4 © Siemens AG 2014 AS-Interface 4/2 4/2 4/3 4/4 Introduction Communication overview System components AS-Interface specification V3.0 4/6 4/6 4/48 4/40 Ch.
© Siemens AG 2014 AS-Interface Introduction Communication overview ■ Overview AS-Interface is a single master system. For automation systems from Siemens, there are communications processors (CPs) communications modules (CMs) and network transitions (links) that control the process or field communication as masters, and actuators and sensors that are activated as AS-Interface slaves. AS-Interface is an open, international standard according to EN 50295 and IEC 62026-2 for process and field communication.
© Siemens AG 2014 AS-Interface Introduction System components ■ Overview To implement communication, a system installation has the following main components: • Master interface modules for central control units such as SIMATIC S7, ET 200/ET 200SP distributed peripherals, or network transitions from PROFIBUS/PROFINET to AS-Interface • Power supply units, if required in combination with a data decoupling module for the power supply to the slaves • AS-Interface shaped cables • Network components such as rep
© Siemens AG 2014 AS-Interface Introduction AS-Interface specification Specification V3.0 ■ Overview ■ More information Scope of the AS-Interface specification AS-Interface system manual Maximum number of slaves Number of digital inputs Number of digital outputs Digital Analog ASIsafe DI DO 62 62 31 62 8 = 496 62 8 = 496 Basic data 4 AS-Interface Specification 3.0 describes a fieldbus system with an AS-i master and up to 62 AS-i slaves.
© Siemens AG 2014 AS-Interface Introduction AS-Interface specification AS-i Power24V expansion ■ Overview AS-Interface data decoupling modules for AS-i Power24V, left: S22.5 data decoupling module, right: DCM 1271 data decoupling module for SIMATIC S7-1200 Parallel wiring frequently dominates, above all, in applications with very few I/Os.
© Siemens AG 2014 AS-Interface ASIsafe Introduction ■ Overview ASIsafe – Safety is included Configuring safety functions ASIsafe enables the integration of safety-related components, such as EMERGENCY-STOP pushbuttons, protective door switches or safety light arrays, in an AS-Interface network. These are fully compatible with the familiar AS-Interface components (masters, slaves, power supplies, repeaters, etc.
© Siemens AG 2014 AS-Interface ASIsafe Introduction ■ Overview (continued) AS-i safety solution with local evaluation by MSS Operational control Controls e. g.
© Siemens AG 2014 AS-Interface ASIsafe AS-Interface safety monitors ■ Selection and ordering data Version Article No.
© Siemens AG 2014 AS-Interface ASIsafe AS-Interface safety modules ■ Overview K45F compact safety modules for use in the field AS-Interface safety modules: K45F (left), K20F (center) and S22.5F (right) The platform of the K45F modules covers the following variations: • Connection of ("mechanical") switches/safety sensors with contacts: - K45F 2F-DI: Two safety-related inputs in operation up to Category 2 according to EN ISO 13849-1.
© Siemens AG 2014 AS-Interface ASIsafe AS-Interface safety modules ■ Selection and ordering data Version Article No.
© Siemens AG 2014 AS-Interface ASIsafe AS-Interface safety modules ■ Accessories Version Article No. K45 mounting plates For mounting K45F • For wall mounting 3RK1901-2EA00 • For standard rail mounting 3RK1901-2DA00 24 V supply modules for K45F LS (light sensor) 3RK1901-1NP00 3RK1901-2EA00 • Optional, for transmitter power supply for large protective field widths • Max.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches ■ Overview The 3SF1 position switches with safety-related communication can be directly connected using the AS-Interface bus system. The safety functions no longer have to be conventionally wired up. With the 3SF1 position switches the ASIsafe electronics component is integrated in the switch enclosure.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches Plastic enclosures ■ Selection and ordering data Modular system For the ASIsafe version of the position switch, the basic switch and actuator must be ordered separately. 1 or 2 contacts · 3 LEDs · Degree of protection IP65 (31 mm) or IP66/IP67 (50 mm) · M12 connector socket Version Contacts LEDs Article No. Basic switches (with rounded plunger1)) · Enclosure width 31 mm acc.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches Plastic enclosures ■ Selection and ordering data (continued) Version Diameter Article No. mm Operating mechanisms Roller plungers, type C acc.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches Metal enclosures ■ Selection and ordering data Modular system For the ASIsafe version of the position switch, the basic switch and actuator must be ordered separately. 2 contacts · 3 LEDs · Degree of protection IP66/IP67 · M12 connector socket Version Contacts LEDs Article No. Basic switches (with rounded plunger1)) · Enclosure width 31 mm acc.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches Metal enclosures ■ Selection and ordering data (continued) Version Diameter Article No.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches Metal enclosures ■ Selection and ordering data (continued) Modular system For the ASIsafe version of the position switch, the basic switch and actuator must be ordered separately. 1 or 2 contacts · 3 LEDs · Degree of protection IP66/IP67 · M12 connector socket Version Contacts LED • Slow-action contacts 2 NC 24 V DC q 3SF1114-1KA00-1BA1 • Snap-action contacts 2 NC 24 V DC q 3SF1114-1LA00-1BA1 Article No.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches Metal enclosures ■ Selection and ordering data (continued) Version Diameter Article No.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches with separate actuator ■ Overview The 3SF1 safety switches with safety-related communication can be directly connected using the AS-Interface bus system. The safety functions no longer have to be conventionally wired up. With the 3SF1 safety switches the ASIsafe electronics component is integrated in the switch enclosure.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches with separate actuator Plastic enclosures ■ Overview • Contacts: 1 or 2 slow-action contacts • Status display with 3 LEDs 24 V DC; 1: F–IN1, 2: F–IN2, 3: AS-i/FAULT • Degree of protection IP65 (31 mm) or IP66/IP67 (50 mm) ■ Selection and ordering data Version1) Contacts Article No. Enclosure width 31 mm acc.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches with separate actuator Metal enclosures ■ Overview • Contacts: 1 or 2 slow-action contacts • Status display with 3 LEDs 24 V DC; 1: F–IN1, 2: F–IN2, 3: AS-i/FAULT • Degree of protection IP66/IP67 ■ Selection and ordering data Version1) Contacts Article No. Enclosure width 31 mm acc.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches with separate actuator Accessories ■ Selection and ordering data Version Article No. Actuators Standard actuators 4 Standard actuators, length 75.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches with solenoid interlocking ■ Overview The 3SF1 safety switches with safety-related communication can be directly connected using the AS-Interface bus system. The safety functions no longer have to be conventionally wired up. With the 3SF1 safety switches the ASIsafe electronics component is integrated in the switch enclosure.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches with solenoid interlocking Plastic housings ■ Overview 4 5 directions of approach · Degree of protection IP66/IP67 • Slow-action contacts: - Version -1BA1: ASIsafe channel 1 on 1 NC contact from the actuator and channel 2 on 1 NC contact from the solenoid - Version -1BA3: ASIsafe channel 1 on the first NC contact from the actuator and channel 2 on the second NC contact from the actuator - Version -1BA4: ASIsafe channel 1 on 2 NC cont
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches with solenoid interlocking Metal housings ■ Overview 5 directions of approach · Degree of protection IP66/IP67 • Slow-action contacts: Version -1BA1: ASIsafe channel 1 on 1 NC contact from the actuator and channel 2 on 1 NC contact from the solenoid • Solenoid: Rated operational voltage 24 V DC • 2 600 N locking force • Status display with 4 LEDs 24 V DC; 1: AS-i, 2: FAULT, 3: F–IN1, 4: F–IN2 Safety level Version Contacts Achievable
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches Hinge switches – plastic enclosures ■ Overview The 3SF1 safety hinge switches with safety-related communication can be directly connected using the AS-Interface bus system. The safety functions no longer have to be conventionally wired up. For the ASIsafe version of the hinge switch, the basic switch and actuator head must be ordered separately.
