Installation Instructions

ManualsBrandsSiemens ManualsFire - LMS Management StationsHUB-4 Communication Card for NCC WAN / PMI-2 Concentrator, Installation Instructions

Fire Safety

P/N 315-096334-2

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 CN

Installation Instructions

FireFinder Upgrade Kits

NCC-G16, NCC-16T

NCC-1T-UK, NCC-2T-UK, NCC-3T-UK, NCC-4T-UK

NCC-GL1

OPERATION

The FireFinder (NCC) Upgrade Kits expand the

operating parameters of an existing NCC system as

follows:

• NCC-G16: provides an existing NCC graphics

system with the capability to control/monitor

additional 16 MXL panels

• NCC-16T: provides an existing NCC text system

with the capability to control/monitor additional 16

MXL panels

• NCC-1T-UK allows an existing NCC-1T (16

node/text) to upgrade to a NCC-1G (16 node/

graphics)

• NCC-2T-UK allows an existing NCC-2T (32

node/text) to upgrade to a NCC-2G (32 node/

graphics)

• NCC-3T-UK allows an existing NCC-3T (48

node/text) to upgrade to a NCC-3G (48 node/

graphics)

• NCC-4T-UK allows an existing NCC-4T (64

node/text) to upgrade to a NCC-4G (64 node/

graphics)

• NCC-GL1 allows an existing NCC-GL system to

upgrade to a NCC-1G (16 node/graphics)

All FireFinder (NCC) upgrade kits are compatible with

both the NCC OS/2 version and NCC NT™ version.

The minimum NCC software revision required to

recognize the NCC software upgrade keys is 2.23 for

the OS/2 version and 4.01 for the NT™ version.

FireFinder Upgrade Kits include an NCC Upgrade

Software Key and NCC Manual (not included with the

NCC-16 or NCC-GL1 series). The existing NCC

components such as NCC software program,

keyboard templates, and NCC-1F card remain the

same.

INSTALLATION

1.Your existing NCC computer should have the

original NCC software key plugged into the LPT

2 port as shown in Figure 1 on the next page.

2.Insert your NCC upgrade software key directly

into the existing NCC software key. Secure key

connection with screw terminals. See Figure 2

on the next page.

3.Once the NCC upgrade software key is securely

attached to the original NCC software key, reboot

the computer.

Summary of content (4 pages)

PAGE 1
Fire Safety Installation Instructions FireFinder Upgrade Kits NCC-G16, NCC-16T NCC-1T-UK, NCC-2T-UK, NCC-3T-UK, NCC-4T-UK NCC-GL1 OPERATION The FireFinder (NCC) Upgrade Kits expand the operating parameters of an existing NCC system as follows: • NCC-G16: provides an existing NCC graphics system with the capability to control/monitor additional 16 MXL panels All FireFinder (NCC) upgrade kits are compatible with both the NCC OS/2 version and NCC NT™ version.
PAGE 2
NOTES: Monitor (rear view) 1. NCC-1F card is installed in a 16-bit ISA slot and is set for COM2. 120 VAC 60 Hz SCD19TM or SCD21TM Touch Interface Port A See Notes 3 and 4 Elo Touch Screen Controller Card See Note 14 2 1 7. Cable must be in rigid conduit and cannot leave the room. COM 2 8. Shielded cable is not recommended. (NCC Key) *The COM port on the Main CPU must be disabled if NCC-1F is being used. See Note 13 4. The computer is supervised for power and connection to MXL. 6.
PAGE 3
4.To reboot the NCC computer, first press the Alt + F4 keys simultaneously to close the NCC program. The following window pops up: In this window, you will see the statement: If you do not want to restart the NCC, hit CTRL-C. Press the Ctrl key and the C key simultaneously. The following statement appears: Terminate batch job (Y/N)? as shown in the following window: Figure 3 NCCNT Command Center Close Window Click the OK button. The same window pops up a second time. Click on the OK button again.
PAGE 4
The following window appears: Select OK. The following window appears: button on the main display, then hit the SETUP button. From the system setup notebook, hit the DISPLAY tab. You will see the enable graphics display option. Click in the adjacent box so that a check mark ( ) appears next to the option. This check mark assures that the option has been activated. Once activated, hit the SAVE button to save this option; then hit DONE to get back to the main display.