Installation Instructions

ManualsBrandsSiemens ManualsFire - LMS Management StationsHUB-4 Communication Card for NCC WAN / PMI-2 Concentrator, Installation Instructions

Siemens Building Siemens Building

Siemens Building

ecec

hnologieshnologies

hnologies

Fire SFire S

Fire S

afetyafety

afety

P/N 315-050253-0

Upgrade Kit For The Network Command Center Using Windows XP™

Installation Instructions

Model NCCXP-UK

Software Installation All SBT, Inc. computers are preloaded with the NCCG software. Follow the procedure

below to:

• re-install the software when necessary. (Start with Step 1.)

• upgrade a system. (Start with Step 4.)

• install the system on a computer that is not preconfigured from

SBT, Inc. (Start with Step 1.)

1. Next, proceed with the software installation procedure outlined below.

• Install MS Windows XP Pro™ which includes Service Pack 2 (if

necessary).

• Insert your NCCG software key into an available parallel port.

• Logon as administrator.

• Add the user name "firefinder" and password "firefinder":

- Navigate from the START button Start> Settings> Control

Panel.

- Click on the User Accounts icon.

- Click on Create A New Account (refer to Figure 1).

- Type "firefinder" as the name for the new account.

- Click on the Next button.

- Select Computer Administrator (refer to Figure 2).

- Click on Create Account button.

- In the User Accounts window, click on the FireFinder icon.

- Select Create Password.

- Fill in the following information:

Password = firefinder

Confirm Password - firefinder

- Click on Create Password.

• In a similar manner, add the user name "maintenance". This time,

however, use a secret password. (Default - siemens)

• Exit the User Accounts window.

Summary of content (14 pages)

PAGE 1
Installation Instructions Model NCCXP-UK Upgrade Kit For The Network Command Center Using Windows XP™ Software Installation All SBT, Inc. computers are preloaded with the NCCG software. Follow the procedure below to: 1. • re-install the software when necessary. (Start with Step 1.) • upgrade a system. (Start with Step 4.) • install the system on a computer that is not preconfigured from SBT, Inc. (Start with Step 1.) Next, proceed with the software installation procedure outlined below.
PAGE 2
Figure 1 Create A New Account Figure 2 Choose An Account Type 2. Open the Windows Control Panel by navigating from the START button. Start > Control Panel, then click on Switch To Classic View on the left side of the screen. If Switch To Classic View is not visible on the left side of the screen, you are already in the classic view control panel window.
PAGE 3
• From the Windows Control Panel, select the Date/Time tool. Check that the time, date and time zone settings are correct. • From the Windows Control Panel, open the Printer tool and add any additional printers required. Refer to the Windows XP™ manual for more information. No printer or printer spool can be connected to LPT1. Doing so will prevent proper operation of the paper out and printer off line function. • From the Windows Control Panel, open the Display tool and go to the Settings tab.
PAGE 4
Figure 3 Java Runtime Opening Screen Click on Yes to accept the licensing agreement. The next installation Screen will appear (refer to Figure 4). Figure 4 Java Runtime Installation Destination Click on Next to run the installation process. It is recommended not to change the destination folder. 7. Siemens Building Technologies Fire Safety Sentinel Driver 7.4.
PAGE 5
Figure 5 Sentinel Driver Setup Opening Screen Click on Next to continue the installation process. The License Agreement screen will appear (refer to Figure 6). Select I accept the terms in the license agreement, then click Next . Figure 6 Sentinel Driver Licensing Agreement The Setup Type screen will appear (refer to Figure 7). Select Custom, then click Next.
PAGE 6
Figure 7 Sentinel Driver Setup Type The Custom Setup screen will appear (refer to Figure 8). Unselect Sentinel Protection Server and Sentinel Keys Server. Click Next to run the installation process. Figure 8 8. Siemens Building Technologies Fire Safety Sentinel Driver Custom Setup Adobe Acrobat Reader 4.0 - After the Sentinel Driver installation is completed, the Adobe Acrobat Reader installation will start with the following screen (refer to Figure 9).
PAGE 7
Figure 9 Adobe Acrobat Opening Screen Click on Next to continue the installation process. The License Agreement screen will appear (refer to Figure 10). Click Accept to accept the licensing agreement. Figure 10 Adobe Acrobat Licensing Agreement The next installation Screen will appear (refer to Figure 11). Click on Next to choose the default destination folder and run the installation process.
PAGE 8
Figure 11 Adobe Acrobat Reader Installation Destination 9. Microsoft IIS - After the Acrobat Reader installation is completed, the Microsoft IIS installation will start with the following screen (refer to Figure 12). Figure 12 Microsoft IIS Opening Screen Remove the NCC CD from the CD-ROM drive and insert the Windows XP™ CD. Click OK. If the Microsoft Windows XP™ welcome screen appears, click Exit to close the window (refer to Figure 13).
PAGE 9
Figure 13 Microsoft Windows XP™ Welcome Screen 10. NCC MP7 - After the IIS installation is completed, the NCC installation will start with the following screen (refer to Figure 14). Figure 14 NCC MP7 Installation Opening Screen Click on Next to continue the installation process. The Setup Type screen will appear (refer to Figure 15).
PAGE 10
Figure 15 NCC MP7 Setup Type You have the option to select either Complete or Custom install. By default, the NCC files will be installed in a folder named NCC2. If that destination is acceptable, click Next. If you would like to install these files in a different folder, select Custom install. Then, click Next.
PAGE 11
Figure 17 NCC MP7 Current Settings List The Current Settings list will show the components being installed as follows: NCC-MP7 NCC Web Interface (Window XP Only if not already installed)) Click on Next. The installer will copy the files and the install will be completed (refer to Figure 17). If this is an upgrade, the installation in complete. Restart XP by selecting StartShutdown-Restart. For new installations or re-installations, continue with Step 11. 11.
PAGE 12
When the NCCG restarts, the NCC program will autorun and begin to prompt you for your system configuration data as follows: Figure 18 NCC-G/NCCWAN and NCC-GL Installation and Setup Screens • To proceed with the installation, press the NEXT button. • After the NEXT button is pressed, the following screen appears, as applicable: Figure 19 NCC-G and NCC-GL Node and Module Identification Screens • The Use NIM Interface option is used with the NIM-1R to extend the NCCGL topography.
PAGE 13
• Once the node number assignment and label have been accepted, the following screen appears: Figure 21 NCC-G Installation and Setup • Press the NEXT button to continue with basic system configuration. The following screen appears: Figure 22 NCC-G/GL Site Information • System Identification: Enter the name of the installed site, up to 52 characters long. • Serial #: The number displayed is the version of the NCCG software.
PAGE 14
• Foreign Language Support: Check "Enable Support" and choose a country and language from the options available on each menu. • If System Identification is left blank, the following dialog box appears: Figure 23 NCCG Missing Site Information • After pressing the DONE button in the site information section, the following screen appears, as applicable: Figure 24 NCC-G/NCCWAN and NCC-GL Installation Completion Screens • Siemens Building Technologies, Inc.