© Siemens AG 2014 AS-Interface ASIsafe 3SF1 mechanical safety switches Hinge switches – metal enclosures ■ Overview The 3SF1 safety hinge switches with safety-related communication can be directly connected using the AS-Interface bus system. The safety functions no longer have to be conventionally wired up. For the ASIsafe version of the hinge switch, the basic switch and actuator head must be ordered separately.
© Siemens AG 2014 AS-Interface ASIsafe 3SF2 cable-operated switches for AS-Interface ■ Overview SIRIUS cable-operated switches are used for monitoring or for EMERGENCY-STOP devices on particularly endangered system components. AS-Interface cable-operated switches can be directly connected via the bus system AS-Interface with safety-related communication. The safety functions no longer have to be conventionally wired up.
© Siemens AG 2014 AS-Interface ASIsafe SIRIUS EMERGENCY-STOP mushroom pushbuttons for AS-Interface ■ Overview EMERGENCY- STOP devices can be directly connected via the standard AS-Interface with safety-related communication. This applies only to series SIRIUS 3SB3 EMERGENCY-STOP mushroom pushbuttons for front panel mounting and installation in an enclosure. AS-Interface EMERGENCY-STOP enclosure The enclosure is supplied fully equipped and wired.
© Siemens AG 2014 AS-Interface ASIsafe SIRIUS EMERGENCY-STOP mushroom pushbuttons for AS-Interface ■ Selection and ordering data EMERGENCY-STOP devices acc. to ISO 13850 and IEC 60947-5-5 • With holder for front plate mounting • Connection with AS-Interface F adapter • Yellow contrast surfaces must be ordered separately. Version Approval Article No.
© Siemens AG 2014 AS-Interface ASIsafe SIRIUS EMERGENCY-STOP mushroom pushbuttons for AS-Interface ■ Selection and ordering data (continued) EMERGENCY-STOP devices acc. to ISO 13850 and IEC 60947-5-5 • With holder for front plate mounting • Connection with AS-Interface F adapter • Yellow contrast surfaces must be ordered separately. Version Approval Article No.
© Siemens AG 2014 AS-Interface ASIsafe AS-Interface F adapters for EMERGENCY-STOP devices ■ Overview The AS-Interface F adapter is used to connect an EMERGENCYSTOP device according to ISO 13850 from the 3SB3 series to the AS-Interface bus system. The F adapter is suitable for control devices with mounting on front plates. The F adapter has a safe AS-Interface 2I slave and is snapped from behind onto the EMERGENCY-STOP mushroom pushbutton.
© Siemens AG 2014 AS-Interface Masters Masters for SIMATIC S7 CM 1243-2 ■ Overview Function The CM 1243-2 supports all specified functions of the AS-Interface Specification V3.0. The values of the digital AS-i slaves can be activated via the process image of the S7-1200. During configuration of the slaves in the TIA Portal, the values of the analog AS-i slaves can also be accessed directly in the process image.
© Siemens AG 2014 AS-Interface Masters Masters for SIMATIC S7 CM 1243-2 ■ Benefits • More flexibility and versatility in the use of SIMATIC S7-1200 as the result of a significant increase in the number of digital and analog inputs/outputs available • Very easy configuration and diagnostics of the AS-Interface via the TIA Portal (STEP 7 V11+ SP2 or higher) • No need for the AS-i power supply unit with AS-i Power24V: The AS-Interface cable is supplied through an existing 24 V DC PELV power supply unit.
© Siemens AG 2014 AS-Interface Masters Masters for SIMATIC S7 CP 343-2P / CP 343-2 ■ Overview Design The CP 343-2P / CP 343-2 is connected like an I/O module to the S7-300.
© Siemens AG 2014 AS-Interface Masters Masters for SIMATIC S7 CP 343-2P / CP 343-2 ■ Application The CP 343-2P / CP 343-2 is the AS-Interface master connection for the SIMATIC S7-300 and the ET 200M. Through connection to AS-Interface it is possible to access max. 248 DI/248 DO per CP, using 62 A/B slaves with 4DI/4DO each.
© Siemens AG 2014 AS-Interface Masters Masters for SIMATIC ET 200 CM AS-i Master ST for SIMATIC ET 200SP ■ Overview Function The CM AS-i Master ST supports all specified functions of the AS-Interface Specification V3.0. The input/output values of the digital AS-i slaves can be activated via the cyclic process image. The values of the analog AS-i slaves can be reached via data record transfer. If required, master calls can be performed with the command interface, e.g.
© Siemens AG 2014 AS-Interface Masters Masters for SIMATIC ET 200 CM AS-i Master ST for SIMATIC ET 200SP ■ Benefits The CM AS-i Master ST for ET 200SP communication module enables modular, easy and high-performance expansion of AS-Interface networks via engineering in the TIA Portal. Up to eight CM AS-i Master ST units can be plugged into one ET 200SP station with IM 155-6 PN Standard. The maximum configuration depends on the interface module used.
© Siemens AG 2014 AS-Interface Masters Masters for SIMATIC ET 200 CM AS-i Master ST for SIMATIC ET 200SP ■ Accessories (continued) Version Article No. PROFINET interface modules IM 155-6 PN Standard Max. 32 I/O modules, max.
