UL / ULC recognized as an ancillary annunciator when used with a

non-UL 864 / non-ULC-S527-11 Listed computer. The MOSA can connect to XNET

FIRE networks comprised of the following: Cerberus PRO Modular, FireFinder XLS,

MXL, Network Command Center (NCC), or Hybrid XNET networks that follows the

XNET rules for hybrid networks.

Additionally, the combination of Model MOSA and a non-UL 864 / ULC-S527-11

Listed PC can replace a Model NCC-2F LifeLINK interface card or SNC, as well as a

UL 864 / ULC-S527-11 Listed PC for connecting the Cerberus DMS to an XNET

network for monitoring-only connections.

See: Details for Ordering section on Page 4 for the list of kit components for Model MOSA.

Specifications

Model MOSA connects to the XNET FIRE

network via the monitoring port on Model

NIC-C located in a Cerberus PRO Modular or

FireFinder XLS panel. Connections to NRC

network rings are also supported where

MOSA connects to the NRC network ring via

the NRC / NIC-C bridge. An assembled Model

MOSA must be installed within 20 feet (6.1

meters) – wires in conduit – of the

FireFinder XLS/V panel, providing the NIC-C

interface and 24 Volts DC power source to

the MOSA.

The actual distance is limited to 10 feet (3

meters) due to the length of the NIC-C to

XND-M interface cable. In addition, the

assembled Model MOSA must be installed

within 20 feet (6.1 meters)– wires in

conduit – of the Ethernet switch,

connecting a MOSA to the intranet.

Mounting set-up of a

XNET MOSA

Summary of content (5 pages)

PAGE 1
Cerberus® DMS XNET Monitoring-Only Solution Assembly Model MOSA Architect & Engineer Specifications Product Overview  Cost-effective, monitoring-only XNET interface designed for connecting a Cerberus DMS to an XNET FIRE network The XNET monitoring-only solution assembly (MOSA) is a cost-effective, monitoringonly XNET interface designed for connecting a Cerberus Danger Management Station (DMS) to an XNET FIRE network using a non-UL 864 / non-ULC-S527-11 Listed computer as an ancillary annunciator.
PAGE 2
Specifications (continued) Model MOSA requires a fixed IP address. A total of four (4) XNET MOSAs can connect to each Cerberus DMS server or Front End Processor (FEP). A MOSA enclosure (Model ENCL-01) contains a key-lock that is placed in the center, righthand side, and the door hinge is located on the left-hand side of the enclosure. There are three (3) 1/2” {2.54 cm.} – 3/4” {1.91 cm.} NPT knockouts, two (2) on the right-hand side and one (1) NPT knockout on the left-hand side.
PAGE 3
Intranet Connection + Additional Client(s) Dimensional Drawing The following diagram illustrates the dimensions of a Monitoring-Only Solution Assembly enclosure, Model ENCL-01 (All dimensions in inches ) Technical Data Electrical Ratings 24V BACK PLANE CURRENT: Physical Properties 0 SCREW TERMINAL, 24V CURRENT: 26mA 6.2V BACK PLANE CURRENT: 0 24V STANDBY CURRENT: 26mA DIMENSIONS ( W –x– H –x– D ) WEIGHT Siemens Smart Infrastructure - Building Products –3– 8.5’’ –x– 13.3’’ –x– 2.75’’ (21.
PAGE 4
Details for Ordering MODEL OR TYPE PART NUMBER PRODUCT Each order of Model MOSA consists of the following components: S54465-C62-A1 MOSA ▪ One (1) Model ENCL-01 enclosure with key-lock door ▪ One (1) Model S2E: Serial-toEthernet Module ▪ One (1) Model XND-M: XND-M (XNET interface) Module for MOSA ▪ One (1) Model PS-5A: Auxiliary 5V power supply module ▪ One (1) Model BRKT-M: Bracket for mounting an XND-M module to a Model ENCL-01 enclosure ▪ One (1) Model CBL-M: MOSA Cables Two (2) S2E power cable
PAGE 5
NOTICE – The information contained in this data-sheet document is intended only as a summary, and is subject to change without notice. The product(s) described here has/have a specific instruction sheet(s) that cover various technical, limitation and liability information. Copies of install-type, instruction sheets – as well as the General Product Warning and Limitations document, which also contains important data, are provided with the product. All are available from the Manufacturer.