Technical Manual
Table Of Contents
- 1 About this document
- /
- The information provided in this manual is a summary of the key procedures and functions required to assemble, install, operate, commission and repair the system.
- It is intended to provide experienced and qualified personnel a guide on the required processes.
- The technical manual applies to the Cerberus FIT fire control panel FC12x series.
- The information in this document is intended for the following target groups:
- The reference document has the following designation:
- ID_x_en_--
- x = version, en = English, -- = international
- The list below is used as a reference for the fire control panel FC12x and as a supplement to this document.
- Version
- Edition date
- Brief description
- 2 Safety regulations
- 3 System description
- /
- 4 Installation
- 5 Function overview
- 6 Operation
- AVC
- DIRECT
- Manned
- Unmanned
- The actual events will display all pending events.
- The panel is protected against unauthorized user operation.
- Therefore enter the password or turn the key switch (optional).
- The panel is protected against unauthorized user operation. Therefore enter the password or turn the key switch (optional).
- The alarm counter counts all fire alarms.
- All events such as alarm(s), fault(s), isolation(s), input(s) and output(s) activation are stored in a history log.
- Manual logout to access level 1.
- Each zone can be isolated individually.
- Enable the test mode for each zone.
- Disable outputs generally and / or individually.
- Information about the software is displayed.
- Exit with
. - Exit with
. - Exit with
. - 7 Programming
- Input customer text for:
- 8 Tool function
- 1. Start the Hyper Terminal and enter an appropriate name.
- 2. Select communication port.
- /
- Make sure your PC is connected to the FDUZ22x box and the driver is installed.
- /Make sure your PC is connected to the FDUZ22x box and the driver is installed.Check the communication port on the device manager.
- /
- /
- 1. Select the following option on the panel.
- 2. Enable the Hyper Terminal to receive data.
- /
- /
- /
- /
- /
- 1. Select the following option on the panel.
- 2. Enable the hyper terminal to receive data.
- /
- /
- /
- /
- /
- 1. Select the following option on the panel..
- 2. Enable the hyper terminal to 'Send file'.
- /
- /
- /
- 1. Click
. - 2. Select the folder 'Settings' and click 'ASCII Setup'.
- 5. PC will display as below. Press '2'.
- 6. 'CC…' shows the connection is established and ready for transfer.
- /
- /
- /
- 9 Commissioning
- 10 Maintenance
- 11 Battery capacity
- 12 Trouble shooting
- 13 Components and spare parts
- 14 Disposal and environmental protection
- Appendix A: Site configuration, Factory Setting
- Appendix B: Switch mains to AC 115 V
- Appendix C: History log
A6V10393190_j_en_-- 33
4.6.3 EVAC module (NL)
The EVAC module is available for the following panels.
EVAC Module (NL) FC121-ZA FC122-ZA FC123-ZA FC124-ZA
FTO1201-H1
FTO1203-H1
Function:
The EVAC module NL provides the Dutch special function.
All sounder controls are changed to EVAC sounder NL.
Mounting module before initial start-up:
- If the module is connected before the initial start-up, the NL presetting and language
is pre-selected automatically.
- The functionality and EVAC sounder NL are available if the pre-selected setting is used.
Mounting module after initial start-up:
- Enable the EVAC module in the programming.
- Change all programmed sounder outputs to EVAC sounder NL.
Programming: Configure Accessory EVAC module
Configure Output Output n Mode EVAC Sounder NL
Operating:
All programmed outputs to 'EVAC Sounder NL' are activated by pressing the start
button twice.
No. Description Status Function
1 LED: EVAC zone active ON Evacuation is activated.
2 LED: EVAC fault Flashing Fault on the EVAC sounder lines(s) has occurred.
3 Button: START Press twice to start the evacuation.
4 Button: STOP Press twice to stop the evacuation.
FTO1201-H1
FTO1203-H1
1
2
3
4
FC121-ZA / FC122-ZA
FC123-ZA / FC124-ZA