Operating Instructions

ManualsBrandsSiemens ManualsBackupFC122-ZA

www.siemens.com/buildingtechnologies

Siemens Switzerland Ltd

Industry Sector

Building Technologies Division

International Headquarters

Gubelstrasse 22

CH-6301 Zug

Operation (short)

FC120 Fire control panel

ALARM-Procedure Page 1

Switching off detector zones Page 2

Switching on detector zones Page 3

Procedure in case of Fault Page 4

Document ID: A6V10393198_a_en_-- Edition: 2013-05-27

1 / 4

ALARM Procedure

with Alarm Verification Concept (AVC) – suggested possible procedure – subject to local requirements

tion /

Condition

Consequence

Status

Press on the PMI. before allowed reaction time

(V1) runs out (Password required)

è Buzzer is turned off, alarm is acknowledged.

è Countdown V2 for the investigation of the cause of alarm starts.

Read time of top line right side on the display è Remaining time is shown as countdown before Fire Brigade call.

Read fire location on display.

Optional: press on the Person Machine

Interface (password required)

è Deactivates the acoustic alarm devices.

(Reactivation is possible by pressing the button again)

Go to the fire location. è Information on the cause of ALARM

Decide: MAJOR INCIDENT or minor incident. è If required, initiate suitable emergency measures.

MAJOR INCIDENT

Press <alarm delay off>

or actuate nearest manual call point.

è The remote transmission for fire alarm is activated immediately.

Look at the LED indicator

● 'On: Fire brigade called'

● Off: 'Call fire brigade!'

(Remote transmission is switched off / not

available or defective)

ALARM is transmitted to fire brigade.

è Fire brigade must be called by phone!

– No automatic transmission to fire brigade

– Dial the following no.:

Minor incident

Press to reset the panel.

(Password required)

è Fire detection system is in normal condition unless another event

occurs. It may be necessary to vent the room before resetting is

possible. Elements that cannot be reset can be switched off

temporarily.

Fire alarm 2:00

Zone 1 1/1

Meeting room 1

Decide

MAJOR INCIDENT or Minor incident

Go to the fire location.

Summary of content (8 pages)

PAGE 1
Siemens Switzerland Ltd Industry Sector Building Technologies Division International Headquarters Gubelstrasse 22 CH-6301 Zug www.siemens.com/buildingtechnologies ALARM-Procedure Switching off detector zones Switching on detector zones Procedure in case of Fault Operation (short) FC120 Fire control panel Page 1 Page 2 Page 3 Page 4 ALARM Procedure with Alarm Verification Concept (AVC) – suggested possible procedure – subject to local requirements 2. Fire alarm Zone 1 Meeting room 1 2:00 1/1 3. 5.
PAGE 2
Switching off detector zones (password required) The following example represents a possible operation sequence: WARNING System parts that have been switched off make it impossible to acquire and process alarms or faults! Fire may spread unhindered. l Deploy staff to monitor the deactivated area. l You must switch deactivated parts of the 'Site' back on as soon as possible. Step 1. Press the button to open the main menu.
PAGE 3
Switching on detector zones (Password required) l When there is no event with a higher priority, isolations (switched off) are directly indicated on the display. You may then directly proceed with Step 3 below. Step 1. Press the button to open the main menu. (Password required) Result Þ Menu Event summary u Enable / disable u History log u Set date & time u Login u Logout u 2 2. Press to select 'Enable / Disable' and confirm with .
PAGE 4
Procedure in case of Fault Step Result 1. Press on the PMI. Þ Buzzer on the panel is switched off. 2. Read message/fault location on the display. Þ Information on type and place of the fault. 3. Go to the fault location and remedy the cause of the Þ fault. 4. Press on the PMI. 5. Press to reset the panel. When the fault has been eliminated, the system could be acknowledged. The maintenance personnel is called up if the fault dialer is installed.
PAGE 5
Siemens Switzerland Ltd Industry Sector Building Technologies Division International Headquarters Gubelstrasse 22 CH-6301 Zug www.siemens.com/buildingtechnologies ALARM-Procedure Switching off zones Switching on zones Procedure in case of Fault Operation (short) FC120 Fire control panel Page 1 Page 2 Page 3 Page 4 ALARM Procedure no Alarm Verification Concept (AVC) – suggested possible procedure – subject to local requirements Fire alarm Zone 1 Meeting room 1 1/1 3. 5. Go to the fire location.
PAGE 6
Switching off detector zones (password required) The following example represents a possible operation sequence: WARNING System parts that have been switched off make it impossible to acquire and process alarms or faults! Fire may spread unhindered. l Deploy staff to monitor the deactivated area. l You must switch deactivated parts of the 'Site' back on as soon as possible. Step 1. Press the button to open the main menu.
PAGE 7
Switching on detector zones (Password required) l When there is no event with a higher priority, isolations (switched off) are directly indicated on the display. You may then directly proceed with Step 3 below. Step 1. Press the button to open the main menu. (Password required) Result Þ Menu Event summary u Enable / disable u History log u Set date & time u Login u Logout u 2 2. Press to select 'Enable / Disable' and confirm with .
PAGE 8
Procedure in case of Fault Step Result 1. Press on the PMI. Þ Buzzer on the panel is switched off. 2. Read message/fault location on the display. Þ Information on type and place of the fault. 3. Go to the fault location and remedy the cause of the Þ fault. 4. Press on the PMI. 5. Press to reset the panel. When the fault has been eliminated, the system could be acknowledged. The maintenance personnel is called up if the fault dialer is installed.