© Siemens AG 2014 AS-Interface Masters Masters for SIMATIC ET 200 F-CM AS-i Safety ST for SIMATIC ET 200SP ■ Overview • Informative front-side module inscription - Plain-text marking of the module type and function class - 2D matrix code (article number and serial number) - Circuit diagram - Color coding of the CM module type: Light gray - Hardware and firmware version - Complete article number • Optional labeling accessories - Labeling strips - Reference identification label Design The fail-safe F-CM AS-
© Siemens AG 2014 AS-Interface Masters Masters for SIMATIC ET 200 F-CM AS-i Safety ST for SIMATIC ET 200SP ■ Overview (continued) Supported BaseUnits Configuration With the recommended combination of the CM AS-i Master ST and F-CM AS-i Safety ST modules, the CM module is plugged onto a light type C0 BaseUnit and, directly on the right of it, the F-CM module is plugged onto a dark type C1 BaseUnit. The AS-i cable is connected only on the light BaseUnit of the CM module.
© Siemens AG 2014 AS-Interface Masters Masters for SIMATIC ET 200 F-CM AS-i Safety ST for SIMATIC ET 200SP ■ Selection and ordering data Version Article No. F-CM AS-i Safety ST communication modules 3RK7136-6SC00-0BC1 • Fail-safe module for SIMATIC ET 200SP, can be plugged onto BaseUnit type C1 (alternatively type C0) • An AS-i master, e.g.
© Siemens AG 2014 AS-Interface Network transitions DP/AS-i LINK Advanced ■ Overview Functionality DP/AS-i LINK Advanced '3 0 '3 6 $6L 0 ,. B 31 The DP/AS-i LINK Advanced is a compact network transition between PROFIBUS (DP Slave) and AS-Interface, with the following features: • Single and double AS-Interface master (according to AS-Interface Specification V3.
© Siemens AG 2014 AS-Interface Network transitions DP/AS-i LINK Advanced ■ Benefits • Short startup times through simple configuration at the press of a button and testing of the AS-Interface line using the display or web interface • Reduction of standstill and servicing times in the event of a slave failure thanks to user-friendly diagnostics using the display or web interface and through simple module exchange with the help of the C-PLUG exchange medium • Reduced amount of engineering work thanks to use
© Siemens AG 2014 AS-Interface Network transitions DP/AS-i LINK Advanced ■ Selection and ordering data Version Combicon connection Article No. DP/AS-i LINK Advanced DP/AS-i LINK Advanced Network transition between PROFIBUS DP and AS-Interface; degree of protection IP20; including COMBICON plug-in screw terminals for connection of an AS-Interface cable (two AS-Interface cables for double masters) and the optional 24 V supply; corresponds to AS-Interface Specification 3.
© Siemens AG 2014 AS-Interface Network transitions DP/AS-Interface Link 20E ■ Overview Design • Compact plastic enclosure in degree of protection IP20 for standard rail mounting • LEDs in the front panel for indicating the operating state and functional readiness of all connected slaves • Setting of PROFIBUS DP address is possible by pressing a button • LED indication of the PROFIBUS DP slave address, DP bus faults and diagnostics • Two pushbuttons for switching over the operating state and for adopting t
© Siemens AG 2014 AS-Interface Network transitions DP/AS-Interface Link 20E ■ Application (continued) PC/IPC with CP 5621 S7-400 E.g.
© Siemens AG 2014 AS-Interface Network transitions DP/AS-i F-Link ■ Overview Design • Rugged, slim plastic enclosure, degree of protection IP20, for standard mounting rail or wall mounting (with adapter) • Compact design: - LEDs in the front panel for indicating the operating state and functional readiness of all connected slaves - 2 buttons on the front for start-up and call-up of diagnostics information - 4 LEDs for display of the operating state of the device, of PROFIBUS DP and the AS-Interface networ
© Siemens AG 2014 AS-Interface Network transitions DP/AS-i F-Link ■ Benefits • Gaps in (bus-based) safety technology closed: safety-related signals (EMERGENCY-STOP, door interlock, light curtains etc.) collected with AS-i and transferred to higher-level F-PLC. This enables: - Quick installation, easy commissioning: benefits of AS-i can now be systematically leveraged in the field for Safety Integrated.
© Siemens AG 2014 AS-Interface Network transitions DP/AS-i F-Link ■ Application (continued) Network connectivity The DP/AS-i F-Link can be used in PROFIBUS and PROFINET networks as follows: HMI SIMATIC S7-300F PROFIBUS F-DI AI/AO DI/DO SIMATIC ET 200S DP/AS-i F-Link (Spec. V3.
© Siemens AG 2014 AS-Interface Network transitions DP/AS-i F-Link ■ Application (continued) Further network connectivity options • Integration in PROFINET networks under SIMATIC F PLC through IE/PB Link • Integration in SINUMERIK Power Line and Solution Line • Integration under non-Siemens fail-safe control systems using PROFIBUS GSD file, see http://support.automation.siemens.com/WW/view/en/113250 ■ Selection and ordering data Version Article No.
© Siemens AG 2014 AS-Interface Network transitions IE/AS-i LINK PN IO ■ Overview Functionality Communications 4 IE/AS-i LINK PN IO '3 0 '3 6 $6L 0 *B,. B;;B 31 The IE/AS-i LINK PN IO is a compact network transition between PROFINET/Industrial Ethernet (PROFINET IO Device) and AS-Interface, with the following features: • Single and double AS-Interface master (according to AS-Interface Specification V3.
