Installation Instructions

ManualsBrandsSiemens ManualsHome building and DecorFIREFINDER-XLS

Siemens Building Technologies

Fire Safety

P/N 315-048637C-3

Models ILED-SC and ILED-SW

Intelligent Remote Lamps

INTRODUCTION The Models ILED-SC (round plate) and ILED-

SW (rectangular plate) Addressable Remote

Lamps from Siemens Building Technologies,

Inc., shown in Figure 1, operate as an

additional multi-color LED indicator for a

device in the FS-250C System’s FDLC loop

circuit. The ILED-S can be used when a

device already has an accessory. The ILED-S

can be installed at any location of an FDLC

loop, and it remotely indicates the status of

the device(s) in that same loop.

Modes of Operation The ILED-S has two modes of operation:

Passive Mode and Direct Addressing Mode. Use the two-position jumper P1 to set

the mode.

When set to Passive mode, the ILED-S remotely duplicates the on-board LED status

of a device with the same address. In Passive Mode, the ILED-S is not supervised

and cannot relay information to the panel.

When set and programmed to Direct Addressing Mode, the ILED-S uses its own

unique address to follow the status of a single device or a group of devices in the

same addresssable device circuit.

Controls and Indicators The LED indicator is capable of flashing any one of three distinct colors: green,

yellow, or red. In passive mode, the ILED-S continuously checks the information on

the loop for the device it is programmed to follow.

Based on the results of these checks, the LED indicator flashes the following:

roloChsalFnoitidnoC

lavretnIhsalF

)sdnoceS(

DEL

*neerG.noitarepoyrosivrepuslamroN4

wolleY

siro)riaperrogninael

c(ecivresseriuqereciveD

.snoitacificepslatnemnorivnestidnoyebgnitarepo

deRmralA4

sehsalFoN.riaperseriuqerr

o,derewoptonsieciveD-

.loot2TC-SFehtni"detavitcaeDDEL"gnitcelesybffodenrutebnacDEL*

ILED-SW

ILED-SC

Figure 1

ILED-SC And ILED-SW Remote Lamps

Summary of content (4 pages)

PAGE 1
Installation Instructions Models ILED-SC and ILED-SW Intelligent Remote Lamps INTRODUCTION The Models ILED-SC (round plate) and ILEDSW (rectangular plate) Addressable Remote Lamps from Siemens Building Technologies, Inc., shown in Figure 1, operate as an additional multi-color LED indicator for a device in the FS-250C System’s FDLC loop circuit. The ILED-S can be used when a device already has an accessory.
PAGE 2
In Direct Addressing mode, the LED on the ILED-S is controlled by logic functions programmed using the FS-CT2 Tool. In Direct Addressing Mode, the ILED-S blinks red only. In Canada, ILED-Ss configured for Direct Addressing mode must be configured in the FS-CT2 Tool as follows: Flash Color Red PROGRAMMING Usage Alarm Yellow Supervisory Yellow Trouble Green Normal Refer to Figure 2 for the location of the programming holes and jumper P1.
PAGE 3
. Connect the ILED-S to the SDPU Device Programming Unit by inserting the plug from the SDPU cable provided with the SDPU into the programming holes on the ILED-S board. 4. Follow the instructions in the SDPU Manual, P/N 315-033260C, to program the ILED-S to the desired address. Record the device address on the label located on the ILED-S front panel. 5. In the FS-CT2 Programming Tool, assign the ILED-S to an output zone.
PAGE 4
DO NOT USE REAR CONDUIT ENTRY SINGLEGANG SWITCHBOX (USER SUPPLIED) ILED-SW Figure 4 Mounting The ILED-SW The number of ILED-S modules on the FDLC loop must be included in the total count of intelligent field devices regardless of the mode for which the ILED-S was set. For the restriction of the total number of devices in the FDLC loop, refer to the FS-250C Installation, Operation and Maintenance Manual, P/N 315-049589C.