Technical Manual
Table Of Contents
- 1 About this document
- /
- The information provided in this manual is a summary of the key procedures and functions required to assemble, install, operate, commission and repair the system.
- It is intended to provide experienced and qualified personnel a guide on the required processes.
- The technical manual applies to the Cerberus FIT fire control panel FC12x series.
- The information in this document is intended for the following target groups:
- The reference document has the following designation:
- ID_x_en_--
- x = version, en = English, -- = international
- The list below is used as a reference for the fire control panel FC12x and as a supplement to this document.
- Version
- Edition date
- Brief description
- 2 Safety regulations
- 3 System description
- /
- 4 Installation
- 5 Function overview
- 6 Operation
- AVC
- DIRECT
- Manned
- Unmanned
- The actual events will display all pending events.
- The panel is protected against unauthorized user operation.
- Therefore enter the password or turn the key switch (optional).
- The panel is protected against unauthorized user operation. Therefore enter the password or turn the key switch (optional).
- The alarm counter counts all fire alarms.
- All events such as alarm(s), fault(s), isolation(s), input(s) and output(s) activation are stored in a history log.
- Manual logout to access level 1.
- Each zone can be isolated individually.
- Enable the test mode for each zone.
- Disable outputs generally and / or individually.
- Information about the software is displayed.
- Exit with
. - Exit with
. - Exit with
. - 7 Programming
- Input customer text for:
- 8 Tool function
- 1. Start the Hyper Terminal and enter an appropriate name.
- 2. Select communication port.
- /
- Make sure your PC is connected to the FDUZ22x box and the driver is installed.
- /Make sure your PC is connected to the FDUZ22x box and the driver is installed.Check the communication port on the device manager.
- /
- /
- 1. Select the following option on the panel.
- 2. Enable the Hyper Terminal to receive data.
- /
- /
- /
- /
- /
- 1. Select the following option on the panel.
- 2. Enable the hyper terminal to receive data.
- /
- /
- /
- /
- /
- 1. Select the following option on the panel..
- 2. Enable the hyper terminal to 'Send file'.
- /
- /
- /
- 1. Click
. - 2. Select the folder 'Settings' and click 'ASCII Setup'.
- 5. PC will display as below. Press '2'.
- 6. 'CC…' shows the connection is established and ready for transfer.
- /
- /
- /
- 9 Commissioning
- 10 Maintenance
- 11 Battery capacity
- 12 Trouble shooting
- 13 Components and spare parts
- 14 Disposal and environmental protection
- Appendix A: Site configuration, Factory Setting
- Appendix B: Switch mains to AC 115 V
- Appendix C: History log
64
A6V10393190_j_en_--
C
ok
ok
C
7.5 Customer text
Input customer text for:
Zones, see chapter 7.1.1.
Input function 'class change signal', see chapter 7.1.3.
Service information, see chapter 6.4.11.
The window is structured into the following sectors:
Sector
A
Remaining space, out of 40 on two lines
B Text area
C Selection area of letters, numbers, characters and toggle function
Legend:
Toggle between capital and lower letters
Delete the character to the left of the cursor position
Insert space
Change entry to the second customer text line
Switch to numeric
Switch to letter
Toggle between country specified character
/
Page up / down
7.5.1 Button function
The button function depends on the curser position.
Select the curser position by navigation key.
Curser position, area B
The <ok> button confirms the text entry and
exits the menu.
The <C> button deletes the letter to the left of
the flashing curser.
Curser position, area C
The <ok> button confirms the selected letter.
The <C> button enables the exit and without
save.
7.5.2 Text entry
29 3
Abcdef1s345
q w e r t y u I o p <
a s d f g h j k l , >
z x c v b n m
29 3
Abcdef12345
q w e r t y u I o p <
a s d f g h j k l , >
z x c v b n m
40 3
q w e r t y u I o p <
a s d f g h j k l , >
z x c v b n m
3
B
A
C