© Siemens AG 2014 AS-Interface Network transitions IE/AS-i LINK PN IO ■ Benefits ■ Application • Short startup times through simple configuration at the press of a button and testing of the AS-Interface line using the display or web interface • Reduction of standstill and servicing times in the event of a slave failure thanks to user-friendly diagnostics using the display or web interface • Costs saved by the double AS-Interface master when large volumes of project data are involved • Saves the need for
© Siemens AG 2014 AS-Interface Network transitions IE/AS-i LINK PN IO ■ Application (continued) Wireless communication Sample uses are applications which up to now have been performed with fault-prone tow chain or collector wire technology. Maintenance costs are thus reduced. Using an upstream IWLAN client module, e.g. SCALANCE W748-1 RJ45, an AS-Interface line can be integrated in the PROFINET world by wireless means.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Digital I/O modules IP67 – Introduction ■ Overview 4 K60 K20 Three coordinated series of AS-Interface compact modules with digital and analog compact modules and a high degree of protection are available for use in the field: • Series K60 (digital and analog) • Series K45 (digital) • Series K20 (digital) All compact modules are characterized by particularly simple handling.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Digital I/O modules IP67 – K60 ■ Overview The K60 digital AS-Interface compact modules are characterized by optimized handling characteristics and user-friendliness. They permit the mounting times and startup times of AS-Interface to be reduced by up to 40 %.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Digital I/O modules IP67 – K60 ■ Selection and ordering data Version Article No.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Digital I/O modules IP68/IP69K – K60R ■ Overview Connection NSA0_00339e Operation in particularly harsh environments K60R IP68 K60R IP68 K60R IP68 4 Distributor 3RK1901-1TR00 K60R module in degree of protection IP68/IP69K Modules with degree of protection IP67 cannot be used in areas exposed to permanently high levels of humidity, in applications with drilling emulsions and cutting oils or when clean
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Digital I/O modules IP68/IP69K – K60R ■ Overview (continued) To simulate requirements as realistically as possible, the modules were artificially aged prior to the tests by 15 temperature cycles of -25/+85 °C. During the test, the modules were connected to 3RX1 connecting cables. Unassigned connections were closed with 3RK1901-1KA00 sealing caps.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Digital I/O modules IP67 – K45 ■ Overview Addressing and connection of the sensors/actuators Addressing of the K45 compact modules is performed using an addressing socket integrated in the module. The addresses can be assigned even when mounted.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Digital I/O modules IP67 – K45 ■ Selection and ordering data Version Article No.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Digital I/O modules, IP67 – K20 ■ Overview The flexibility of the round cable means that it can also be used on moving machine parts without any problems. The K20 modules are also ideal for such applications as their non-encapsulated design makes them particularly light in weight. In applications with tow chains, many users rely on placing the AS-Interface bus cable in a round cable.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Digital I/O modules, IP67 – K20 ■ Selection and ordering data (continued) Version Article No.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Analog I/O modules IP67 – K60 ■ Overview ■ Benefits • Analog modules are just as easy to integrate in AS-Interface as digital modules • Analog values can be easily detected and issued locally • Preprocessing of the analog value transmission in the master enables rapid evaluation of the analog values • Up to four values can be detected using one analog module • Faster transmission and conversion of analog val
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Analog I/O modules IP67 – K60 ■ Selection and ordering data Version Article No. Analog I/O modules IP67 - K60, analog profile 7.3 • Slave type: Standard • Width 60 mm • Modules supplied without mounting plate Inputs Type Measuring range 1 or 2 inputs Current (selectable using jumper plug at socket 3) 4 ... 20 mA or 20 mA (selectable)1) 3RK1207-1BQ40-0AA3 Voltage 10 V or 1 ...
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the field, high degree of protection Analog I/O modules IP67 – K60 ■ Selection and ordering data (continued) Version Article No. Manual "AS-Interface Analog Modules K60" See Accessories http://support.automation.siemens.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the control cabinet Introduction ■ Overview 4 SlimLine S22.5/S45 Flat module For AS-Interface applications inside control cabinets, there are various module series for the most diverse requirements: • SlimLine S22.5 • SlimLine S45 • F90 module1) • Flat module All modules of these series can be snap-mounted directly on a standard mounting rail or be fastened using screws.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the control cabinet SlimLine ■ Overview SlimLine modules of the S22.5 and S45 series An addressing socket integrated at the front enables the module to be addressed also when it is installed. In addition to the digital input/output modules, there are modules of design S22.5 with special functions.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the control cabinet SlimLine ■ Selection and ordering data Version Article No. SlimLine S22.5 modules • Inputs: PNP transistor • Width 22.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the control cabinet F90 Module ■ Selection and ordering data Version Article No.
© Siemens AG 2014 AS-Interface Slaves I/O modules for use in the control cabinet Flat module ■ Overview The flat module for the control cabinet in degree of protection IP20 has 4 inputs and 4 outputs. The module is fitted at the front with an LED which indicates the module's status. With the integrated lugs, the modules can be screwed on. An integrated addressing socket enables the module to be addressed when it is installed.
© Siemens AG 2014 AS-Interface Slaves Special integrated solutions AS-interface communication modules ■ Overview AS-Interface communication modules for printed circuit board installation 3RK1400-0CD01-0AA3 AS-Interface communication modules for printed circuit board installation aux NC + E1 A1 0 E2 A2 0 E3 A3 0 E4 A4 0 + 4 ASIASI+ NSA0_00079a AS-Interface communication module 3RK1400-0CD00-0AA3 (left), AS-Interface communication module 3RK2400-1FD00-0AA2 (right) 3RK1400-0CD00-0AA3 AS-Interface comm
© Siemens AG 2014 AS-Interface Slaves Special integrated solutions AS-interface communication modules ■ Overview (continued) 3RK1400-1CD00-0AA2, 3RK2400-1FD00-0AA2 AS-Interface communication modules for printed circuit board installation 3RK1200-0CD00-0AA2 AS-Interface communication modules for printed circuit board installation Connection Connection pad Connection Connection pad AS-i + 27, 29 AS-i + 27, 29 AS-i - 28, 30 AS-i - 28, 30 Sensor+ 17, 18, 23, 24 Sensor+ 17, 18, 23, 24 Sensor-
© Siemens AG 2014 AS-Interface Slaves Modules with special functions Counter modules ■ Overview U IN1 NSA0_00084 ≥ 300 s t ≥ 1 ms Maximum frequency for the counter module If the time criterion stipulated in the figure is violated, the count value is rejected. The counter is active only for the reset parameter P2 (default). The counter is deleted when P2 is set, and the incoming count pulses are not registered until after P2 is reset again.
© Siemens AG 2014 AS-Interface Slaves Modules with special functions Ground-fault detection modules ■ Overview "Ground faults in any control circuit must not lead to unintentional starting or potentially hazardous movements or prevent the machine from stopping." (IEC 60204-1/VDE 0113-1). The AS-Interface ground-fault detection module is used to meet these requirements. Using this module from the SlimLine series, ground faults in AS-Interface systems can be reliably detected and reported.
© Siemens AG 2014 AS-Interface Slaves Modules with special functions Overvoltage protection modules ■ Overview With the AS-Interface overvoltage protection module, it is now also possible to integrate AS-Interface in the overall overvoltage protection concept of a plant or machine. The module has the same design and degree of protection (IP67) as the AS-Interface K45 compact modules. It is a passive module without AS-i IC and as such does not need its own address on the AS-Interface network.
© Siemens AG 2014 AS-Interface Slaves AS-Interface connections for LOGO! ■ Overview Every LOGO! can now be connected to the AS-Interface system Using the AS-Interface connection for LOGO!, an intelligent slave can be integrated in the AS-Interface system. With the modular interface it becomes possible to integrate the different basic units in the system according to their functionality. Similarly, functionalities can be quickly and easily adapted to new requirements by exchanging the basic unit.
