Installation Instructions

ManualsBrandsSiemens ManualsFire - LMS Management StationsHUB-4 Communication Card for NCC WAN / PMI-2 Concentrator, Installation Instructions

Siemens Siemens

Siemens

IndustryIndustry

Industry

Inc. Inc.

Inc.

SmarSmar

Smar

t Infrastructt Infrastruct

t Infrastruct

ureure

ure

P/N 315-099458-10

Model HUB-4

INTRODUCTION The Model HUB-4 Communication Card from Siemens Industry, Inc., mounts in the

CC-5 Card Cage and provides up to four independent data channels, which can be

wired as either Style 4 or Style 7. For NCC WAN, the module provides connection to

remote XLS, MXL, XL3, or to other UL864 listed local fire alarm panels providing dry

relay contacts that can be used for event monitoring. For Desigo CC/Cerberus DMS

WAN, the module provides connection to remote XLS/Desigo Fire Safety Modular/

Cerberus PRO Modular panels.

The HUB-4 consists of a single Main-2 board on which two COM-2 boards are

installed. In turn, up to two modem or RS-485 Interface blocks can be installed on

each COM-2 board. Each modem block installed provides a single FSK data channel.

Each RS-485 Interface block installed provides a proprietary RS-485 interface channel.

Either a RS-485 Interface or a Modem Block module can be used, dependent on

application. Table 1 describes the connections that can be made.

1ELBAT

SEPYTNOITCENNOCDNASLENAPERIFDNA4-BUH

NAWCCN NAWSMDSUREBREC/CCOGISED

LENAP584-SRMEDOM584-SRMEDOM

BssalC

)

4elytS(

AssalC

)7elytS(

BssalC

)4elytS(

AssalC

)7elytS(

BssalC

)4elytS(

AssalC

)7elytS(

BssalC

)4elytS(

AssalC

)7elytS(

3LX A/NA/NXMMXMMA/NA/NA/NA/N

LXM A/NA/N003-IMC003-IMCA/NA/NA/NA/N

LXM-ISF

W1-MINA/N

dnaM1/W1-MIN

kcolBmedoM

A/NA/NA/NA/NA/N

traP-drihT

OIAWOIAWA/NA/NA/NA/NA/NA/N

SLX-ISF

MPR/BUHBUHBUHA/NBUHBUHBUHA/N

-rebreC-ISF

ORPsu

raludoM

A/NA/NA/NA/NBUHBUHBUHA/N

ogis

eD-ISF

ytefaSeriF

raludoM

A/NA/NA/NA/NBUHBUHBUHA/N

Communication Card for NCC WAN and Desigo CC/Cerberus DMS WAN

Installation Instructions

Figure 1

HUB-4 Communication

Card

Summary of content (18 pages)