© Siemens AG 2014 AS-Interface Slaves Contactors and contactor assemblies Power contactors for switching motors > SIRIUS 3RT20 contactors ■ Overview Contactors with communication interface, sizes S00 and S0 Contactor versions with communication interface are required to establish a connection to the control system via IO-Link or AS-Interface. The link is established by means of function modules mounted on the front of the contactor.
© Siemens AG 2014 AS-Interface Slaves Contactors and contactor assemblies Contactor assemblies > SIRIUS 3RA24 wye-delta assemblies ■ Overview These 3RA24 contactor assemblies for wye-delta starting are designed for standard applications. Note: Contactor assemblies for wye-delta starting in special applications such as very heavy starting or wye-delta starting of special motors must be customized. Help with designing such special applications is available from Technical Assistance.
© Siemens AG 2014 AS-Interface Slaves Contactors and contactor assemblies SIRIUS 3RA27 function modules for AS-Interface ■ Overview The function modules for mounting onto contactors enable the configuration of starters and contactor assemblies for direct-online, reversing and wye-delta starting without any additional, complicated wiring of the individual components. Manuals For more information see manual "SIRIUS Function Modules for AS-Interface", http://support.automation.siemens.
© Siemens AG 2014 AS-Interface Slaves Contactors and contactor assemblies SIRIUS 3RA27 function modules for AS-Interface ■ Selection and ordering data (continued) Version Screw terminals Spring-type terminals Article No. Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > General data ■ Overview 3RA6 fuseless compact starters and infeed system for 3RA6 Communications integration using IO-Link SIRIUS 3RA64, 3RA65 compact starters for IO-Link see Chapter 5: "IO-Link". Permanent wiring/easy replacement Using the SIRIUS infeed system for 3RA6 it is possible to carry out the wiring in advance without a compact starter needing to be connected.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > General data ■ Overview (continued) The SIRIUS compact starters are generally designed to degree of protection IP20. The permissible ambient temperature during operation is -20 to +60 °C. Type of infeed Infeed terminal Type (acc.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > General data ■ Overview (continued) More components of the 3RA6 Apart from the control supply voltage, "Overload" (1 CO) and "Short circuit / Function fault" (1 NO) signaling contacts are already integrated into the 3RA61/3RA62 – and lockable via two 6-pole removable control circuit terminals. The 3RA61 has two auxiliary contacts (1 NO + 1 NC) for displaying the position of the main contacts.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > 3RA61 direct-on-line starters ■ Selection and ordering data Direct-on-line start Width 45 mm Rated short-circuit current ICS = 53 kA at 400 V A set of 3RA69 40-0A adapters is required for screw fixing. NSB0_01946 3RA61 20-1CB32 3RA61 20-2EB32 Standard three-phase motor 4-pole at 400 V AC1) Setting range for solid-state overload release Instantaneous overcurrent release Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > 3RA62 reversing starters ■ Selection and ordering data Width 90 mm Reversing duty Rated short-circuit current ICS = 53 kA at 400 V Two sets of 3RA69 40-0A adapters are required for screw fixing. NSB0_01947 3RA62 50-1CP32 3RA62 50-2DP32 Standard three-phase motor 4-pole at 400 V AC1) Setting range for solidstate overload release Instantaneous overcurrent release A A Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Accessories ■ Overview Accessories for SIRIUS 3RA6 compact starters Busbar adapters for 60 mm systems The following accessories are available specially for the 3RA6 compact starters: • AS-i add-on module: see page 4/92 onwards "AS-interface add-on modules" • External auxiliary switch blocks: Snap-on auxiliary switch as versions 2 NO, 2 NC and 1 NO + 1 NC with screw or springtype terminals;
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Accessories ■ Selection and ordering data Version Article No. Accessories specially for 3RA6 compact starters Control kit 3RA6950-0A For mechanical actuation of the compact starter 3RA6950-0A Adapters for screw fixing the compact starter (set including push-in lugs) 3RA6940-0A Direct-on-line starters require one set, reversing starters two sets.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Accessories ■ Selection and ordering data (continued) Version Article No. Accessories specially for 3RA6 compact starters (continued) Main circuit terminals mixed connection method 3RA6920-3A 1 set comprises: • 1 joint block on the line side with screw terminals • 1 joint block on the outgoing side with spring-type terminals 3RA6920-3A Version Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Accessories ■ Selection and ordering data (continued) Conductor cross-section Solid or stranded Finely stranded with end sleeve AWG cables, solid or stranded Tightening torque For compact starters and motor starter protectors mm² AWG Nm Size 10-4 4 S0 3RV1925-5AB 10-4 Input: 4; Output: 2 ... 2.5 S00, S0 3RV2915-5B S0 3RV2925-5EB mm² Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Accessories ■ Selection and ordering data (continued) Version Article No. Tools for opening spring-type terminals 3RA2908-1A Screwdrivers For all SIRIUS devices with spring-type terminals Spring-type terminals Length approx. 200 mm, 3.0 mm x 0.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Add-on modules for AS-Interface ■ Overview The AS-i add-on modules can be combined only in connection with compact starters with a rated control supply voltage of 24 V AC/DC. 3RA6120-..B3. D1 AS-i Y4 Y2 AUX PWR - Opening the two inputs Y2 and Y4 will result in the direct disconnection of the compact starter.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Add-on modules for AS-Interface ■ Selection and ordering data Version Article No. Standard version 3RA6970-3A AS-i add-on modules For communication of the compact starter with the control system using AS-Interface With two local inputs 3RA6970-3B For safe disconnection through local safety relays, e.g.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Infeed system for 3RA6 ■ Overview In addition, the integrated PE bar means it is optionally possible to connect the motor cable directly to the infeed system without additional intermediate terminals. The infeed system for 3RA6 compact starters is designed for summation currents up to 100 A with a maximum 70 mm² conductor cross-section on the feeder terminal block.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Infeed system for 3RA6 ■ Overview (continued) $ Infeed - End covers The 3-phase infeed is available with screw connection (25/35 mm2 up to 63 A or 50/70 mm2 up to 100 A) and springtype connection (25/35 mm2 up to 63 A). On the last expansion module of a row, the socket provided for the expansion plug can be covered by inserting the end cover.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Infeed system for 3RA6 ■ Overview (continued) Maximum rated operational current Proposal for upstream short-circuit protection devices The following maximum rated operational currents apply for the components of the infeed system for 3RA6: The following short-circuit data apply for the components of the infeed system for 3RA6 compact starters.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Infeed system for 3RA6 ■ Selection and ordering data Version Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Infeed system for 3RA6 ■ Selection and ordering data (continued) Version Article No. Expansion modules Two-socket expansion modules with screw or spring-type connection and integrated PE bar with 2 sockets for 2 direct-on-line starters or 1 reversing starter Expansion plug and 2 connecting wedges are included in the scope of supply.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Infeed system for 3RA6 ■ Selection and ordering data (continued) Version Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the control cabinet SIRIUS 3RA6 compact starters > Infeed system for 3RA6 ■ Selection and ordering data (continued) Version Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS M200D motor starters > General data ■ Overview ■ Benefits SIRIUS M200D AS-i Basic motor starters with manual local operation The intelligent, highly flexible SIRIUS M200D motor starters for distributed configurations are designed to start, monitor and protect motors and loads up to 5.5 kW.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS M200D motor starters > M200D motor starters for AS-Interface ■ Overview For motor control using AS-Interface there are the following M200D motor starter versions: SIRIUS M200D AS-i Basic and SIRIUS M200D AS-i Standard (basic functionality see page 4/101 "SIRIUS M200D Motor Starters" "General Data" "Overview").
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS M200D motor starters > M200D motor starters for AS-Interface ■ Overview (continued) SIRIUS M200D SIRIUS M200D AS-i Basic AS-i Standard Device functions (firmware features) Slave on the bus Fieldbus ✓ AS-i Slave type ✓ A/B acc. to Spec 2.1 ✓ A/B acc. to Spec 3.0 Profile ✓ 7.A.E ✓ 7.A.E & 7.A.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS M200D motor starters > M200D motor starters for AS-Interface ■ Overview (continued) SIRIUS M200D SIRIUS M200D AS-i Basic AS-i Standard Device functions (firmware features) Device function 4 Repair switch ✓ Lower current limit monitoring -- ✓ Parameterizable Upper current limit monitoring -- ✓ Parameterizable Zero current detection ✓ Permanent function: disconnection, less than 18.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS M200D motor starters > M200D motor starters for AS-Interface – Basic ■ Selection and ordering data M200D AS-i Basic without manual local control M200D AS-i Basic with manual local control Version Article No. Version Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS M200D motor starters > M200D motor starters for AS-Interface – Standard ■ Selection and ordering data 4 M200D AS-i Standard without manual local control M200D AS-i Standard with manual local control Version Article No. Version Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS M200D motor starters > Accessories ■ Overview 7 NSA0_00484 NSA0_00485a 1 2 9 4 10 4 5 3 6 M 8 1 Power feeder plug 7 Connection for motor control with AS-i communication 2 Power connection plug 8 AS-Interface M12 feeder 3 Incoming energy supply cable 9 Connection for digital input 4 Motor connection plug 5 Motor plug 6 Motor cable Power and motor connection on the M200D
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS M200D motor starters > Accessories ■ Selection and ordering data The accessories listed below represent a basic selection sorted by: • Accessories for all M200D motor starters • Accessories for M200D motor starters for AS-interface Note: More connection technology products, see "Siemens Solution Partners Automation" under "Distributed Field Installation System" technology. Version Article No.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS M200D motor starters > Accessories ■ Selection and ordering data (continued) Version Article No. Motor control with IO communication M12 plugs, straight Screw fixing, 5-pole screw terminals, max. 0.75 mm2, A-coded, max. 4 A 3RK1902-4BA00-5AA0 . M12 plugs, angular Screw fixing, 5-pole screw terminals, max. 0.75 mm2, A-coded, max.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS M200D motor starters > Accessories ■ Selection and ordering data (continued) Version Article No. Only for M200D motor starters for AS-interface Motor control with AS-i communication + Control cables, assembled at one end M12 socket, angular, screw fixing, 4-pole, 4 x 0.34 mm2, A-coded, black PUR sheath, max.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS MCU motor starters for AS-Interface > General data ■ Overview 3RK4320-3.R51-.BA0 3RK4320-3.Q54-.BA. Portfolio of the SIRIUS 3RK43 MCU motor starter family The SIRIUS MCU motor starter family (MCU = Motor Control Unit) rounds off the bottom end of the SIRIUS motor starter range.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS MCU motor starters for AS-Interface > General data ■ Overview (continued) 3RK4320-3.R51-.BA0 Type 4 3RK4320-3.Q54-.BA. 3RK4320-5.Q64-.BA.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection MCU motor starters for AS-Interface > Plastic enclosure, electromechanical switching ■ Overview MCU for AS-i, plastic enclosure • Direct-on-line or reversing starters up to 12 A at 400 V AC (50/60 Hz) • Repair switches (black/gray) lockable with padlocks (max.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS MCU motor starters for AS-Interface > Metal enclosure, electromechanical switching ■ Overview 4 4/114 Siemens IK PI · 2015 1 5 6 3 2 4 nsb0_02040 MCU for AS-i, metal enclosure, electromechanical • Direct-on-line or reversing starters up to 12 A • Repair switches (black/gray) lockable with padlocks (max.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS MCU motor starters for AS-Interface > Metal enclosure, electromechanical switching ■ Selection and ordering data Rated current Ie Suitable for three-phase motors1) with P Setting range Thermal overload release A kW A 0.63 0.18 0.45 ... 0.63 3RK4320-3AQ54- 0BA7 0.8 0.18 0.55 ... 0.8 3RK4320-3BQ54- 0BA7 1 0.25 0.7 ... 1 3RK4320-3CQ54- 0BA7 1.25 0.37 0.9 ... 1.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection SIRIUS MCU motor starters for AS-Interface > Metal enclosure, electronic switching ■ Overview 4 9 1 5 6 3 2 nsb0_02041 MCU for AS-i, metal enclosure, electronic • Direct-on-line or reversing starters up to 12 A • Switching frequency up to 3 600/h • Repair switches (black/gray) lockable with padlocks (max.
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection Motor starters for AS-Interface, 24 V DC ■ Overview Quick-stop function All AS-Interface 24 V DC motor starters feature a quick-stop function which can be switched on and off as required using a switch integrated into the module. The quick-stop function allows a connected motor to be disconnected immediately using an applied sensor signal (High).
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection Motor starters for AS-Interface, 24 V DC ■ Overview (continued) Applications Single direct-on-line starter without brake (with adjustable quick-stop function) 1st possibility: Connection to a maximum of four sensors without pollution indication Sensor signal Sensor signal Sensor signal Sensor signal 4 2 Input 1 off on Quick-stop for output on/off 4 Output 4 Sensor 2 Sensor 3 Sensor 4 Input 2 2 Se
© Siemens AG 2014 AS-Interface Slaves Motor starters for use in the field, high degree of protection Motor starters for AS-Interface, 24 V DC ■ Selection and ordering data Version Inputs/outputs Current carrying capacity of outputs Slave type Article No.