PAGE 1
Installation Instructions Model HUB-4 Communication Card for NCC WAN and Desigo CC/Cerberus DMS WAN INTRODUCTION The Model HUB-4 Communication Card from Siemens Industry, Inc., mounts in the CC-5 Card Cage and provides up to four independent data channels, which can be wired as either Style 4 or Style 7. For NCC WAN, the module provides connection to remote XLS, MXL, XL3, or to other UL864 listed local fire alarm panels providing dry relay contacts that can be used for event monitoring.
PAGE 2
Each of the four data channels is controlled by a separate micro-controller which provides all background supervision of the data lines (to the remote panel) as well as sending and receiving Fire Panel information to the primary micro-controller. The information from these four channels is concentrated into a single data stream and sent to the NCC WAN or Desigo CC/Cerberus DMS WAN via the NIC-C.
PAGE 3
Controls and Indicators The front panel of the HUB-4 contains one reset switch, 15 LEDs and three HNET address switches as shown in Figure 1. A reset switch is located on the top of the front panel. Pushing the reset switch reinitializes the HUB-4 operation. The LEDs follow the reset switch and their functions are defined as follows: POWER (Green) Normally ON. When illuminated, indicates that power for the HUB-4 is applied to the card. CARD FAIL (Yellow) Normally OFF.
PAGE 4
OPEN/SHORT (Yellow) Normally OFF. When consistently illuminated, the HUB4 has detected an OPEN/SHORT in either the primary or secondary wired communications line. When flashing, there is a loss of communications between the HUB-4 main module, and the specific HUB-4 communication port. If the HNET FAIL LED is also illuminated, this port has been muted. CARRIER FAIL (Yellow) Normally OFF.
PAGE 5
3. HUB-4, COM-2 Board: Make sure that the jumper settings are correct for the desired application (either Modem Block or RS-485 Interface Module). Refer to Table 2 and Figure 3 for the correct placement of jumpers on P5 and P6.
PAGE 6
3. Using the three nylon spacers provided with each HUB-4, COM-2, place the screw end of the spacers through the holes in the top of the HUB-4, Main-2 board. (Refer to Figure 4, page 5.) 4. Secure the spacers in place on the underside of the HUB-4, Main-2 board with the nylon nuts provided. 5. Connect the HUB-4, COM-2 to the HUB-4, Main-2 by lining up the 2x15 connectors on the HUB-4 COM-2 to the 2x15 receptacles on the HUB-4, Main-2. Keep in mind that Port 1 is the P1 receptacle, etc.
PAGE 7
NUT SPACER SCREW TABLE 4 HUB-4 MODULE PLACEMENT Number of Channels MODEM BLOCK OR RS-485 INTERFACE MODULE PLACEMENT HUB-4 COM-2 PLACEMENT PORT 1 Place HUB-4 COM-2 on P1 of HUB-4 Main-2 Place Modem Block or RS-485 Interface Module on P1 of HUB-4 COM-2 1 2 Place HUB-4 COM-2 on P1 of HUB-4 Main-2 Place first Modem Block or RS-485 Interface Module on P1 of HUB-4 COM-2; Place second Modem Block or RS-485 Interface Module on P2 of HUB-4 COM-2 1 2 3 Place first HUB-4 COM-2 on P1 of HUB-4 Main-2; P
PAGE 8
2 1 J3 1 2 RS485 INTERFACE J2 Figure 6 RS-485 Interface Module MODEM BLOCK MODULE JUMPER SETTINGS The Modem Block module has three configuration jumpers: JP1, JP2, and JP3. Refer to Figure 7 for the location of the jumpers. Set the jumpers to the configuration shown in Table 5. Refer to the Modem Block Installation Instructions, P/N 315-099356, for further information.
PAGE 9
Verify that the DIN connectors of the card and the cardcage aligned properly. The card can only plug in one direction to the card cage, if it does not align, DO NOT FORCE the card. Place thumbs on the front panel adjacent to the captive screws and gently apply even pressure on the card until the connectors seat in the receptacles on the motherboard. Secure with the captive screws. Connect the modem or RS-485 Interface transmission lines to the correct CC-5 screw terminal connectors on the HUB-4 board.
PAGE 10
ELECTRICAL RATINGS Input Power 24V Back Plane Current Screw Terminal 24V Current 6.2V Back Plane Current 24V Standby Current Output Power Each modem Channel pair 0 400mA 30mA 400mA 2V peak-to-peak max 1.3mA max Maximum line attenuation -23dbm @ 2.5KHz 8V peak-to-peak 75mA during message transmission Each RS-485 Interface RS-485 output pair 560 OHM EOL P/N 140-988066 NOTES 1. Mount the LLM-1 within the MXL enclosure.
PAGE 11
TYPICAL CLASS A (STYLE 7) CONNECTION 3 4 TB1 2 1 2 3 4 TWO 2-WIRE 18 AWG CABLE MIN* 600 OHM MAX LINE RESISTANCE TOTAL PER PAIR MODEM 2 + 1 2 + 4 + 3 + 2 - 1 A B B A - TB2 LLM-1 - 1 (CMI-300) - MOM-4 3 4 5 6 7 8 PSC-12 9 10 11 12 13 A B B A A 14 15 16 B A RESET POWER MODULE FAIL TB2 LLM-1 1 2 3 + + 24V 4A FAIL HUNDREDS TENS ONES HNET MODEM 3 4 GND FAULT 24V 12A FAIL + *USE 2-WIRE COPPER CABLE, 105 C, 300V, 18 AWG, SOLID OR STRANDED, MAX 7 STR
PAGE 12
MMX-1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2 3 + A B + + - 1 - B A B 4 5 6 - A - + MODEM 2 B A 7 8 PSC-12 RESET POWER 9 10 11 12 13 14 15 16 A B B A A B B A - HNET FAIL - CAN FAIL + MODULE FAIL GND FAULT 24V 12A FAIL 24V 4A FAIL + + MODEM 3 - ONES HNET - TENS + HUNDREDS MODEM 4 ONE SLOT OF CC-5 #1 WITH HUB-4 INSTALLED 17 O — 18 19 20 21 22 23 24 ON OFF BATTERY TB2 TB4 12 _ + _ + NON- POWER LIMITED OUTPUT (24VDC @ 12A
PAGE 13
12 11 10 9 8 7 6 5 4 3 2 1 TB1 120 OHMS EOLR 120 OHMS EOLR + 1 1 2 4 3 A B B + 2 A A B B 4 5 11 12 13 B B A A A 3. 200 ohms max per pair. 0.34 μF max line to line. 18 19 15 16 B A B MODEM OR RS-485 INTERFACE 4 20 Figure 12 Typical Class B (Style 4) Wiring to WAIO Connection (NCC WAN only) TB1 8 ONE SLOT OF CC-2/5 WITH HUB-4 INSTALLED 17 1 7 14 + 10 + 9 MODEM OR RS-485 INTERFACE 3 2.
PAGE 14
x The interface type 120 OHM EOL (For use with RS-485 only) P/N 140-049099 (Modem or RS-485) must match on each COM-2 card.
PAGE 15
TB1 * The LLM-1 inserts 10 ohms between TB1 and TB2 terminals 2 and 3 (20 ohms total). 120 OHM EOL P/N 140-049099 x 1 The interface type (Modem or RS-485) must match on each COM-2 card.
PAGE 16
TB1 The interface type Modem or RS-485) must match on each -2 card. If only one interface is used on a COM-2 card, it must be placed on #1 or Port #3 1 MODEM OR OR RS-485 INTERFACE Port #2x + A + B - - B A + A + B 1 * The LLM-1 inserts 10 ohms between TB1 and TB2 terminals 2 and 3 (20 ohms total). 2 3 4 LLM-1 * 2 3 1. FSK @ 19.2kbps Transmit level: 10Dbm Receive level: 43 Dbm 2. Modem Ratings 14-18 AWG 10 miles Max. 20 AWG 6 miles Max. 22 AWG 4 miles Max. 0.
PAGE 17
CYBER SECURITY DISCLAIMER Siemens provides a portfolio of products, solutions, systems and services that includes security functions that support the secure operation of plants, systems, machines and networks. In the field of Building Technologies, this includes building automation and control, fire safety, security management as well as physical security systems.
PAGE 18
Siemens Industry, Inc. Smart Infrastructure Florham Park, NJ Siemens Canada, Ltd.