© Siemens AG 2014 AS-Interface Slaves SINAMICS G110D distributed inverters ■ Overview The new SINAMICS G110D distributed frequency inverter series is the solution for basic drive tasks especially in the field of conveyor systems. The inverter allows the speed of three-phase induction motors to be continually controlled and fulfills the requirements of conveyor-related applications with open-loop frequency control.
© Siemens AG 2014 AS-Interface Slaves SINAMICS G110D distributed inverters ■ Benefits • Wide range of power ratings from 0.75 kW to 7.5 kW • Fast commissioning and maintenance as well as extended diagnostic functions and communications capability with AS-Interface according to Specification 3.
© Siemens AG 2014 AS-Interface Slaves SINAMICS G110D distributed inverters ■ Ordering data Article No.
© Siemens AG 2014 AS-Interface Slaves 3SF5 pushbuttons and indicator lights Enclosure and front panel module for AS-Interface > General data ■ Overview Installation of AS-Interface slaves The following slave types are available for connecting the command points: • Slave in A/B technology with 4 inputs and 3 outputs • Slave with 4 inputs and 4 outputs • F Slave with two secure inputs for EMERGENCY-STOP mushroom pushbutton The following table shows the maximum number of equippable slaves: Distributed comma
© Siemens AG 2014 AS-Interface Slaves 3SF5 pushbuttons and indicator lights Enclosure and front panel module for AS-Interface > With standard fittings ■ Overview Enclosures with standard fittings are available with: • 1 to 3 command points, • Operational voltage through AS-Interface (approx. 30 V), • Vertical mounting type • Plastic enclosures are equipped with plastic actuators and indicators, metal enclosures are equipped with metal actuators and indicators.
© Siemens AG 2014 AS-Interface Slaves 3SF5 pushbuttons and indicator lights Enclosure and front panel module for AS-Interface > Components ■ Selection and ordering data For self-equipping of the enclosures Version For plastic enclosures Article No. No. of command points AS-Interface slaves 3SF5500-0BA F slave, 2 safe inputs, for plastic enclosure, EMERGENCY-STOP, without protective collar 1 ...
© Siemens AG 2014 AS-Interface Slaves 3SF5 pushbuttons and indicator lights Enclosure and front panel module for AS-Interface > Customized equipment ■ Overview Connection The customized enclosure is supplied fully equipped and wired. For connection to AS-Interface selection can be made between: • Terminal for shaped AS-Interface cable. The cable is contacted by the insulation piercing method and routed past the enclosure on the outside (possible only with plastic enclosure).
© Siemens AG 2014 AS-Interface Slaves 3SF5 pushbuttons and indicator lights Enclosure and front panel module for AS-Interface > Front panel module ■ Overview AS-Interface cable NSD0_00053b Terminal Series 3SB3 command devices installed in front panels can be connected to the AS-Interface bus system by means of the AS-Interface front panel module. Round or square pushbuttons and indicator lights made of plastic or metal can be used.
© Siemens AG 2014 AS-Interface Slaves 3SF5 pushbuttons and indicator lights Enclosure and front panel module for AS-Interface > Front panel module ■ Selection and ordering data The order codes to be stated on the form can be found in the list of the options which are available for a surcharge. The front panel module must be stated on the order form which is enclosed with the order. This order form cannot be generated by the 3SB3/3SF5 configurator.
© Siemens AG 2014 AS-Interface Slaves 3SF5 pushbuttons and indicator lights Enclosure and front panel module for AS-Interface > Front panel module ■ Selection and ordering data (continued) Selection of equipment according to order form Version Codes according to colors Black Red Yellow Green Blue White Clear Actuators and indicators Pushbuttons with flat button D Illuminated pushbuttons with flat button – Pushbuttons with raised button DH Illuminated pushbuttons with raised button – Pushbu
© Siemens AG 2014 AS-Interface Slaves 3SF5 pushbuttons and indicator lights Enclosure and front panel module for AS-Interface > Front panel module ■ Selection and ordering data (continued) Selection of equipment according to order form Version Codes Key can be removed in position O I II O and I O and II I and II I, O and II Locks with 2 switch positions Switching sequence O-I, latching 4 Type RONIS: Lock No. SB30 RSB 1A RSB 1E – RSB 1AE – – – Type CES: Lock No. SSG 10 Lock No.
© Siemens AG 2014 AS-Interface Slaves 3SF5 pushbuttons and indicator lights Enclosure and front panel module for AS-Interface > Front panel module ■ Selection and ordering data (continued) Selection of equipment according to order form Version Codes Key can be removed in position O I II O and I O and II I and II I, O and II Locks with 3 switch positions Switching sequence I–O–II, latching to the right, momentary contact to the left Type RONIS: Lock No.
© Siemens AG 2014 AS-Interface Slaves 8WD4 signaling columns General data ■ Overview The 8WD4 signaling columns are flexible in design and versatile in use. They are used in machines or in automatic processes for monitoring complex procedures or as visual or acoustic warning devices in emergency situations, e.g. for displaying individual assembly stages.
© Siemens AG 2014 AS-Interface Slaves 8WD4 signaling columns 8WD42 signaling columns, 50 mm diameter ■ Selection and ordering data Acoustic elements Version Rated voltage Color Article No. Buzzer elements 80 dB, pulsating or continuous tone, adjustable by means of a wire jumper 24 V AC/DC Black 8WD4220-0FA Red Green Yellow Clear Blue 8WD4200-1AB 8WD4200-1AC 8WD4200-1AD 8WD4200-1AE 8WD4200-1AF 1) Light elements for incandescent lamps/LEDs, BA 15d bases 2) Continuous light elements 24 ...
© Siemens AG 2014 AS-Interface Slaves 8WD4 signaling columns 8WD42 signaling columns, 50 mm diameter ■ Selection and ordering data (continued) Version Article No. Mounting Feet, single Plastic, for mounting on pipes 8WD4308-0DB Metal, for pipe lengths > 400 mm 8WD4308-0DC Plastic, for floor mounting (without pipe) 8WD4208-0DE Adjustable-angle feet for positioning in 7.5° increments1) Plastic, for mounting on pipes, incl.
© Siemens AG 2014 AS-Interface Slaves 8WD4 signaling columns 8WD44 signaling columns, 70 mm diameter ■ Selection and ordering data Acoustic elements Version Rated voltage Color Article No.
© Siemens AG 2014 AS-Interface Slaves 8WD4 signaling columns 8WD44 signaling columns, 70 mm diameter ■ Selection and ordering data (continued) Version Article No. Mounting 4 Foot with pipe Pipe length 100 mm 8WD4308-0DA Feet, single Plastic, for mounting on pipes 8WD4308-0DB Metal, for pipe lengths > 400 mm 8WD4308-0DC Adjustable-angle feet for positioning in 7.5° increments1) Plastic, for mounting on pipes, incl.
© Siemens AG 2014 AS-Interface Power supply units and data decoupling modules AS-Interface power supply units ■ Overview AS-Interface power supply unit for 3 A AS-Interface power supply units feed 30 V DC into the AS-Interface cable and supply the AS-Interface components. They include power-optimized data decoupling for the separation of communication signals and control supply voltage. As the result, AS-Interface is able to convey both data and power along a single line.
© Siemens AG 2014 AS-Interface Power supply units and data decoupling modules 30 V power supply units ■ Overview Dimensions The 30 V power supply units have compact dimensions in widths of 50 and 70 mm. No distances from other devices need to be observed when mounting the power supply units. Features • Primary clocked power supply units for connection to a singlephase AC network • Power for currents of 3, 4 and 8 A • The output voltage is floating, and resistant to short-circuits and no-load operation.
© Siemens AG 2014 AS-Interface Power supply units and data decoupling modules 30 V power supply units ■ Technical specifications Version 3A 4A 8A Version 3A 4A 8A Approvals Input data • Input voltage, rated value Ue V AC 120 / 230 V, single-phase, automatic selection • UL UL 508 / CSA 22.2 • Pollution degree IEC 60950 • Overvoltage category and electrical separation EN 50178 and IEC 61558 • Input voltage range V AC 85 ... 132 / 174 ...
© Siemens AG 2014 AS-Interface Power supply units and data decoupling modules S22.
© Siemens AG 2014 AS-Interface Power supply units and data decoupling modules S22.5 data decoupling modules ■ Application Construction of an AS-i Power24V network with an AS-Interface S22.
© Siemens AG 2014 AS-Interface Power supply units and data decoupling modules Data decoupling modules for S7-1200 DCM 1271 data decoupling module ■ Overview ■ Application The AS-Interface data decoupling module is designed for AS-Interface networks with 30 V supply or 24 V supply (AS-Interface Power24V).
© Siemens AG 2014 AS-Interface Power supply units and data decoupling modules Data decoupling modules for S7-1200 DCM 1271 data decoupling module ■ Selection and ordering data Version Article No. DCM 1271 data decoupling modules 3RK7271-1AA30-0AA0 • With screw terminals, removable terminals (included in the scope of supply) • Dimensions (W H D / mm): 30 100 75 3RK7271-1AA30-0AA0 ■ Accessories Version 4 Screw terminals Article No.
© Siemens AG 2014 AS-Interface Transmission media AS-Interface shaped cables ■ Overview To enable use in the most varied ambient conditions (e.g. in an oily environment), the AS-Interface cable is available in different materials (rubber, TPE, PUR). For special applications it is also possible to use an unshielded standard round cable H05VV-F 2 x 1.5 mm² according to AS-i Specification. With AS-Interface, data and energy for the sensors (e.g. proximity switches) and actuators (e.g.
© Siemens AG 2014 AS-Interface System Components and Accessories Repeater The following conditions apply: • When used without an extension plug no more than two repeaters are permitted between AS-i master and slave (repeaters connected in series). • When used with an extension plug no more than one repeater is permitted between AS-i master and slave.
© Siemens AG 2014 AS-Interface System Components and Accessories Extension plug ■ Overview The following versions of the extension plug are available: • Extension plug Compact: a passive component that can be connected directly to the AS-Interface shaped cable • Extension plug plus: The Extension plug plus has an integrated A/B slave that enables any undervoltage supply to be signaled to the AS-Interface master.
© Siemens AG 2014 AS-Interface System Components and Accessories Addressing units ■ Overview The innovated addressing unit for AS-Interface of the AS-i Specification V3.0 The addressing unit is used to assign an address during commissioning to each AS-Interface slave. The device detects a connected slave module or a complete AS-i network and displays the found module in the LCD display. Via the Up/Down keys can each address can be individually set.
© Siemens AG 2014 AS-Interface System Components and Accessories Addressing units ■ Technical specifications 3RK1904-2AB02 AS-Interface addressing unit Parameters Measuring range • Voltage • Current (for slaves) V A 2 ... 35 0 ... 0.150 Measuring accuracy in % of the measured value • Voltage • Current (for slaves) % % ± 3.5 + 2 digits ± 5 + 2 digits Input resistance for voltage measurement k 300 Power supply Standard power supply 4 batteries 1.
© Siemens AG 2014 AS-Interface System Components and Accessories Analyzer ■ Overview ■ Benefits • Simple and user-friendly operation enables diagnostics of AS-Interface networks without help from specialists • Speedy troubleshooting thanks to intuitive display in statistics mode • Test logs provide verification of the state and quality of the installation for service and approval • Recorded logs facilitate remote diagnostics by technical assistance • Comprehensive trigger functions enable exact analysis
© Siemens AG 2014 AS-Interface System Components and Accessories Analyzer Data mode 4 Trace mode Presentation of the I/O data: Safety data Presentation of message frames in trace mode The presentation of message frames in the style of a classic fieldbus analyzer is indispensable for complex troubleshooting. Extensive trigger functions and recording and viewing filters are available for this purpose.
© Siemens AG 2014 AS-Interface System Components and Accessories Analyzer ■ Selection and ordering data 3RK1904-3AB01 Version Article No.
© Siemens AG 2014 AS-Interface System Components and Accessories Miscellaneous accessories ■ Selection and ordering data Version Article No. AS-Interface system manual Free download of technical information and overview of the AS-Interface product range from Siemens, scope: approx. 600 pages • For German version, see http://support.automation.siemens.com/WW/view/de/26250840 • For English version, see http://support.automation.siemens.
© Siemens AG 2014 AS-Interface System Components and Accessories Miscellaneous accessories ■ Selection and ordering data (continued) Version Article No.
© Siemens AG 2014 AS-Interface System Components and Accessories Miscellaneous accessories ■ Selection and ordering data (continued) Version Article No. Sealing sets 3RK1902-0AR00 • For K60 mounting plate and standard distributor • Cannot be used for K45 mounting plate 3RK1902-0AR00 • One set contains one straight and one shaped seal.
© Siemens AG 2014 AS-Interface Software AS-Interface block library for SIMATIC PCS 7 ■ Overview Hardware and software requirements The libraries require the following PCS 7 versions: • Engineering software V8: PCS 7 version V8.0 SP1 and higher • Engineering software migration V7-V8: PCS 7 version V8.0 and higher • Engineering software V7: PCS 7 version V6.1, V7.0 or V7.
© Siemens AG 2014 AS-Interface Software AS-Interface block library for SIMATIC PCS 7 ■ Selection and ordering data Version Article No.
